Jungborn 10530088 Wall Mounted Toilet Instruction Manual

: June 13, 2024
: Jungborn

Jungborn 10530088 Wall Mounted Toilet Instruction Manual

Read the instructions carefully before use and keep them for future reference! For daily cleaning use only commercial bath cleaners. Lime scale and soap residue can be removed with commercial lime remover or vinegar cleaners.

Assembly Instructions Wall-Mounted Toilet

Electrical work and repairs may only be carried out by qualified electricians.
The respective national installation regulations must be observed during installation.
The device must not be modified in any way. Electric shock and risk of accident.
Always make sure that the power supply is disconnected before installation.
If the power cord is damaged, it must be replaced by the manufacturer, its customer service or a similarly qualified person in order to avoid hazards

The appliances must be earthed.

Water Supply Pressure: 70000~750000Pa

The instructions concerning persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge and children playing with the appliance are not applicable.

Children being supervised not to play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision

The shower toilet set is used for comfortable cleaning and drying of the buttocks and vaginal area after using the toilet. Any other use automatically voids all liability and warranty claims.

Symbols used

Danger

plies with relevant safety standards

Protection class 1

Protection against splashing water on all sides

Cleaning

Before cleaning, always disconnect the unit from the power supply. Please use only commercially available cleaning agents and disinfectants and a soft damp cloth. Never use aggressive cleaners, scouring agents or products containing chlorine or solvents

Water drainage

In case of transport or disassembly, you must empty the unit

Turn off the water supply. Disconnect the appliance from the mains. Loosen the drain plug by turning it anticlockwise. Remove the drain plug and empty the appliance.
Please never turn the unit over before you have drained it. You may permanently damage the electronics
Water drainage

Replacing the limescale filter

The limescale filter is located in the supply line of the shower toilet and prevents the unit from becoming clogged with limescale deposits. The service life is 1/2 year on average, but this period is reduced if the water contains a lot of limescale. You can find out the respective degree of hardness from your public utility company. Replacement is necessary when the water pressure drops significantly. You can obtain further replacement filters from the dealer from whom you purchased the product.

Function overview

Remote control

Batteries not included

Rear spray / Front spray

Sit on the bidet. Press the “Rear spray” or “Front spray” button on the remote control; the bidet begins cleansing. Cleansing ends automatically after 3 minutes. You can also stop the cleansing process beforehand by pressing the “Stop” button

Dryer

Sit on the bidet. Press the “Dryer” button on the remote control; the bidet begins drying. Drying ends after 3 minutes. You can also stop the cleansing process beforehand by pres- sing the “Stop” button.

Pulse massage spray

Sit on the bidet. Start the “Rear spray” or “Front spray” programme. Then repeatedly press the “Massage” button on the remote control until you’ve reached your desired spray mode. The indicators on the remote control show the function.

Oscillating: 1 indicator lights up; Pulsating: 2 indicators light up;
Oscillating + Pulsating: 3 indicators light up

Adjusting the flow rate

Sit on the bidet. Start the “Rear spray” or “Front spray” programme. Press the “Adjusting the flow rate” button on the remote control and then the “Decrease” or “Increase” button to adjust the flow rate.

Adjusting the nozzle position

Sit on the bidet. Start the “Rear spray” or “Front spray” programme. Press the “Nozzle position” button on the remote control and then the “Decrease” or “Increase” button to move the position of the nozzle forward or backward. The preset position is 5

Adjusting the water temperature

Sit on the bidet. Start the “Rear spray” or “Front spray” programme. Repeatedly press the “Adjusting the water temperature” button on the remote control until the water tempera- ture symbol lights up. Then press the “Increase” or “Decrease” button to adjust the water temperature

Setting the night light

The default night light mode is “Always on”. Repeatedly press the “Night light” button on the remote control to toggle through the different modes. “Close” mode: One indicator lights up; “Always on” mode: Two indicators light up; “Smart” mode: Three indicators light up.
PLEASE NOTE: In “Smart” mode, the night light turns on when its dark and turns off when it’s bright

Setting the odour extraction

The standard deodorising mode is “Smart”. The odour extraction is switched on when the user sits down and switched off one minute after the user stands up. If no washing or drying function was activated while the user was seated, it is switched off after 15 minutes. Repeatedly press the “Odour extraction” button on the remote control to activate or deactivate the function. “Close” mode: One indicator lights up; “Smart” mode: Two indicators light up

Setting the sound

By default, the sound is on. A BEEP sounds when the bidet receives commands or signals. Press and hold the “Set temperature” button on the remote control and then press the “Front spray” button. Off: One indicator lights up; On: Two indicators light up

User settings

Saving user settings After adjusting the flow rate, temperature and nozzle position, press and hold the “User 1” or “User 2” button on the remote control for more than 3 seconds to save the settings for “User 1” or “User 2”. Activating user settings Before washing or drying, press the “User 1” or “User 2” button and then start washing or drying. The bidet activates the settings for flow rate, water temperature, nozzle position and air temperature saved for the active user.

