SATCO 65-781R2 LED UFO High Bay Instruction Manual

June 13, 2024
SATCO

LED UFO HIGH BAY
Models:
65-781R2, 65-782R2, 65-783R2, 65-784R2,
65-791R2, 65-792R2, 65-793R2, 65-794R2,
65-801R2, 65-802R2, 65-803R2, 65-804R2:
ø11″ (280±5mm)
65-784R2, 65-785R2, 65-787R2, 65-788R2,
65-795R2, 65-796R2, 65-797R2, 65-798R2,
65-805R2, 65-806R2, 65-807R2, 65-808R2:
ø13.4″ (340±5mm)

INSTALLATION AND SAFETY INSTRUCTIONS

IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING: Risk of Fire or Electric Shock

  • To avoid damage, falling, electric shock or fire, do not modify the lamp or replace accessories without confirming with the supplier first.
  • Only authorized, qualified personnel should install this fixture and should follow the owner’s manual. Any improper installation might cause failure, electric shock, fire or other injury, damage or hazard.
  • Disconnect power before installation or any maintenance of the fixture.
  • Do not dismantle the fixture without the supplier’s authorization.
  • Do not touch the power supply when the fixture is operating.
  • The external flexible cable or cord of this fixture cannot be replaced; if the cord is damaged, the fixture shall be destroyed.
  • Terminal block not included. The electrical fitting must be installed by a licensed electrician.
  • For use in environments where an accumulation of non-conductive dust on the fixture may be expected.

IMPORTANT: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.

SPECIFICATIONS

Model CCT   Volts Operating Temperature
65-781R2 4000K 100-277V -40°C to +45°C (-40°F to +113°F)
65-782R2 5000K
65-783R2 4000K
65-784R2 5000K
65-785R2 4000K
65-786R2 5000K
65-787R2 4000K
65-788R2 5000K
65-791R2 4000K
65-792R2 5000K
65-793R2 4000K
65-794R2 5000K
65-795R2 4000K 4000K -40°C to +45°C (-40°F to +113°F)
65-796R2 5000K 5000K
65-797R2 4000K 4000K
65-798R2 5000K 5000K
65-801R2 4000K 4000K
65-802R2 5000K 5000K
65-803R2 4000K 4000K
65-804R2 5000K 5000K
65-805R2 4000K 4000K
65-806R2 5000K 5000K
65-807R2 4000K 4000K
65-808R2 5000K 5000K

WIRING DIAGRAM & INSTRUCTIONS

The LED high bay light can be equipped with an optional DC motion sensor (86/218 microwave sensor, 86/217 – 6m mounting height or 86/220 -12m mounting height PIR sensors). The sensor needs to be set via remote (86/219). For standard 0-10V dimming applications, see wiring diagram.

SATCO 65 781R2 LED UFO High Bay - INSTRUCTIONS

INSTALLATION: Hook Mount
STEP 1: Screw the hook into the fixture, tighten and secure.

STEP 2: Hang the fixture on the ceiling hook or chain.

SATCO 65 781R2 LED UFO High Bay - fixture STEP 3: Connect wires using the wiring diagram and instructions on page 1. Make sure connections are capped and sealed.

INSTALLATION: Ceiling Mount
STEP 1: Use a pen or sharp tool and mark holes through the mounting surface on the ceiling and drill holes. Fix screws into the holes with a hammer.

SATCO 65 781R2 LED UFO High Bay - mounting

STEP 2: Align the bracket hole with screw hole nd push the fixture to one side and secure.

SATCO 65 781R2 LED UFO High Bay - mounting 2

STEP 3: Connect wires using the wiring diagram and instructions on page

  1. Make sure connections are capped and sealed.

NOTE: By adjusting the bracket screws, the fixture can be angled 50° to the left or right vertically.

Optional DC Motion Sensor
Motion sensor installation does not require tools.

NOTE: The motion sensor has no dialing code. A remote control (86/219) is needed for adjustment. Refer to remote control instructions for adjustments.

If motion sensor is not desired, unscrew the motion sensor and replace it with a protective cover.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals