Polaris H0748700 Cordless Robotic Cleaner User Guide

Polaris H0748700 Cordless Robotic Cleaner

Product Information

• Battery Status:
  • Solid Green: Fully charged.
  • Blinking Green: Ready to run a full cycle (2h 30).
  • Solid Orange: Not fully charged. May not run a complete cycle.
  • Blinking Orange: Very low battery level. Charge needed. Cannot run cleaner.
  • Blinking Red: Charging error. Cleaner is too hot.
• Wi-Fi Connection Status:
  • Blinking Blue: Pairing.
  • Solid Blue : Connected to WiFi.
• Cleaning Mode:
  • Floor and walls (2h 30)
  • Floor only (1h 30)
• Operating Status:
  • Blinking Blue: Out of Water: Ready to submerge, start cleaning. In Water: End of Cycle. Waiting for removal from pool.
  • Blinking Red: Error.
• Charging Station Status:
  • Solid Green : Base receiving power.
  • Solid Red: Charging in progress.

Product Usage Instructions

1. Select a charging location (GFCI outlet) at least 11.5 ft (3.5 m) away from the pool, out of direct sunlight, and with adequate WiFi strength. Align the cleaner and charging station with the wall for easier access to the controls and handle. DO NOT use an extension cord.
2. Plug the charging station into the GFCI outlet and seat the cleaner on the charging contacts. The cleaner will beep and begin charging.
3. Check the current charge level in the app whenever the cleaner is on the charging station.
4. Ensure that the cleaner is fully charged before the first cleaning.
5. To start cleaning, press the “Start Cleaning” button or select the desired cleaning mode on the cleaner.

Before You Start
This Quick Start Guide contains essential installation and startup instructions. Read the complete manual and all safety warnings before commencing installation.

What’s In the Box

Information/Status LEDs

Battery Status

• Solid Green
  Fully charged.

• Blinking Green
  Ready to run a full cycle (2h 30).

• Solid Orange
  Not fully charged. May not run a complete cycle.

• Blinking Orange
  Very low battery level. Charge needed. Cannot run cleaner.

• Blinking Red
  Charging error. Cleaner is too hot.

Wi‑Fi Connection Status

Charging Station Status

• Solid Green : Base receiving power
• Solid Red : Charging in progress

Setup and Charging

• Select a charging location (GFCI outlet) at least 11.5 ft (3.5 m) away from the pool, out of direct sunlight and with adequate Wi‑Fi strength. Align the cleaner and charging station with the wall for easier access to the controls and handle. DO NOT use extension cord.
• Plug charging station into GFCI and seat cleaner on the charging contacts. Cleaner “beeps” and begins charging.

Start Cleaning

Check current charge level in the App whenever the cleaner is on the charging station.

• Fully charge the cleaner before the first cleaning.

GREEN Blinking = Ready to run a full cycle (<5h) | GREEN Solid = Fully Charged

• Select Cleaning Mode using the slider or the App.

• Choose Floor Only mode to clean with Pool Cover on.

• Additional cleaning modes may be available in the App.

• Start the cleaner. Use the slider or the App.
  

• Submerge the Cleaner.

Blinking Blue = Ready to Clean. Cleaner does not begin moving until it senses water. If water is not detected after 15 seconds, slide and release the slider and press Start again.

• Wait for bubbles to stop completely, then let the cleaner sink to the bottom of the pool.
• Cleaning cycle will start as soon as the cleaner detects the pool floor.

Remove from Pool

Remove from Pool – Waterline Waiting

• During the last 10 minutes of a cycle, (other than Floor Only), the cleaner climbs and waits at the waterline.
• If the cleaner is not retrieved after 30 seconds, it moves to a different wall. If not retrieved after 10 minutes, the cleaner returns to the pool floor for retrieval with the hook and pole.

Remove from Pool – Using the Hook

• Attach the hook (stored on the charging base) to a standard pool cleaning pole (not included).

• Secure the hook on the cleaner handle. Bring the cleaner to the waterline.

• Hold the cleaner by the handle. Let the water drain.

• Remove the filter canister and rinse.

• Store the cleaner on the charging station out of direct sunlight.

For best results, dry the cleaner and station charging contact before charging.
Periodically clean the charging contact using a cloth or scouring pad and fresh water.

After 8 days of inactivity, the cleaner will enter Deep Sleep mode with all LEDs off. Re-set the cleaner on charging base to wake up.

Install the App and Add your Cleaner

WiFi signals cannot travel underwater. Most app functions are therefore not available during a cleaning cycle. Place the cleaner back on the charging stand to reconnect to WiFi.
Before you begin installing iAquaLink®, make sure you have the following:

• Charging station connected and plugged into a GFCI outlet.
• Robotic Cleaner on Charging station.
• Wi‑Fi and Bluetooth enabled smart device (phone or tablet).
• Wi‑Fi router with sufficient signal strength at the Charging station.
• IMPORTANT: Have your Wi‑Fi network password available.

1. Download iAquaLink app from the App Store or Google Play.
2. Open the iAquaLink app, then Sign Up or Log In.
3. Follow the on‑screen prompts to add your cleaner.
4. Slide the slider right and HOLD for ten seconds to put the cleaner in Pairing Mode. Wi‑Fi LED indicates connection status.

If you have problems connecting, the Wi-Fi signal may not be strong enough next to the pool. Try placing the charging station cleaner in another location closer to your home router.

Zodiac Pool Systems LLC
2882 Whiptail Loop # 100
Carlsbad, CA 92010, USA
PolarisPool.com | 1.800.822.7933
Zodiac Pool Systems Canada, Inc.
2-3365 Mainway
Burlington, ON L7M 1A6, Canada
PolarisPool.ca | 1.800.822.7933
A Fluidra Brand
©2023 Zodiac Pool Systems LLC. All rights reserved. ZODIAC® is a registered trademark of Zodiac International,
S.A.S.U., used under license. All other trademarks are the property of their respective owners.
H0748700_REVC

References

• Home | Polaris Pool
• Home | Polaris Pool

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>