RAZER BE200NGW Wireless LAN Adapter Card Installation Guide

RAZER BE200NGW Wireless LAN Adapter Card

Specifications

• Model: BE200NGW
• Wireless Standards: 802.11a/b/g/n/ac/ax/be
• Wireless LAN Type: mini-PCIe card
• FCC ID: RWO-RZ090510 (global market), PD9BE200NG (U.S. market)

Jan. 2, 2024

Federal Communications Commission

7435 Oakland Mills Road
Columbia, Maryland 21046

USA
Subject: Model BE200NGW Wireless LAN Adapter Card
FCC ID: RWO-RZ090510

Gentlemen

Please be advised that the Model BE200NGW 802.11a/b/g/n/ac/ax/be + BT Wireless LAN mini-PCIe card is manufactured for the global market but when marketed in the U.S. under FCC ID: PD9BE200NG.
This device meets the requirements of FCC Part 15.202 and accordingly will be programmed at the factory to active scan on the following non-DFS channels to initiate communication during normal WLAN operation. When operating in Wi-Fi Direct mode on these non-DFS channels, it may operate as a P2P client device or GO to establish a P2P network if, and only if, a master device is present and network communication is maintained between a master device and the GO.

• Channels 36-48, 5180-5240MHz 802.11a mode
• Channels 36-48, 5180-5240MHz 802.11n/ac/ax/be mode (20 MHz channel)
• Channels 38-46, 5190-5230MHz 802.11n/ac/ax/be mode (40MHz channel)
• Channels 42, 5210MHz 802.11ac/ax/be mode (80MHz channel)
• Channels 50, 5250MHz 802.11ac/ax/be mode (160MHz channel)
• Channels 149-165, 5745-5825MHz 802.11a mode
• Channels 149-165, 5745-5825MHz 802.11n/ac/ax/be mode (20 MHz channel)
• Channels151-159, 5755-5795MHz 802.11n/ac/ax/be mode (40MHz channel)
• Channel 155, 5775MHz 802.11ac/ax/be mode (80MHz channel)

This device meets the requirements of FCC Part 15.202 and 15.407 as a 5.9GHz band Indoor client module (UNII) and accordingly will be programmed at the factory to passive scan on the following channels. On these channels, a) the client device will not directly connect to another client device, b) will only associate and connect with an indoor Access Point (AP) or indoor subordinate, and c) the Client device (EUT) will always be under the control of an indoor AP. However. there may exist situations where the client may transmit brief messages, prior to being under the control of an AP, to join an AP network. But these brief messages will only occur if the client has detected a signal confirming that an AP is operating on a particular channel. These brief messages will have a time-out mechanism if it does not receive a response from an AP.

• Channels 169-177, 5845-5885MHz 802.11a mode
• Channels 169-177, 5845-5885MHz 802.11n/ac/ax/be mode (20 MHz channel)
• Channels 167-175, 5835-5875MHz 802.11n/ac/ax/be mode (40MHz channel)
• Channel 171, 5855MHz 802.11ac/ax/be mode (80MHz channel)
• Channel 163, 5815MHz 802.11ac/ax/be mode (160MHz channel)
• Channel 1-233, 5955-7115MHz 802.11ax/be mode (20MHz channel)
• Channel 3-277, 5965-7085MHz 802.11ax/be mode (40MHz channel)
• Channel 7-215, 5985-7025MHz 802.11ax/be mode (80MHz channel)
• Channel 15-207, 6025-6985MHz 802.11ax/be mode (160MHz channel)
• Channel 31-191, 6105-6905MHz 802.11be mode (320MHz channel)

This information when programmed into the NVM will not be accessible and cannot be changed by the end user. The transmitter is approved as a non- software-defined radio and OEMs and third-party system integrators do not have the ability through software to allow configuration controls that would permit the device to operate outside the grant conditions per FCC KDB 594280.

Sincerely,
Johnsen Tia Director, Regulatory & Compliance Razer Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>