HOME ACCENTS holiday 20090105061702H 50L Multi C9 LED Steady Lit Heavy Duty Lights Instruction Manual
- October 30, 2023
- HOME ACCENTS Holiday
Table of Contents
20090105061702H 50L Multi C9 LED Steady Lit Heavy Duty Lights
Instruction Manual MODEL NO. 20090105061701H/2H
SMT-S50/SC9
FOR INDOOR AND OUTDOOR USE LED22
IMPORTANT SAFETY INSTRUCTIONS
When using electric products, basic precautions should always be followed including the following:
a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for indoor and
outdoor use.
When products are used in outdoor applications; connect the product to a
Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided,
contact a qualified electrician for proper installation.
c) This seasonal use product is not intended for permanent installation or
use.
d) Do not mount or place near gas or electric heaters, fireplaces, candles or
other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
f) Do not let LEDs rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or
if left unattended.
h) This is an electric product not a toy! To avoid risk of fire, burns,
personal injury and electric shock, it should not be played with or placed
where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not place lighting string on carpeting, drapes, furniture, or allow it
to contact vinyl siding while the power is on.
l) Do not perform any maintenance or troubleshoot for bad or broken LEDs while
the power is on.
m) Do not close doors or windows on the product or extension cords as this may
damage the wire insulation.
n) Do not cover the product with cloth, paper or any material not part of the
product when in use.
o) This product is equipped with non-shunted type LEDs. Do not twist LEDs
after the reflector is removed.
p) This product employs overload protection (fuse). A blown fuse indicates an
overload or short-circuit situation. If the fuse blows, unplug the product
from the outlet. Also unplug any additional strings or products that may be
attached to the product.
Replace the fuse as per the user servicing instructions (follow product
marking for proper fuse rating) and check the product. If the replacement fuse
blows, a short-circuit may be present and the product should be discarded.
q) Read and follow all instructions that are on the product or provided with
the product.
r) Caution: To reduce the risk of fire and electric shock: a) Do not install
on trees having needles, leaves or branch coverings of metal or materials
which look like metal, and b) Do not mount or support strings in a manner that
can cut or damage wire insulation.
s) SAVE THESE INSTRUCTIONS USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well
maintained and fresh. Do not place on live trees in which the needles are
brown or break off easily. Keep the tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and
stable.
c) Before using or reusing, inspect product carefully. Discard any products
that have cut, damaged, or frayed wire insulation or cords, cracks in the LED
holders or enclosures, loose connections or exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is
placed, including tree branches, or bushes to avoid any undue strain or stress
on the product conductors, connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from
sunlight.
f) LEDs which become loose or burned out must be replaced promptly in order to
maintain the performance and life expectancy of this set.
g) Be careful not to drop the light set onto a hard surface.
USER SERVICING INSTRUCTIONS
Fuse replacement: Most often, fuses blow because too many sets have been
strung end-to-end.
a) Before changing fuses, make sure the set is unplugged.
b) Grasp plug and remove from the receptacle or other outlet deviceDo not
unplug by pulling on cord
c) Using a flathead screwdriver, open fuse cover. Slide open the
fuse access cover on top of attachment plug towards blades.
d) Remove fuses carefully.
e) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with
product).
f) Close fuse cover. Slide closed the fuse access cover on top of attachment
plug. Make sure door is fully closed and fuses are completely covered.
g) Risk of fire. Do not replace attachment plug. Contains a safety device
(fuse) that should not be removed. Discard product if the attachment plug is
damaged. LED replacement: Before changing LEDs, make sure set is unplugged.
Step 1: Grasp plug and remove from the receptacle or other outlet device. Do
not unplug by pulling cord.
Step 2: Unscrew plastic reflector from LED holder.
Step 3: If required, remove the plastic reflector over the LED.
Step 4: Replace LED with only 3.2 volt, 0.064 Watt LED type Lamp (provided
with product).
Step 5: Place the plastic reflector over the LED.’
Actual lamp cover may vary according to product purchased.
CAUTION:
- This lighting string is rated 7.8 Watts (0.065 Amps), do not overload. Connect other lighting strings or decorative outfits end-to-end up to a maximum of 216 Watts (1.80 Amps) total. If connecting to a lighting string that does not have a Wattage (W) rating {found on the tag within 6 inches of the plug} calculate the wattage as follows: Multiply the current (___A) which is on the flag-type tag by 120. For Example: Lighting string is rated 120V, 60Hz, 0.2 Amps. 0.2 X 120 = 24 Watts. Add the wattage of each light string together for a total of 216 Watts or less. (Do not exceed 216 Watts.)
- To reduce the risk of overheating, replace burned-out LEDs promptly. Use 3.2 Volt, 0.064 Watt LEDs provided with this product.
- Do not use a dimmer switch or install any additional Christmas lighting or ornamentation that is powered by a light bulb socket. Doing this may result in damage to your light string or cause personal injury. This action will result in a void of the limited warranty of this product.
- Risk of fire. This products does not contain shunts inside the lamps. Do not replace lamps with other than the spare lamps provide with this product.
TROUBLESHOOTING
If Lights are not working – Check the Glass Fuse located inside the plug. (See
diagram on this page on how to gain access to the Fuse inside the Plug). If
the metal filament inside the Glass Fuse is broken – Replace with spare fuse
provided in the accessory bag.
If product is still malfunctioning,
before returning call the Customer Service line:
1-855-HDHoliday (1-855-434-6543)
10 year limited guarantee. This product was pre-tested before shipment and
date coded. In keeping with the National Electrical Code, this product is
intended for seasonal (90 days max.) installation and use. HOME ACCENTS
Holiday LED lights 10 year guarantee covers repair or replacement of any
product that fails to light for 10 consecutive holiday seasons (90 days max.
per season). This guarantee is void if the product is misused or damaged in
any way. If product fails to light call Home Depot customer service toll-free
at 1-855-HDHoliday (1-855-434-6543).
DISTRIBUTED BY HOME DEPOT U.S.A., INC.
2455 PACES FERRY RD., N.W. ATLANTA, GA 30339
All rights reserved. 301004
MADE IN VIETNAM PRINTED IN VIETNAM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>