Conic A001 Stage Light Cutlass User Manual

User Manual
STAGE LIGHT CUTLASS
Conicdesigns.com

Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.

• Unpack and check carefully there is no transportation damage before using the unit.

• Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit.

• It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

• The unit is for indoor use only. Use only in a dry location.

• The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Besure that no ventilation slots are blocked.

• Disconnect main power before replacement or servicing.

• Make sure there are no flammable materials close to the unit while operating as it is fire hazard. ·Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by taking its base.

• Maximum ambient temperature is Ta: 40X. DO NOT operate it where the temperature is higher than this Unit surface temperature may reach up to 85X. DO NOT touch the housing bare-hand during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before replacing or
  serving.

• the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by your self. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.

• DO NOT touch any wire during operation as high voltage might be causing electric shock. Warning:

• To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

• The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged. Caution:

• There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer. Installation:

• The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

• The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people.

Technical Specifications

VOLTAGES:AC 100V-240VX50/60Hz
Light source: 28W LED
Color system:RGBWA Mixed color
Maximum running time (full light): 1 hour /2 hours /3 hours /4 hours /5 hours /6 hours/7hours/8hours /9 hours /10 hours /11 hours /12 hours mode is optional. Maximum running time (solid light): up to 8 hours. Charging time: 7 hours
Stroboscopic: 0-30HZ
Dimming: 4 dimming modes
Control mode: wireless DMX. Mobile APP, remote control
Channel: 4ch/5ch/6ch/7ch/12ch/40ch/80ch/160ch
Display: OLED display screen
Power supply: The charging interface is in the air box, and the adapter can also be used for charging.
Signal connection: 2.4G wireless connection, wireless connection within effective distance Battery:  lithium electronic battery, 9600MAH
Dimensions: 1435MM (length) *50mm (diameter)
Weight: 2.5kg
Heat dissipation system: natural heat dissipation
Shell: aluminum alloy, semi-light oxidized fine black sand. Accessories are standard: infrared remote control and charger. Product features: 1.360 degree light emission, uniform light emission, 2 high color rendering index, long battery life, 3.Bright and saturated colors, 4.Aluminum alloy shell, firm body, compact structure, excellent heat dissipation, equipped with eyebolt and foldable base, and easy installation. 5.The color temperature of 1750K-10000K (unit is 250K) can be adjusted;
6.32 pixels, which can be individually controlled;
7.OLED touch screen, easy to operate;
8. Support wireless DMX (compatible with Swedish wireless), mobile APP, remotecontrol
9. Single lamp control, multi-lamp combination master-slave control, remote control, console control, APP control, etc. Matters needing attention:
1.Built-in battery, away from fire and water sources. If water enters, do not use it again to prevent danger. 2. 2. Please do not disassemble the product for maintenance, please contact tangent who purchased the product.

Control Menu

Color:1-27
Strobe:0-255
Lee Color| DIM:0-255
Lee Color| L101
L102
L105
L106
L107
L110
L111
L115
| | | L116
L118
L119
L121
L124
L126
L127
L128
L132
L135
L139
L147
L151
L152
L158
L164
L174
L179
L180
L201
L203
L204
Strobe:O-255
CCT| DIM:0-255
| CCT| 1750K
2000K
2250K
2500K
2750K
3000K
3250K
3500K
3750K
4000K
4250K
4500K
4750K
5000K
5250K
5500K
5750K
6000K
6250K
6500K
6750K
7000K
| | | 7250K
7500K
7750K
8000K
8250K
8500K
8750K
9000K
9250K
9500K
9750K
10000K
G/M:•1.00-1.00
HSI| DIM:0-255
HUE:0-360
STA:0•100
Auto| Auto Mode:0-60
Speed:1-16
Color.0-27
Sound| Sound Mode:O-3
SENS:0-100
Color.0-27
WIFI| LED_XXX
Master/Slaye| Master
Slave
Wireless DMX| On
Off
Clear
Pairing
Run Time| 1h/2h/3h/4h/5h/6h/7h/8h/9h/10h/11h/12h
Information| Version1.0
Current Time 001135M 005
IR| ON
OFF
Menu Lock| ON
OFF
Back Light| Ahvays On
10s
20s
30s
Factory Reset| ON
YES

DMX Channels

DMX512Control: 4CHA

DMX512Control: 4CHB

DMX512Control: 5CH

DMX512Control: 6CHA

DMX512Control: 6CHB

DMX512Control: 7CH

DMX512Control: 12CH

DMX512Control: 40CH

DIAX512Control: 80CH

DIAX512Control: 160CH

Advanced parameter settings. (In A001 mode press the confirm button for 3 seconds to enter)

on140-100 degree setting range)
Delay| YES| Dimming delay on
NO| Dimming delay off

Infrared remote control function

1. Dimming and speed, up key
2. Dimming and speed, down key
3. OFF Turn off the light
4. ON Turn on the light
5. R, G, B. W. Y keys are five kinds of monochrome
6. The UV key is the color temperature mode, and the up and down keys are used to select
7. 9 numeric keys for 9 static color mixing (AC 1…AC 9)
8. The 0 key is the A001 mode receiving mode, the up and down keys select the address
9. The AUTO key is the color-changing mode, and the up and down keys are used to select the speed
10. The STROBE key is the color selection stroboscopic mode (27 kinds can be selected), and the up and down keys are used to select the speed
11. The FADE key is in gradient mode, and the up and down keys are used to select the speed.
12. The SOUND key is the voice control mode, and the up and down keys are used to select the mode.

WIFI control operation stepsX
Step1: The mobile phone first installs the APP of this software (LED LAMP)
Step2: The lamp display function is switched to WIFI mode. After confirmation, LED-XXX will appear, (XXX represents 3 digits)
Step3: Click the setting icon on the phone, turn on the WIFI and search for the WIFI address, the word LED appears. Such as “LED-XXX”, click the link, and exit this interface after the connection is successful.
Step4: Click the LED LAMP icon on the mobile phone, it shows that the connection is successful and you can control it. (This lighting APP control software can only use LED LIGHT control softwareX Features:

1. Support master-slave connection advanced parameter setting
2. Support standard DMX512 and wired RDM
3. Support software online upgrade
4. Support temperature control settings
5. Support wireless 2.4G connection
6. Support mobile APP control (Android and Apple)

http://url.szszjkj.com/79810915950

Trouble Shooting

Following are a few common problems that may occur during operation. Here are somesuggestionsforeasy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the unit or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit.

C. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition

Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.
Clean with soft cloth using normal glass cleaning fluid. Always dry the parts carefully. Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60days.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>