Ciro Goldstrike Adjustable Toe Rests Instruction Manual

: June 13, 2024
: Ciro

Table of Contents

Golds trike Adjustable Toe Rests
Parts Included:
INSTALLATION:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Golds trike Adjustable Toe Rests
Instruction Manual

Golds trike Adjustable Toe Rests

Ciro Goldstrike Adjustable Toe Rests - circled Golds trike™ adjustable toe rests

Parts Included:

1 Left main mount
1 Right main mount
1 Left slider mount
1 Right slider mount| 2 U-Clamps
2 Toe rest arms
2 M8 x 1.25 x 70mm SHCS
2 M8 x 1.25 x 25mm SHCS| 2 M8 ﬂat washers
2 M6 x 1.0 x 20 mm hex head screw
4 M6 ﬂat washers
6 M6 x 1.0 x 20mm SHCS
---|---|---

INSTALLATION:

CAUTION: Gold strike recommends a thread locking ﬂuid such as 3M Scotch- Weld TL-43 for this installation.

Park on a level surface and shut oﬀ the motorcycle. Lift motorcycle onto its center stand if available. Ensure the engine has time to cool before installation.
Remove the plastic fog lamp cover and engine cover per owner’s manual. After removing the fog lamp cover and screws, the engine cover is removed by undoing a clip under its front edge. Next, pull out the rear and center darts. Finally, slide the cover forward to release a plastic hook near the front. Be patient and gentle. It will come oﬀ with very little force. (Fig. 1)
Remove the bottom engine guard bolt. (Fig. 2)
Install the right main mount where you removed the factory bolt in step 2. Use the 70mm long M8 screw and ﬂat washer included in the kit. Leave this loose for now. (Fig. 3)
Install the U-clamp around the black crash bar using the M6 hex head bolt with M6 ﬂat washer (circled in green) and the M6x1x20mm screw with M6 ﬂat washer (circled in blue). TORQUE: 8 N-m (0.8kgf-m 5.9lbf-ft)
Tighten the M8 screw (circled in red). TORQUE: 27 N-m (2.8kgf-m, 20lbf-ft) (Fig. 3)
Slide the right slider mount onto the main mount and use 2 M6x1x20 screws (circled in blue) to secure it in your desired location. TORQUE: 8 N-m (0.8kgf-m 5.9lbf-ft) (Fig. 4)
Install the engine cover. Start with the front lower corner ﬁrst, ensuring the plastic hook in engaged correctly. then pop the center dart into place and reinstall the screws. (Fig.5)
Repeat steps 2-8 on the other side.
Install the toe rest arms and adjust to the ideal position. TORQUE: 22 N-m (2.2 kgf-m 16 lbf-ft) (Fig.6)

ATTENTION: Keep the toe rest angle between 10 and 2 o’clock to maintain good ground clearance. If more adjustment is desired you can move the slider (Fig.4) accordingly. Ciro Goldstrike Adjustable Toe Rests - circled in
red2

WARNING:
This indication alerts you to the fact that ignoring the contents described herein can result in potential serious injury or death if not followed.
CAUTION:
This indication alerts you to the fact that ignoring the contents described herein can or will result in material damage and/or personal injury.
ATTENTION:
This indication alerts you to the fact if you ignore this detail you will act the performance or functionality of the product.
All Ciro products are designed for “easy assembly” and/or “plug and play”. We recommend a competent mechanic install our products, using standard mechanical procedures to assure a safe and successful installation.
NOTE: Ciro products are designed and manufactured under very strict quality control. Ciro warrants that products sold to the original purchaser shall be free from any defects in materials and workmanship for a period of 3 (three) years from the date of purchase, and a lifetime warranty against LED failure. Ciro will have no obligation if the customer cannot show proof of purchase. Warranty will not be granted unless the part is properly installed and maintained. Ciro will not be liable for any consequential and incidental damages, including labor, or non-Ciro products. Please visit our website Ciro3d.com for our complete warranty policy.