Senao Networks Inc PCE2310M WiFi 6 User Manual

User Manual

• Product Name: WiFi 6 ax1800 2×2 dual concurrent M.2 B key Module
• Model Name: PCE2310M
• FCC ID: U2M-PCE2310M

Hardware Design Specification

PCE2310M module had been designed to replace ancient ac1200 dual concurrent PCIE module with M.2 B key which would be applied on SDWAN devices for networking with client device via wireless. M.2 B key design would also be compatible with existing 5G module slot.

1.1 Major Components

1.2 WiFi Specification (2.4GHz/5GHz)
Based on the transmit power (Tx) and receive sensitivity (Rx) specifications of MT7975DN, we conclude Tx power from chips and summarize Rx specification as the following table.

1.3 Power Consumption
The max power consumption is around 7.51W.
PCB Dimensions/Layers.

1.4 Support driver
PCE2310M is an integrated module on customer’s system board. The selected SDK or driver would be discussed and be negotiated firstly.
According to initial validation from Seano, we successfully brought up this module on existing NXP and AMD platform.

1.5 Compliant Regulatory
The planned certification domain would be covered following regulatory.
1.5.1 Tier 1 Compliant Regulatory

Countries/Regions| RF Standards| EMC Standards| Safety Standards
---|---|---|---
USA| OET Bulleting 65/Part 2.1093
FCC Part 15.247
FCC Part 15.407| FCC Part 15, Subpart B Class B| N/A
EU| EN 300 328 v2.2.2
EN 300 440
EN 301 893 v2.1.1 EN 50385: 2017
EN 301489-1/-17 v3.1.1| CISPR 32:2012 EN55032:2012 CISPR 24:2010 EN55024:2010 EN55035| N/A

2. Warning statements
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged  to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used.
RF Exposure warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be  co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
USERS MANUAL OF THE END PRODUCT
In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio- frequency  exposure guidelines for an uncontrolled environment can be satisfied.
The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT
The final end product must be labeled in a visible area with the following ” Contains FCC ID: U2M-PCE2310M “.

This radio transmitter FCC ID: U2M-PCE2310M has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna  types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Antenna List

Note: The antenna connector is SMA Male type.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>