Fein ASCS6.3 Cordless Metal Screwdriver Instruction Manual

June 3, 2024
Fein

Fein ASCS6.3 Cordless Metal Screwdriver

PARTS

Fein-ASCS6.3-Cordless-Metal-Screwdriver-fig1

INSTALLATION

Fein-ASCS6.3-Cordless-Metal-Screwdriver-fig2 Fein-ASCS6.3-Cordless-Metal-Screwdriver-fig3 Fein-ASCS6.3-Cordless-Metal-Screwdriver-fig4 Fein-ASCS6.3-Cordless-Metal-Screwdriver-fig5 Fein-ASCS6.3-Cordless-Metal-Screwdriver-fig7 Fein-ASCS6.3-Cordless-Metal-Screwdriver-fig8 Fein-ASCS6.3-Cordless-Metal-Screwdriver-fig9 Fein-ASCS6.3-Cordless-Metal-Screwdriver-fig11

Symbols, abbreviations and terms used

Fein-ASCS6.3-Cordless-Metal-Screwdriver-fig12 Fein-ASCS6.3-Cordless-Metal-Screwdriver-fig13

For your safety.

WARNING

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. Do not use this power tool before you have thoroughly read and completely understood this Instruction Manual and the enclosed “General Safety Instructions” (document number 3 41 30 465 06 0). The documents mentioned should be kept for later use and enclosed with the power tool, should it be passed on or sold. Please also observe the relevant national industrial safety regulations.
Intended use of the power tool:
Hand-guided screwdriver for screwing in and unscrewing screws, especially for self-drilling and self-cutting screws, in weather-protected environments, using the application tools and accessories recommended by FEIN.
Special safety instructions.
Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. Beware of any concealed electric cables, gas or water conduits. Check the working area before commencing work, e. g. with a metal detector. Secure the workpiece firmly. A workpiece that is gripped tightly in a clamping device or vice, is more secure than if held by hand. Hold the power tool firmly. High reaction torque can
briefly occur. Do not work with materials containing magnesium. The danger of fire. Do not work with CFRP (carbon-fiber-reinforced polymer) and materials containing asbestos. These materials are considered carcinogenic. Do not rivet or screw any nameplates or signs onto the power tool. If the insulation is damaged, protection against an electric shock will be ineffective. Adhesive labels are recommended.Do not use accessories that are not specifically designed and recommended by the power tool manufacturer. Safe operation is not ensured merely because an accessory fits your power tool. Use and handling of the battery (battery pack). To avoid hazardous situations such as burns, fire, explosion, skin injuries, and other injuries when handling the battery, observe the following instructions: Batteries must not be disassembled, opened or reduced in size.

Do not subject batteries to mechanical impact or shock. Hazardous vapours and fluid can escape in case of damage and improper use of the battery. The vapors can irritate the respiratory system. Liquid ejected from the battery may cause skin irritations or burns. When battery fluid from a damaged battery has come into contact with objects close by, check the respective components, clean them or replace them as required. Keep the battery away from heat and fire. Do not store the battery in direct sunlight. Do not remove the battery from its original packaging until it is going to be used. Before any work on the machine itself, remove the battery from the power tool. If the power tool accidentally
starts, there is a danger of injury. Remove the battery only when the power tool is switched off. Keep the battery away from children. Keep the battery clean and protect it against moisture and water. Clean contaminated battery terminals and power tool connections with a dry, clean cloth. Use only intact original FEIN batteries that are intended for your power tool. When working with and charging incorrect, damaged, repaired or reconditioned batteries, imitations or other brands, there is a danger of fire and/or explosion. Follow the safety warnings in the operating instructions of the battery charger.

Hand/arm vibrations
The vibration emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with another. It may be used for a  preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However, if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintaining the tool and the accessories, keep the hands warm, and organization of work patterns.

