Jungborn Three 52 Wall Mounted Toilet Instruction Manual

: June 12, 2024
: Jungborn

Table of Contents

Three 52 Wall Mounted Toilet
Assembly instructions WC seat
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Assembly Instructions Wall-Mounted Toilet
Jungborn Three 52 Wall Mounted Toilet THREE 52
Art.10520522
Version: 06/23

Three 52 Wall Mounted Toilet

These accessories are not in the installation kit.

Jungborn Three 52 Wall Mounted Toilet - installation

Read the instructions carefully before use and keep them for future reference! For daily cleaning use only commercial bath clea ners. Lime scale and soap residue can be removed with commercial lime remover or vinegar cleaners. Jungborn Three 52 Wall Mounted Toilet -
toilet This is the toilet with some accessories installed.Measure the distance of inlet pipe on the wall and mark it with the letter A (inlet pipe is not included)Measure the distance of inlet pipe on the toilet and mark it with the letter BCut the extra material of the inlet pipe Jungborn Three 52 Wall Mounted Toilet - letter Measure the distance of outlet pipe on the wall and mark it with the letter C (outlet pipe is not included)Measure the distance of outlet pipe on the toilet and mark it with the letter Dut the extra material of the outlet pipeHang the soundproofing pad on the wall(not included) Jungborn
Three 52 Wall Mounted Toilet - Hang Hang the toilet on the wall Jungborn Three 52 Wall Mounted Toilet -
soundproofing Draw the line on the soundproofing pad based on the shape of the toilet Jungborn Three 52 Wall
Mounted Toilet - wall Take the toilet off the wallTake the soundproofing pad off the wallCut the soundproofing pad along the lineHang the soundproofing pad on the wall Jungborn
Three 52 Wall Mounted Toilet - seal Apply the lubricating oil to the seal rings inside the wall for easier installation Put the pipes into the holes on the wallApply the lubricating oil to the outside of the seal ring on the inlet pipe and the inside of the seal ring on the outlet pipe for easier installation![Jungborn Three 52 Wall Mounted Toilet

screw](https://manuals.plus/wp-content/uploads/2023/07/Jungborn-Three-52 -Wall-Mounted-Toilet-screw.jpg)Put 7A into the screw on the wall and rotate it until the notch of the bolts 7A is pointing upwards.Make sure size “a” on the toilet is the same as size “a” on the screwSlide the toilet on the bolts 7A.Rotate the 5A through the seat cover fitting hole with L-shaped screw 6A. Add sealant to the gap between the toilet and the wall

Assembly instructions WC seat

Jungborn Three 52 Wall Mounted Toilet - Fig Adjust the folding pin (7) and bolt (4) to the parallel direction, then plug them into the designated holes on the toilet.Tighten the bolt.Screw the stainless steel screws (4) to the mounting plate (2) so that the mounting platecan still move easily. Jungborn
Three 52 Wall Mounted Toilet - Push Push the WC seat onto the pins of the mounting plate (2) until it snaps into position. Jungborn Three 52 Wall Mounted Toilet - Align Align the WC seat on the toilet.Align the WC vertically towards the top. Next, pull the seat up vertically to remove it. Jungborn Three 52 Wall
Mounted Toilet - mounting Now, screw the mounting plates (2) tight.Now, slide the cover cap (1) onto the mounting plate (2) before pushing the toilet seat back onto the pins so that it snaps into place.
The following steps are for changing wall mounting components Jungborn Three
52 Wall Mounted Toilet - 5A until Put 5A into 4A and rotate 5A until they are tight enough, then put 4A&5A into 3A and rotate them half way(Installed already) Jungborn Three 52 Wall Mounted
Toilet - bottom Place 3A&4A&5A into the hole from the bottom of the toilet (Installed already)Put 2A&8A into the hole from outside (Installed already)Rotate 2A&8A into the hole for around a half distance (Installed already)Connect 2A&8A and 3A&4A&5A with 1A (Installed already)