HOME ACCENTS Holiday 1004363929 7.5 Foot Uptown LED Pre-Lit Tree Instruction Manual
- June 13, 2024
- HOME ACCENTS Holiday
Table of Contents
7.5 ft Uptown LED Pre-Lit Tree
SKU# 1004363929
Safety Information
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed
including the following:
a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 0.25 A 120 V 60
Hz.
c) Do not use seasonal products outdoors unless marked suitable for indoor and
outdoor use. When products are used in outdoor applications, connect the
rpoduct to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not
provided, contact a qualified electrician for piper installation.
d) This seasonal use product is not intended for permanent installation or
use.
e) Do not mount or place near gas or electric heaters, fireplace, candles or
other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, or when retiring for the night,
or if left unattended.
i) This is an electric product – not a toy! To avoid risk of fire, burns
personal injury and electric shock it should not be played with or placed
where small children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light string.
l) Do not close doors or windows on the product or extension cords as this may
damage the wire insulation.
m) Do not cover the product with cloth, paper or any material not part of the
product when in use.
n) Read and follow all instructions that are on the product or provided with
the product.
o) SAVE THESE INSTRUCTIONS.
Pre-Assembly
Package Contents
Assembly
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step 2. Open the stand to a 90 degree angle until the hole lines up with
the hole on the tube.
Step 3. Screw an eye bolt into the hole.
CAUTION! – ALWAYS UNPLUG YOUR TREE FROM ITS POWER SOURCE BEFORE
ASSEMBLING OR DISASSEMBLING.
Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Carefully insert bottom section (C) of tree into tree base and
tighten the screw. (See Fig. 1)
Step 2. Insert the middle section (B) of the tree into the bottom section
(C). (See Fig. 2)
Step 3. Insert the top section (A) into the middle section (B). (See Fig.
3)
Step 4. Connect the end connector of power cord with foot pedal switch
(E) with the connector found on the bottom section (C) in correct direction
(always match the protuberance on the end connector of power cord to the
concave on the connector found on the bottom section (C) according to the
magnified drawing. (See Fig. 4)
Step 5. Allow branches to fall into place or gently pull branches up and
out.
When adjusting branches be sure that all wires are free of branch hinges. (See
Fig. 5)
Step 6. Shape the branches. Starting with tips closest to the pole, shape
one tip to the right, one to the left and one at the center of the main stem.
Repeat pattern for each branch. (See Fig. 6)
Step 7. Plug the well-connected power cord from the tree section (C) into
a proper outlet.
Step 8. Please note this tree comes with a foot pedal switch and a remote
control for easy illumination and changing functions.
This tree is Color Changing, the 8 lighting options available are:
- Steady Warm White
- Flashing Warm White
- Fade In and Fade Out Warm White
- Steady Multicolor
- Flashing Multicolor
- Fade In and Fade Out Multicolor
- Sequential Multicolor & Warm White
- Color Changing
These functions can be changed by pressing the foot pedal switch or using the remote control. Please see the instructions of remote control below.
Operation
Turning on the tree
Step 1. Plug the well-connected power cord from the tree section (C) into
a proper outlet.
Step 2. Press the remote control or foot pedal switch to choose
functions.
Instructions of Remote Control
Please note this tree has a remote control.
Please pull out the insulation tape from the remote control, before starting
to use it.
- Press Fn button, the function below cycle. Press the number key, select from the following corresponding lighting functions:
Function 1: Steady Warm White
Function 2: Flashing Warm White
Function 3: Fade In and Fade Out Warm White
Function 4: Steady Multicolor
Function 5: Flashing Multicolor
Function 6: Fade In and Fade Out Multicolor Function 7: Sequential Multicolor & Warm White
Function 8: Color Changing
If the remote control does not work, check whether the battery of the remote control is out of power.
To replace the remote control battery:
- Replace with a new button cell “CR2025” (3 volt) into the compartment.
CAUTION: DO NOT DISPOSE OF
BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR LEAK.
CAUTION: The product consists of non-replaceable LED lamps. To reduce the risk of fire or electric shock, do not attempt to replace lamps or modify string.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the cord from the wall outlet and then disconnect each
section of the tree. Remove the power cords from the tree bottom (C).
Step 3. Gently lift the tree top straight up to remove from the center
section and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it
shut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
| Problem | Solution |
|---|---|
| The tree does not light | Ensure that all tree sections are connected into each |
other well by pressing each section down and rotating.
Ensure that the power cord is plugged into the hole of the connector found on
the tree bottom (C). Make sure power cord plug is securely inserted into a
working electrical outlet.
If you are still experiencing problems with the tree please call
1-877-527-0313 for instructions.
Warning: Please note that changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Adapter Model No. TS-12W12V
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>