Fusion DSP313 OLED Display User Guide

: June 13, 2024
: FUSION

Fusion DSP313 OLED Display

Fusion OLED Display, a brief introduction

Thank you for purchasing the Fusion OLED Display.

The Fusion OLED Display can be used in combination with:

All Fusion Amps
DSP313 */*
( OEM only)
(** Previously called MP-DSP Main)

Please read the safety instructions on the next page before assembling and installing and/or operating the Fusion OLED Display.

This assembly instruction covers the general assembly instructions for the Fusion OLED Display.

Contents of packaging:

1x Fusion OLED Display
1x Cable Z5C125L1
All required mounting materials
This assembly instruction

Safety precautions

Damage due to inappropriate handling is not covered by warranty. This product has no user-serviceable parts.

Warning: To reduce the risk of fire or electric shock, do not expose this device to rain or moisture.

Attention: Observe precautions for handling electrostatic sensitive devices. This module uses semiconductors that can be damaged by electrostatic discharge (ESD).

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the prescence of uninsulated “dangerous voltage” within the product’s enclosure, that may be of significant magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user of the prescence of important operating and maintaining (servicing) instructions in the literature accompanying the appliance.

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Only use this attachment/accessory as specified by the manufacturer.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as signal cable or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
This apparatus shall not be exposed to dripping or splashing, and no object filled with liquids, such as vases or beer glasses, shall be placed on the apparatus.
Do not run any cables across the back off the module. Apply fixtures to cables to ensure that this is not compromised.
Before using this product, ensure the cable is correctly connected not damaged. If you detect any damage, do not use the product.
Changes or modifications not expressly approved by Hypex Electronics will void compliance and therefore the user’s authority to operate the equipment.
Service or modifications by any person or persons other than by Hypex Electronics authorized personnel voids the warranty.

Correct disposal of this product: This symbol indicates that this product should not be disposed of with your household waste, according to the WEEE directive (2012/19/EU) and your national law. This product should be handed over to an authorized collection site for recycling waste electrical and electronic equipment (EEE). Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, or your household waste disposal service.

Parts

Details

Protective foil
IR remote receiver
Transparent display area
Cable entry to DSP
Adhesive tape
Flex-cable

Dimensions (mm)

Preparations, mounting and connecting

Connections

Remote Control

IR transmitter
Power on/off
Preset 1
Preset 2
Preset 3
(not used)
Input previous
Input next
(not used)
Volume +
Volume –
Mute

Rc5 Codes supported by Fusion Amp (Device code: 16)

Code| Fusion Amp Function| Hypex Remote| Code| Fusion Amp Function| Hypex Remote
---|---|---|---|---|---
34| Reserved| Internal use| 61| Reserved| F4
48| Reserved| OK| 18| Analogue XLR| –
50| Power ON/OFF| ON/OFF toggle| 19| Analogue RCA| –
51| Volume UP| Arrow Up| 20| Analogue High Level Input| –
52| Volume DOWN| Arrow Down| 21| SPDIF (digital RCA)| –
53| Mute| Mute| 22| AES (digital XLR)| –
54| Select next input| Arrow right| 23| Toslink| –
55| Select previous input| Arrow left| 24| Future option| –
56| Select preset 1| F1| 25| Reserved| –
67| Select preset 2| F2| 28| Reserved| –
59| Select preset 3| F3| 29| Reserved| –

Notifications

Default

Feedback

Source

Notice

Firmware Update

To update the display with the latest firmware it can manually downloaded from our website and uploaded to your device using the Display update function in HFD.
For instructions and the latest procedures please check out the latest FA Update Tutorial which can be found at: www.hypex.nl/faq/ Q: How to update my Fusion Amp Firmware?

Settings

HFD provides the possibility to adjust the brightness of your display.

Options:

Active brightness (0-15)
Idle screen brightness (1-15 / 0 = OFF)

HFD

Make sure the Fusion Amp is powered on.

Connect it with USB to the computer.

Open the latest HFD (v4.97 or higher) and press Device settings.

Device settings

The Display settings are situated in the Options section.

will set the brightness of the display during activities.

will set the brightness during idle.

OLED displays are very sensitive to burn-in symptoms, such as permanent discoloring, if white or brightly coloured logos are used at high brightness levels. To avoid burn-in symptoms, we recommend that you set the level to 6 or lower.

Adjustments

Adjustments are directly Brightness implemented and don’t need saving to be retained.
Make the adjustments by pressing the dots situated left (down) and right (up) or by selecting the number and filling in the desired value.

Most of the time the idle screen will be shown during adjustments so in order to review the max setting you can activate the display with the remote control by altering the volume or other options during brightness

System information

Performance:
96×64 Pixels
65536 Colors

Dimensions and weight:

External size (WxHxD): 43 x 35 x 7,5 mm (excl connector

Total weight: 12,5 g (excl cable)

Remote:
RC5 IR sensor for Hypex Remote Control

Operation :
On all Fusion Amps
DSP313 (OEM only)

Frequently asked questions

Q How many Fusion OLED Displays can I use in a master and slave setup?
A You can use a Fusion OLEO Display with every Fusion amp in your chain. Basically you only need one at your master device. A FA slave will not respond to IR commands, but the display will function as expected.

Q I do not have any technical experience, can I install this display myself?
A Yes! Even without any technical experience you can install the display. Use this assembly instruction.

Q After turning off my Fusion Amp the display stays on for a couple of seconds, is this normal?
A Yes, this is normal. In order to shut down the system gracefully, the DSP and Display shut down time is delayed.

Q If I update the HFD software or firmware do I need to update the Display as well?
A No, updates for the display are separate.

Q Can I use a third party remote control?
A Yes, that is possible. Please refer to page 7 ,,Remote Control”.

Troubleshooting

No power

Check if your Fusion Amp or DSP is powered on.
Check if the Fusion OLED Display cable is connected correctly with your Fusion Amp or DSP.

Support

We continuously work to improve your experience with our products. If you have suggestions, remarks or found a bug, please contact us.

If you have any problem with your Fusion OLED Display please consult this assembly instruction.
If this assembly instruction is not sufficient in order to fix your problem please contact the Hype support department.

Visit our website!
The latest datasheets and manuals can be found there. Look into our FAQ and if you can not find the answer there, you can also contact us and we will be happy to assist you!

Limited Warranty

Hypex Electronics warrants this device for a period of two years (B2C) after the original date of purchase against defects due to faulty workmanship or materials arising from Normal Use of the device. The warranty covers working parts that affect the function of the device. It does NOT cover cosmetic deterioration caused by fair wear and tear, or damage caused by accident, misuse or neglect. Any attempt to modify or take apart the device (or its accessories) will void the warranty.

If you discover a defect, notify Hypex Electronics during the warranty period. Claims under warranty must be supported by reasonable evidence that the date of the claim is within the warranty period. To validate your warranty, please keep your original purchase receipt together with these warranty conditions for the duration of the warranty period. Replacement products claimed under warranty are not entitled to renewed 2-year warranty coverage.

Date of purchase:

Disclaimer

Hypex Electronics BV, its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,“Hypex Electronics”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet, user guide or in any other disclosure relating to any product.

This Fusion OLED Display is designed for use with Hypex Fusion Amp only. No representations are made as to fitness for other uses. Except where noted otherwise any specifications given pertain to this Fusion OLED Display only.

LIFE SUPPORT POLICY: Use of Hypex products in life support equipment or equipment whose failure can reasonably be expected to result in injury or death is not permitted except by explicit written consent from Hypex Electronics BV.