RAB LES13NW LED Flood Light Instruction Manual
- June 13, 2024
- RAB
Table of Contents
RAB LES13NW LED Flood Light
Product Information
RAB Lighting is dedicated to producing high-quality, cost-effective, well- designed, and energy-efficient LED lighting and controls. These products are designed to simplify installation for electricians and help end users save energy. If you have any feedback or questions, please get in touch with our Marketing Department by calling 888-RAB-1000 or emailing marketing@rablighting.com.
Important Instructions
Wall Mounting:
- Mount the fixture to a weatherproof Junction Box (not included) and Cover Plate (not included) as shown in Fig. 1.
- Apply weatherproof silicone sealant around the edge of the Junction Box, especially if the wall surface is uneven.
- Connect the wires according to the wiring section (Fig. 3).
- Attach the Cover Plate to the Junction Box.
- Aim the fixture in the desired direction and tighten the locknut and Arm Screw.
Ground Mounting:
- Mount the fixture to a Mighty Post (RAB Cat# MP19) as shown in Fig. 2.
- Connect the wires according to the wiring section (Fig. 3). Ensure all wires are pushed inside the Mighty Post Cap (ordered separately).
- Place the Mighty Post Cap on the Mighty Post.
- Aim the fixture in the desired direction and tighten the locknut and Arm Screw.
On-Off Wiring
The fixture operates only at 120V, 50/60 Hz. Follow these steps:
- Connect the black fixture lead to the LINE supply lead.
- Connect the white fixture lead to the COMMON supply lead.
- Connect the GROUND wire from the fixture to the supply ground.
Troubleshooting
- Check that the line voltage at the fixture is correct. Refer to wiring directions.
- Ensure the fixture is properly grounded.
Cleaning & Maintenance
CAUTION: Make sure the fixture temperature is cool enough to touch. Do not clean or maintain while the fixture is energized.
- Clean the polycarbonate lens with a non-abrasive cleaning solution.
- Do not open the fixture to clean the LEDs. Avoid touching the LEDs.
Note : These instructions may not cover all details or variations in equipment, nor do they account for every possible situation during installation, operation, or maintenance.
Product Support
- For product information, visit our website at rablighting.com.
- Contact our Tech Help Line at 888 722-1000 for expert assistance.
- For prompt responses, email us at sales@rablighting.com.
- We offer free lighting layouts, available online or by request.
RAB WARRANTY: Our warranty is subject to all terms and conditions found at rablighting.com/warranty.
PATENT: Patent information can be found at rablighting.com/ip.
RAB Lighting is committed to creating high-quality, aff ordable, well-designed and energy-effi cient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE
REFERENCE. RAB fi xtures must be wired in accordance with the National
Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF
THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING : Make certain power is OFF before installing or maintaining
fixture. No user serviceable parts inside.
CAUTION : For proper weatherproof function all gaskets must be seated
properly and all screws inserted and tightened Firmly. Apply weatherproof
silicone sealant around the edge of the ceiling mounting box and/or junction
box. This is especially important with an uneven ceiling surface. Silicone all
plugs and unused conduit entries
WALL MOUNTING
Mount to a weatherproof Junction Box (not supplied) and Cover Plate (not supplied) as shown in Fig. 1. Apply weatherproof silicone sealant around the edge of the Junction Box. This is especially important with an uneven wall surface.
- Thread fi xture into Cover Plate. Use silicone sealant or Tefl on® tape around the thread of the arm.
- Connect wires as shown in the wiring section (Fig. 3).
- Attach Cover Plate to Junction Box.
- Aim fi xture in the desired direction and tighten locknut and Arm Screw.
GROUND MOUNTING
Mount to a Mighty Post (RAB Cat# MP19) as shown in Fig. 2.
- Thread fixture into Mighty Post Cap (ordered separately). Use silicone sealant or Tefl on® tape around the thread of the arm.
- Connect wires as shown in the wiring section (Fig. 3). Push all wires inside the Mighty Post Cap (ordered separately).
- Place Mighty Post Cap on the Mighty Post.
- Aim fixture in the desired direction and tighten the locknut and Screw.
ON-OFF WIRING
Operates only at 120V, 50/60 Hz.
- Connect the black fixture lead to the LINE supply lead.
- Connect the white fixture lead to the COMMON supply lead.
- Connect the GROUND wire from fi xture to supply ground.
TROUBLESHOOTING
- Check that the line voltage at the fixture is correct. Refer to wiring directions.
- Be sure the fixture is grounded properly.
CLEANING & MAINTENANCE
CAUTION : Be sure the fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.
- Clean polycarbonate lens with a non-abrasive cleaning solution.
- Do not open the fixture to clean the LEDs. Do not touch the LEDs
Note : These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during
installation, operation or maintenance.
Visit our website for product info rablighting.com
Tech Help Line
Call our experts: 888 722-1000
e-mail Answered promptly –
sales@rablighting.com
Free Lighting Layouts
Answered o © 2022 RAB LIGHTING Inc. online or by request
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at
rablighting.com/warranty PATENT: Patent
information can be found at rablighting.com/ip
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>