AMP 77138-01A Running Board Assembly Installation Guide
- June 13, 2024
- AMP
Table of Contents
77138-01A Running Board Assembly
Product Information: – Product Name: AMP Part # – Compatible
Vehicles: Ram 1500 (2013-2017) Crew Cab, Ram 2500/3500 (2013-2017)
Crew Cab – Installation Time: 3-5 Hours – Recommended Skill Level:
4 (Experienced) – Tools Required: Safety goggles, Measuring tape,
10 mm socket, 13 mm socket, 1/2 socket, Ratchet wrench and
extension, Wire crimpers, Wire stripper/cutter, 3/16 hex key wrench
(allen wrench), 4mm hex key wrench (allen wrench), Electrical tape,
Weatherproof caulking (silicone sealer), Silicone spray – Warranty:
5-Year Limited Warranty – AMP Research Tech Support:
1-888-983-2204
(Press 2), Monday – Friday, 7:00 AM – 5:00 PM PST – Website:
www.amp-research.com Product Usage Instructions: 1.
Attaching motor to Linkage assembly: – Refer to the exploded view
in the manual for a visual representation. – Handle the components
with care. – Attach the motor to the Linkage assembly using the
provided Delta PT screws. 2. Running board assembly: – The running
board assembly consists of multiple components including Rail
Assembly, Motor Linkage assembly (Driver and Passenger), Idler
Linkage assembly, Wire harness, and Controller STA. – Follow the
provided diagrams and instructions to assemble the running board
components correctly. 3. Hardware Mounting Overview: – Locate the
forward most and rearward most mounting provisions on the inner
sill of the truck. – Remove tape from the sill drain hole at both
mounting points. – Note: Some vehicles may already have Front
welded fasteners installed. In such cases, backing plates and rivet
nuts are not needed for those locations. Factory Rivet nuts will
need to be removed to install backing plates. – Install the Driving
Linkage Assemblies (with motor) in the front mounting provisions
and the Idler Assemblies in the rear mounting provisions. 4. Set
Reinforcement Plate in place: – Drill a hole using a 1/8 drill bit
where the Reinforcement Plate needs to be placed. – After drilling,
apply paint to prevent rusting. – Insert a piece of string or wire
through the hole in the Reinforcement Plate and set the plate into
position. 5. Set rivet nuts into place for alignment: – Insert pop
rivets through the holes in the plate and secure them in place. –
Once the pop rivets are installed, remove the string or wire from
the Reinforcement Plate. – Verify that the plate is pulled flush to
the body before securing the pop rivets. Please refer to the
complete user manual for detailed instructions, diagrams, and
additional information on installation and usage.
INSTALLATION GUIDE
®
APPLICATION
TM
AMP Part #
Ram 1500 Ram 2500/3500
Crew Cab Crew Cab
2013-2017 2013-2017
77138-01A 77138-01A
Note:The application works only on the Crew Cab model Vehicles.
INSTALLATION TIME
3-5 Hours
Professional installation recommended
SKILL LEVEL
123 4
4= Experienced
TOOLS REQUIRED
q Safety goggles q Measuring tape q 10 mm socket q 13 mm socket q 1/2″ socket
q Ratchet wrench and extension q Wire crimpers q Wire stripper / cutter q
3/16″ hex key wrench (allen wrench) q 4mm hex key wrench ( allen wrench ) q
Electrical tape q Weather proof caulking (silicone sealer) q Silicone spray
WARRANTY 5-Year Limited Warranty
AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2) Monday – Friday, 7:00 AM – 5:00 PM PST
Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one OR MORE of the following patents: 6,641,158; 6,830,257; 6,834,875; 6,938,909; 7,055,839; 7,380,807; 7,413,204; 7,398,985; 7,584,975; 7,566,064; 7,487,986; 8,157,277; 8,408,571; 9,302,626; 9,561,751; 10,053,017; CA2463717 ©2012 AMP Research. All rights reserved. Printed in USA.
www.amp-research.com
1/12
IM77138 rev 01.24.23
AMP RESEARCH POWERSTEPTM Ram Crew Cab
INSTALLATION GUIDE Attaching motor to Linkage assembly.
EXPLODED VIEW
Motor Linkage Motor Kit Delta PT screws
CAUTION: HANDLE WITH CARE.
To ensure our customers receive all components with full integrity, we pack
the motors separate from their linkage assemblies. This requires that the
installer position and fasten the motor before continuing with the install.
Please follow the instructions below and handle the assembly carefully.
CAUTION: Dropping the assembly or any excessive impact MAY cause damage to the
motor. Instructions: 1. Position the gear cover in place as shown if not
already in place. 2. Seat motor into position on the three mounting bosses.
This may require an adjustment of the gear by moving the swing arms. 3. After
seating into place, fasten the motor with the three motor mount screws with
4mm Hex Head. Tighten screws to 36 in-lbs (4N-m). Do not over torque.
www.amp-research.com
2/12
IM77138 rev 01.24.23
AMP RESEARCH POWERSTEPTM Ram Crew Cab
A F
(A) End cap left (x1)
(B) End cap right (x1)
(C) T-nut insert (x2)
(D) Socket cap screw (x2)
1 x2
(E) End cap wedge right (x1) (F) End cap wedge left (x1)
Running board assembly
CE
BD
2 x2
Rail Assembly
3
Motor Linkage assembly Driver
4
Motor Linkage assembly Passenger
5
x2 Idler Linkage assembly
6
Wire harness
7
Controller STA
www.amp-research.com
8 x2
Posi-LockTM
3/12
9 x16
10 x12
M8 Hex Bolt w Conical washer
5/16-18 Flange Nut
IM77138 rev 01.24.23
AMP RESEARCH POWERSTEPTM Ram Crew Cab
11 x6
M5 Hex Bolt
12 x6
M5 Washer
13 x4
14 x4
M6 Flange Bolt 5/16 Flange Bolt
15 x8
Socket Cap Screw
16 x12
5/16-18 Carriage Bolt
17 x8
1/4-20 Flange nut
18 x8
Rivet Nut
19 x8
Button Head Torx Screw
20 x8
Washer
21 x4
Reinforcement Bracket
22 x4
Upper Mount Spacer
23 x4
Blind Rivet
24 x20
Cable tie (7″)
25 x2
Cable tie (11″)
www.amp-research.com
26 x4
LED Lamp
27 x8
Butt Connector
4/12
28
Rivet Nut Tool
IM77138 rev 01.24.23
AMP RESEARCH POWERSTEPTM Ram Crew Cab
29 x4
LED Light Bracket
30
OBD II Plug
31 x2
Motor kit
32
Linkage Mounting Bracket Passenger (Front)
33
Linkage Mounting Bracket Driver (Front)
34
Rail Mounting Bracket Passenger (Rear)
www.amp-research.com
35
Rail Mounting Bracket Driver (Rear)
5/12
IM77138 rev 01.24.23
AMP RESEARCH POWERSTEPTM Ram Crew Cab
HARDWARE MOUNTING OVERVIEW (passenger side shown)
Locate forward most and rearward most mounting provisions on inner sill of
truck. Remove tape from sill drain hole at both mounting points.
Note: Some vehicles may have Front welded fastners installed already. Backing plates and rivet nuts are not needed on these locations. Factory Rivet nuts will need to be removed to install backing plates.
1
Driving Assembly
Front
Idler Assembly
NOTE: Driving Linkage Assemblies (with motor) mount in the front; Idler Assemblies mount in the rear.
Set Reinforcement Plate in place and locate with rivet nuts. Drill hole using an 1/8″ drill bit. After drilling apply paint to prevent rusting
Once hole is drilled insert a piece of string or wire through hole in Reinforcement Plate. Set plate into position.
2
Set rivet nuts into place for alignment. Insert pop rivet through hole in
plate and secure in place. Once pop rivet is installed remove string or wire
from Reinforcement Plate. NOTE: Verify plate is pulled flush to the body
before securing pop rivet.
Assemble Hex Bolt (lubricated with soapy water), Washer, Rivet Tool, and Rivet Nut together as shown and place into hex cutouts in sill. An extra Hex Bolt and M8 Washer is supplied to install rivet nuts.
3
www.amp-research.com
4
6/12
IM77138 rev 01.24.23
AMP RESEARCH POWERSTEPTM Ram Crew Cab
With Rivet Nut Tool held in place with 19mm wrench, tighten Hex Bolt until Rivet Nut deforms and secures itself to the sheet metal (110 in-Lbs. or 4 turns). Remove Hex Bolt and Rivet Nut Tool. Repeat for each of the four mentioned mounting locations.
Once rivet nuts are in place use a screwdriver to push back tab in hole to avoid interference with linkage mount.
WARNING: Rivet Nuts not properly collapsed will not hold securely to sheet metal.
NOTE: Hold Rivet tool with
5
wrench while loosening bolt.
6
On Passenger side install Rear Rail Mounting Bracket (34) and Front Linkage Mounting Bracket (32) using the Hardware provided. 4 Conical washer bolts (9), 4 Button Head Torx (19), washers (20) and Flange Nuts (17). Once bolts are tightened up to vehicle torque Conical washer bolts (9) to 16 ft-lbs and Button head Torx to 6ft-lbs. Repeat on Driver side using rear bracket (35) and front bracket (33).
9 9
7
17,19&20
17,19&20
Insert and position 6 Carriage bolts (16) into slot on rail (4). Insert from either end of rail. Using Flange Nuts (10) provided assemble rail to Brackets using the 2 outer bolts on each side. Next install Flange Bolt (14) and Flange Nut (10) onto bracket tab. Torque flange nuts to 16ft-lbs. Install Light Bracket (29) using Flange Nut (10), leave loose to allow for adjustment. Driver side shown. Dimensions shown are for reference.
16
29
1106 1143
10
1106 & 176 Note: Badge on rail sits towards the rear of the vehicle!
8
www.amp-research.com
7/12
106 & 1176
IM77138 rev 01.24.23
AMP RESEARCH POWERSTEPTM Ram Crew Cab
Thread supplied bolts 2x (9) into Front Drive Linkage. Repeat step for Rear Idler Linkage. Do not tighten.
Install provided spacer (22) and M6 bolt (13) into upper mount as shown on
both the Drive and Idler linkages. Do not tighten.
13 22
98
8
19 14
91
Slide mounting T-nut into position, Center board in rail pocket. Tighten
fasteners to 10 ft-lbs.
9
10
Using a 13mm socket Torque linkage bolts 4x (9) from step 3 to 16 ft-lbs. Next
use a 10mm socket, torque linkage spacer bolt 2x (13) from step 6 to 8 ft-lbs.
Once linkages are tight cycle board to verify steps deploy under own weight.
143 2129
11
Once linkages are tightened to the bracket tighten bracket tab Flange bolt
(14) and Nut (17). Torque to 16 ft-Lbs.
12
8
Attach motor to linkage. Using a 4mm hex Torque to 36 in-Lbs.
167 143
153
www.amp-research.com
114
8/12
IM77138 rev 01.24.23
AMP RESEARCH POWERSTEPTM Ram Crew Cab
Prepare large tie-wraps (25) for mounting Power Step Controller (7). Loosely loop tie-wraps around large bundle of wires behind battery in engine compartment.
Insert controller (7) into tie-wrap loops and cinch down securely. The tie- wraps (25) should cinch down into channels on controller surface.
26 7
115
Remove fuse from Power Step Wire Harness.
16
Connect power leads from Controller, Red to positive battery terminal and
Black to the vehicle body ground as shown.
6
6
17
158
Locate large rubber wire boot on driver side firewall as shown below. Slice
small opening as shown
below to run trigger wires through.
Tape leading end of wires together and push through rubber boot to cabin side of the firewall. Silicon lubricant may be used for ease of passage. The trigger wires will come out just above and to the left of the brake pedal.
159
www.amp-research.com
250
9/12
IM77138 rev 01.24.23
AMP RESEARCH POWERSTEPTM Ram Crew Cab
Route the two Wire Harness legs down over the wheel wells toward Motor Linkages, long leg across to the passenger side. Secure harness with tie wraps.
Connect harness to motor. Secure harness with tie wraps.
4
211
22
Affix LED lamp (26) to Light bracket (29) on rail. Slide bracket into desired position and tighten using 5/32″ Allen key.
23
5
Using supplied butt connectors (27), connect the lamp wires. Red to Red, Black to Black. Once Crimped use heat gun to shrink tube. Close and wrap conduit with electrical tape. Secure all loose wires with cable ties. Pull lamp wires upward to avoid any wire snagging.
254
www.amp-research.com
10/12
IM77138 rev 01.24.23
AMP RESEARCH POWERSTEPTM Ram Crew Cab
OBD II install: Use Supplied Posi Twist connectors to attach the Plug and Play
Module to the Harness. Attach matching colors on the harness to the wires on
the module. Plug in module to OBD II port on the vehicle. Secure harness with
supplied tie wraps.
Note: If the OBD II pass thru harness (76404-01A) was purchased see install
sheet supplied in packaging. The pass through harness allows for an open port
for other accessories. See next page for a brief description.
OBD II Connector located below steering column.