Operating Instructions

Adjust the rotation selector switch only when the machine is at a complete stop. To avoid accidental starting, e. g., during transport, set the rotary selector switch to the center position. When overheated, the machine runs with short, low-power impulses. Allow the machine to cool down at no-load speed. For reliable working results, always carry out screwdriver operations using the depth stop.

Electronic torque shut-off

The electronic torque shut-off can be used when working without depth stop. Adjust the torque only when the machine is at a complete stop. The motor switches off when reaching the set torque and an audio signal sounds. After the shut-off has taken place, release the on/off switch and press it again for the next screw-driving operation. The audio signal can be switched on and off. The electronic shut-off is deactivated when working in “the” torque level. To achieve good working results, press the power tool with sufficient force against the screw.

Handling the battery.
Store, operate and charge the battery only using FEIN battery chargers within the battery operating temperature range between 5 °C – 45 °C (41 °F – 113 °F). At the beginning of the charging procedure, the battery temperature must be within the battery operating temperature range.

The real percentage of the battery charge condition is only indicated when the power tool motor is stopped. The electronics automatically switch off the motor prior to the battery being deep discharged.

Repair and customer service

When working metal under extreme operating conditions, it is possible for conductive dust to settle in the interior of the power tool. Blow out the interior of the power tool via the ventilation slots frequently with dry and oil-free compressed air. Products that have come into contact with asbestos may not be sent in for repair. Dispose of products contaminated with asbestos according to the applicable country-specific regulations for such disposal. The current spares parts list for this power tool can be found on our website at www.fein.com.

If required, you can change the following parts yourself: application tools, depth stop, battery, belt clip.

Warranty and liability

The warranty for the product is valid in accordance with the legal regulations in the country where it is marketed. In addition, FEIN also provides a guarantee in accordance with the FEIN manufacturer’s warranty declaration. The delivery scope of your power tool may include only a part of the accessories described or shown in this Instruction Manual.

Declaration of conformity.
This CE declaration is only valid for European Union and EFTA (European Free Trade Association) countries and only for products intended for the EU- or EFTA market. After placing the product on the EU market the UKCA mark loses its mark validity. The UKCA declaration is only valid for the Great Britain market (England, Wales and Scotland) and only for products intended for the Great Britain market. After placing the product on the Great Britain market the CE mark loses its mark validity.  FEIN declares itself solely responsible for this productconforming with the relevant provisions given on the last page of this Instruction Manual. Technical documents at: C. & E. Fein GmbH, D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories should be sorted for environmental-friendly recycling. Dispose of batteries only when discharged. For batteries that are not completely discharged, insulate the terminals with tape as a protective measure against short-circuiting.

This CE declaration is only valid for European Union and EFTA (European Free Trade Association) countries and only for products intended for the EU- or EFTA market. After placing the product on the EU market the UKCA mark loses its mark validity.

  • DIN EN 62841-1:2015 + AC2015
  • DIN EN 62841-2-2:2014 + AC:2015
  • DIN EN 55014-1:2017 + A11:2020
  • DIN EN 55014-2:2015
  • DIN EN 55014-2:1997+A1:2001+A2:2008+AC:1997 2006/42/EG, 2014/30/EU, 2011/65/EU

The UKCA declaration is only valid for the Great Britain market (England, Wales and Scotland) and only for products intended for the Great Britain market. After placing the product on the Great Britain market the CE mark loses its mark validity

  • BS EN 62841-1:2015 + AC2015
  • BS EN 62841-2-2:2014 + AC:2015
  • BS EN 55014-1:2017 + A11:2020
  • BS EN 55014-2:2015
  • BS EN 55014-2:1997+A1:2001+A2:2008+AC:1997 Supply of Machinery Regulations 2008,

EMC Regulation 2006, The Restriction of the Use of Certain Hazardous Substances ln Electrical and Electronic Equipment Regulations 2012

FEIN Service
C. E. Fein GmbH
Hans-Fein-Straße 81
D-73529 Schwäbisch Gmünd-Bargau
www.fein.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals