FEIT Electric LED Smart Camera Panel Light with Pan and Tilt Instruction Manual
- June 6, 2024
- Feit Electric
Table of Contents
FEIT Electric LED Smart Camera Panel Light with Pan and Tilt Instruction Manual
Safety Information
IMPORTANT SAFEGUARDS:
ALWAYS FOLLOW BASIC SAFETY PRECAUTIONS WHEN USING ELECTRICAL PRODUCTS,
ESPECIALLY WHEN CHILDREN ARE PRESENT.
Supplier’s Declaration of Conformity: 47 CFR § 2.1077 Compliance
Information
Responsible Party: Feil Electric Company 4901 Gregg Road, Pico Rivera, CA
90660, USA 562-463-2852
Unique Identifier: ADJ/CAM/PAN/WIFI/LED
This device complies with part 15 of the FCC Rules. Operation is subject lo
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Note: This
equipment has been tested and found to Comply with the limits for a Class B
dig Ital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential install/Ilion. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference lo radio or
television reception, which can be determined by bumping the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver, Connect the
equipment into en outlet on a circuit different from that to which the
receiver is connected. Consult the dealer or an
experienced radio/TV technician for help. Airy changes or modifications not
expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
The device has been evaluated to meet general RF exposure requirement
The device can be used in mobile (min 7.87 in.) exposure condition without
restriction.
Limited Warranty
This product Is warrantied to be free from defects In workmanship and materials for up to 1 year from date of purchase. If the product fails within the warranty period, please visit Feil. can’t/help for instructions on replacement/refund or call 866.326.BULB. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. UABIUTY FOR INCIDENTAL OR C0riSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply lo you. this warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
Pre-Assembly
HARDWARE INCLUDED
Description
Installation
-
Installing the smart camera panel light
Turn off the light switch before installing. Screw in the Smart camera Panel Light (AA) clockwise into an E26 socket until it is fully secure.
-
Mounting the safety cable
Drill a hole if installing on a surface such as drywall or concrete. Insert the Mounting Anchor (EE) into the hole. Screw in the Mounting Screw Eye Hook (DD) to the Mounting Anchor (EE). Secure the carabiner clips from the Safety Cable (CC) to the Mounting Screw Eye Hook (DD) and Smart Camera Panel Light (AA).
-
Adjusting the panel lights
Carefully push each individual light panel upwards until desired lighting angle is achieved.
-
Adjusting the camera in app
Turn ON the light switch. Add the device to the Felt Electric app (see the App Setup section). In the app, use the Direction pad or move the screen with your tinge(s) to pan(s) or tilt the camera until the desired viewing angle is achieved.
APP Setup
Downloading and Installing the Felt Electric app
- Search for the Feit Electric app in the App Store or Google Play Store.
- Download and install the Feit Electric app on your smart device.
- Connect to a 2.4GHz Wi-Fi network that covers your installation location.
Setting Up the Smart Camera Panel Light using the Feit Electric App
- 1. Check to be sure the camera is in pairing mode. The RED status light must be blinking rapidly to connect. If the light is not already blinking, press and hold the Reset Button until you hear an audible tone. Use the Feit Electric app to complete the setup.
- Tap Add Device or the+ sign. Tap Security & Camera and then select Camera. You will be prompted to enter your Wi-R network and password.
- Follow the directions in the Feit Electric app to pair your device using the QR code
- You can find more pairing methods in the dropdown menu on the device set-up page.
Need Help?
Thank you for your purchase. Questions, comments or feedback?
We’d love to hear from you. Visit feit.com/help for
support or connect with us:
Troubleshooting
SD™, microSD™, and SDHC™ are trademarks or registered trademarks of SD-3C, LLC
In the United States, other countries, or both.
FEIT ELICTRIC COMPANY I PICO RIVERA, CA | www.felt.com
RF exposure statement
This equipment meets the exemption from the routine evaluation limits in section 2.5 of Rss-102. It should be installed and operated with and operated with a minimum distance of 20cm between the radiator and any part of your body.
IC WARNING
This device contains licence-exempt transmitter(s) that comply with
Innovation, Science and Economic Development Canada Licence-exempt RSS(s).
Operation is subject to the following tow condition.
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>