Pro sKit MT-7612F Multi Function Optical Time Domain Reflectometer User Manual
- June 13, 2024
- Pro sKit
Table of Contents
Multi-function Optical
Time Domain Reflectometer
MT-76I12F
User’s Manual
MT-7612F Multi Function Optical Time Domain Reflectometer
WARNING
Any undefined change or modification of this manual will deprive you of the
right to operate the equipment. To reduce the risk of fire or electric shock,
do not expose the equipment to rain or humidity. To prevent electric shock,
please do not open the shell, and it must be repaired by qualified personnel.
This device supports on-line test with signal, should satisfy following norms:
1270nm / 1310nm / 1490nm Power <+10dBm
1577nm Power <0dBm : 1550nm Power < -20dBm
If out of range, it may lead to device broken, which is out of warranty range
NOTE
As the laser is harmful to the eyes, don’t look directly at the laser
outlet and don’t attempt to disassemble the cabinet.
PRECAUTIONS FOR USE
Using the battery
The device can be recharged with a special battery, and can not be mixed with
different types or capacity batteries.
Avoiding condensation:
Sudden changes in temperature should be avoided. Do not use the device
immediately after moving the device from the cold area to the hot area, or
when the room suddenly heats up, because the device may have condensation
phenomenon.
If the temperature changes abruptly , stop using it and take out the battery,
and the power can be switched on after atleast an hour.
Storage:
When the device is not used for a long time, please take out the battery to
avoid the damage caused by battery leakage.
The content of this manual is for reference only, and everything is based on
the actual product.
Host
Buttons
- Setting: In OTDR interface, press to set up.
- Zoom control: Operate with direction and ESC key for waveform.
- Power: Long press to turn on, or choose to turn off.
- Direction: Select up, down, left, and right.
- Marker: Switch cursorin OTDR interface.
- Save/File: In OTDR interface, press to save or enter the file.
- Scan: In OTDR interface, press to measure.
- Esc: Return to the previous menu.
- Enter: Enter the next level page or confirm the operation.
Main Menu
After booting, device will enter main menu and selects Mini OTDR function
automatically. Select function module with direction buttons, press “ ” button
to enter the corresponding function.
Title Bar
Highlight when
the function module is selected
OTDR
Select Mini OTDR module in the main menu, and press “ “to enter the OTDR
interface
OTDR-Measure settings
The judgement of events list is based on measure setting. Wrong setting might
leads to wrong or missing events In OTDR interface, press “ ” button to enter
measure setting Wavelength-—-Wavelength of laser.
Scan mode—Manual and auto mode. Under auto mode, device will match the
distance range and pulse width.
Scan type- Real time: Real-time measurement can quickly judge basic faults of
optical fiber; Average: judge the line condition more accurate, get a better
SNR measure curve.
Range—Match with the length of measured optical fiber, usually over one level.
Pulse width—Set the pulse width of output laser.
Average time—Set average time: The longer average time, the better measure
curve.
Splice loss-—-Treatas an event when the loss is higher than setting value.
Reflection threshold-—-Treat as an event when reflection is higher than
setting value.
End threshold—Treat as the end of optic fiber when loss is higher than setting
value
Optical detector—
Before measurement, set to check whether light input s in the fiber or not.
Real time analyse—
Set to turn on or turn off the event analysis after real-time measurement.
OTDR-Measure
Press the” ” button in OTDR interface to run measurement Real-time:
During measuring, you can change range, zoom in or zoom out with direction
buttons and zoom control button. Press” ” again to stop.
If real-time analyse function is on, the device will analyse events after
measurement Average:
Average measurement can judge the line condition more accurate. It can get a
better SNR and fits high requirement circuit. User can set measurement time
from 5 to 180 seconds. The device analyses events and generates event list
automaticity.
press” ” ssintostop measurement 2020-01-01 WED 10:08
OTDR-Event & Wave Control
Event list shows 5 events at one time, press Up or Down button to check the whole event list. Press” ” to select marker. Use the following combination buttons to zoom in and out.
OTDR-File Save
After finishing measurement, press the “ ” button to save the file and the keyboard will pop up. If the Auto Name function is turned on, the file name is automatically generated when saving.
OTDR-Files
When there is no measurement, press the “ “button to enter the file list. Press the “ ” button to open the folder or file, and press the button to pop up the operation item. The waveform thumbnail is displayed at the bottom.
OPM/VFL
Select OPM/VFL module in the main menu, and press “ ” to enter the OPM/VFL
interface.
Press the “ “button to enter the OPM setting interface.
System
Select System module in the main menu, and press “ “to enter the System interface The device supports USB communication function:
OTG: Short for On-The-Go, open to view TF card files.
USB connection: Connect to view internal storage file.
Auto
Power Off: Set time of automatic off or cancel
Auto name: Name automatically when file saving.
Brightness: Set brightness from 10 to 100.
Voice: Turn On /Off of voice feedback.
Data: Set current date.
Time: Set current time.
Format storage device: TF card connected –Format TF card.
No TF card –Format internal storage.
Factory settings: Restting to default, Date, time ,storage files are not
affected
Detail parameters
| Basic
---|---
Display| 3.2 Inch color LCD 320480
Data sotrage| Internal storage 500 records.Maximum 32GTF Card
Beep| Passive electromagnetic buzzer
Backlignt| 10 levels of brightness
Power saving| Adjustable auto power off
Power supply| 3.7V/2.4Ah Lithium Battary,standby>7.5H ,measurement>4H
Temperature| Working 0-50°C,storage:-20-70°C,<90% RH
Size and weight| 168mm82mm40mm,c≈260g
OTDR
Wavelength| 1550nm±20nm
Dynamic range| 20dB
Distance range| 0.1∼80km
Pulse width| 5ns∼20µs
Measurement time| 5-180s Adjustable
Attenuation blind area| 8m
Event blind area| 3m
Loss threshold| 0.01dB
Loss resolution| 0.001 dB
Distance uncertainty| -±(0.8+0.005%distance+Sambling resolution)m
Input light detection| Yes
VFL
Wavelength| 650nm±20nm
Output power| 1 mW
Blink| 2Hz
OPM
Detect range| -50∼+26dBm
Detect wavelength| 700∼1700nm
Measured wavelength| 850,980,1270,1300,1310,1490,1550,
1577,1625,1650nm
Accuracy| ±0.2dB
Resolution| 0.01dB
REF Function| Yes
http://www.prokits.com.tw
PROKIT’S INDUSTRIES CO.,LTD
https://www.prokits.com.tw
Email: [email protected]
©2023 Prokit’s Industries Co., LTD. All rights reserved 2023001(C)