Self-cleaning the water tank

PLEASE NOTE: If the appliance has not been used for more than 72 hours and a user using the washing function, the self-cleaning function activates for 30 seconds. During self-clea- ning, all buttons are inactive and will be reactivated after self-cleaning

Descaling

You need to descale the appliance at least once a year, or more often, depending on the number of cleaning cycles you’ve run and the quality of the water in your area. During de- scaling, you can continue to use the toilet, however, without the washing function. Descaling takes up to 30 minutes. During this time, the night light flashes continuously. When the night light stops flashing and the appliance emits a long beep, you can use the washing function again. Please use 150 ml of commercially available, non-foaming descaling agent.

Please note: Water flows out of the nozzle when the cover is opened.
The appliance emits two beeps to indicate that you can now pour in the descaling agent

Removing the bidet seat

Replacing the bidet seat hinge

Troubleshooting

Problem	Potential cause	Suggested action
The washing cyclus can not work	The power supply may not be opened	Please

turn on the power
The water supply may not be opened| Please open the inlet water valve, or check if there is a water outage
The filter may be blocked| Please replace a new filter .It has a service life of approx. half a year
Maybe not in the seating state| Please sit on the seat and adjust sitting position
Maybe the cover is closed| Please open the cover and sit on the toilet seat
Maybe it is not used for more than 72 hours| Not used for more than 72 hours ,when the user operates the washing ,it will open the self-cleaning for about 3 minutes. All the buttons are invalid during the self-cleaning and it will return to normal after the self-cleaning
The nozzle goes back suddenly| The washing cycle is 3 mins. The nozzle will stop spraying after 3 mins, and then go back.| This is normal and please re- press the “wash” button to start washing again
There may be some problems of water supply| Please check if there is a water outage
Maybe the seated sensor detects the user left the seat| Please adjust sitting position
Maybe the cover is closing| Do not put down the cover when it is washing
Low water flow rate| The water flow rate may be set at low grades| Please increase the flow rate as per “adjusting water flow rate” of operating instructions
The water supply pressure may be too low| Please check and ensure the water supply pressure is � 0.07 Mpa
The filter may be blocked| Please replace a new filter .It has a service life of approx. half a year
The nozzle may be blocked| Please replace a new nozzle
Low water tempera- ture| The water temperature may be set at low grades| Please set the water temperature at high grade as per “adjusting temperature” of operating instruc- tions
Maybe the temperature of water supply is too low| Please set the water temperature at high grade as per “adjusting temperature” of operating instruc- tions, or decrease the flow rate as per “adjusting water flow rate” of operating instructions.
The nozzle comes out slowly| When start washing function, the nozzle will be self-cleaning before coming out, and this will take some time| This is normal
The water flows out butthe nozzle do not come out| When start washing function, the nozzle will be self- cleaning before coming out . This functionalso takes place after the washing cycle.| This is normal
Maybe it is not used for more than 72 hours| This is normal. Not used for more than 72 hours ,when the user operates the washing , it will open the self- cleaning for about 3 minutes
The dryer can not work| The power supply may not be opened| Please turn on the power
Maybe not in the seating state| Please sit on the seat and adjust sitting position
Maybe the cover is closed| Please open the cover and sit on the seat
Maybe it is not used for more than 72 hours| Not used for more than 72 hours ,when the user operates the washing ,it will open the self-cleaning for about 3 minutes. All the buttons are invalid during the self-cleaning and it will return to normal after the self-cleaning
Low air tempera- ture| The air temperature may be set at low grades| Please set the air temperature at high grade as per “adjusting temperature” of operating instructions
The air heater can not work normally| Please contact local distributor
The remote con-trol is not functioning| Maybe there are not batteries in the remote control| Please install the correct batteries in the remote control
Maybe the battery power is too low| When the battery power is too low the LED of grade will flash. Please replace the battery
Maybe the code of the bidet and remote control is not the same| Set the remote control to the appropriate code (see page 28).
The bidet can not work normally| Maybe there is something abnormal| Please shut off the power and turn on after one minute. If the bidet still cannot work, please contact local distributor
There is constantly BEEP| The water supply temperature may be too high| Please shut off the power and water supply, stop using the product, and then contact local distributor

Nozzle cleaning

The nozzle is cleaned before and after washing. Open the lid and the seat, but do not sit on the bidet. Press and hold the “Set temperature” button on the remote control and then press the “–” button. The nozzle then extends with cleaning water. It returns automatically after 5 minutes, or you can press the “Stop” button.

Remote control teach-in

If you install several electronic bidets in the same area and you want each remote control to control the specified electronic bidet, please follow the steps below. The same procedure applies to teaching a new remote control.

Close the cover and the seat.
Simultaneously press the „Stop“ button and the „Set temperature“ button on the remote control and keep them pressed for a few seconds. hen a beep sounds and the indicator lights of the „-,+“ buttons light up.
Release the „Stop“ key but keep the „Set temperature“ key pressed.
Press the „USER1“ and „USER2“ keys in succession and then release the „Set temperature“ key. At this time, the display lights up with the current ID code of the product.
By pressing the „-, +“ buttons of the flow rate, you can switch between the different product ID codes and the corresponding display will light up. There are 32 ID codes in total. By default, the first code is set and the „-“ indicator lights up.
Open the lid, close it immediately and press the stop button on the remote control before the indicator light goes out. (If you have selected the ID code, the light of the indicator remains lit for 20 seconds).

Jungborn logo