To Powerstep Motors
To Vehicle Power (12V)
Powerstep Control Module
Vehicle Port
Powerstep Connection Module
Direct to Port Option
To Vehicle Power (12V)
To Powerstep Motors
25
www.amp-research.com
Powerstep Connection Module
Powerstep Control Module
Vehicle Port
Pass-Through Harness Option
Vehicle Port Pass-Through Harness (pin-topin at each terminal)
New Vehicle Port (replaces original port)
11/12
IM77138 rev 01.24.23
AAMMPP RREESSEEAARRCCHH PPOOWWEERRSSTTEEPPTTMM RRaamm CCrreeww CCaabb
Check that all doors activate the Power Step and the LED Lights work when
doors open and close. Reinstall any remaining trim panels.
FINAL SYSTEM CHECK Check that all doors activate the PowerStep and the LED
lights work when doors open and close. NORMAL OPERATION: When the doors open,
PowerStep automatically deploys from under the vehicle. When the doors are
closed, PowerStep will automatically return to the stowed/retracted position.
Note that
there is a 2-second delay before the PowerStep returns to the stowed/retracted
position. CORRECT OPERATION OF LIGHTS: All four lamps will illuminate upon
opening any door of vehicle. Lamps will stay on until restowing of both Power
Steps or until 5 minutes has expired with the doors open. When the lights
timeout after 5 minutes, they can be reillumintated by closing and opening any
door of vehicle.
3276
www.amp-research.com
12/12
IM77138 rev 01.24.23
TM
AMERICAN DESIGNED, ENGINEERED AND MANUFACTURED.
Thank you for your recent AMP Research Purchase.
REGISTER YOUR PRODUCT TODAY FOR FASTER SERVICE & PRODUCT UPDATES
Please visit: www.amp-research.com/productregistration or scan the QR Code
Product Registration Benefits:
· Ensure we have your purchase receipt and product info in our system which is
required for warranty
· Faster and easier access to customer service and tech support in the
unlikely event you need warranty or product support
· Registration helps us keep you up to date on product information and offers
To view other Amp Research products that may be offered for your vehicle.
Please visit: www.amp-research.com
Rev 01.05.21
TM
Congratulations on your purchase of the
genuine AMP Research PowerStep!
Here’s what you should know…
AMP Research PowerStep running boards automatically move when the doors are
opened to assist entering and exiting the vehicle.
Automatic power deploy: The running boards will extend down and out when the
doors are opened.
Automatic power stow: The running boards will return to the stowed position
when the doors are closed. There will be a 2-second delay before the running
boards move to the stowed position.
Automatic stop: If an object is in the way of the moving running board, the
running board will automatically stop. To reset, clear any obstruction, then
simply open and close the door to resume normal operation.
Manually set in the deployed (OUT) position for access to the roof:
your foot while at the same time closing the door. To resume normal operation,
open and close the door.
Maintenance: In adverse conditions, debris such as mud, dirt, and salt may
become trapped in the running board mechanism, possibly leading to unwanted
noise. If this occurs, manually set the running boards to
Avoid spraying the motors directly. After washing, apply silicone spray
lubricant to the hinge pivot pins. Do not apply silicone, wax or protectants
like Armor All® to the running board stepping surface.
Caution! Keep hands away when the running board is in motion.
5-YEAR LIMITED WARRANTY
AMP RESEARCH warrants this product to be free from defects in material and
workmanship for FIVE (5) YEARS FROM DATE OF PURCHASE, provided there has been
normal use and proper maintenance. This warranty applies to the original
purchaser only. All remedies under this warranty are limited to the repair
replacement of the product itself, or the repair or replacement of any
component part thereof, found by the factory to be defective within the time
period specified. The decision to repair or replace is wholly within the
discretion of the manufacturer.
for instructions. You must retain proof of purchase and submit a copy with any
items returned for warranty work. Upon completion of warranty work, if any, we
will return the repaired or replaced item or items to you freight prepaid.
Damage to our products caused by accidents, fire, vandalism, negligence,
misinstallation, misuse, Acts of God, or by defective parts not manufactured
by us, is not covered under this warranty.
ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
PURPOSE CREATED HEREBY ARE LIMITED IN DURATION TO THE SAME DURATION AND SCOPE
AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL NOT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGE.
Some states do not allow limitations on how long an implied warranty lasts, or
the exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights that vary from state
to state. FOR WARRANTY ISSUES WITH THIS PRODUCT PLEASE CALL AMP RESEARCH TECH
SUPPORT 1-888-983-2204
WARNING
Be sure to read and precisely follow the provided instructions when installing
this product. Failure to do so could place the vehicle occupants in a
potentially dangerous situation. After installing or reinstalling, re-check to
insure that the product is properly installed.
The material that your product is made from can be recycled. Please also
consider recycling the packaging
that your product came in.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>