Pro sKit FB-1601 Fiber Cleaver User Manual

June 3, 2024
Pro sKit

Pro sKit FB-1601 Fiber Cleaver

Pro-sKit-FB-1601-Fiber-Cleaver-
product

INSTRUCTION

Thanks for purchasing Pro’s Kit FB-1601/1602 Fiber Cleaver. The fixture of product configuration is three in one fixture for single fiber Ø 250μm & Ø 900μm or 3x2mm drop cable. Please read the instructions carefully before using the product. This product has been designed and manufactured to assure personal safety. Improper use can result in body injury and serious damage to fiber cleaver. Please read and observe all warning instructions given in this operation manual.

  1. Do not disassemble or lubricate any parts of cleaver. Doing so could cause serious damage to the cleaver.
  2. The FB-1601/1602 is a precision tool. Do not impact the cleaver by hitting or dropping it. Doing so may cause personal injury and loss of cleaving performance.
  3. Glass fiber fragments are extremely sharp. Handel with care. Wear safety glasses at all time during cleaving operation for protection from glass fiber.
  4. Dispose of glass fiber fragments properly.
  5. The blade of cleaver is extremely sharp. Do not touch it with bare hands.
  6. Do not impact the Clamp Cover. Doing so could cause damage to cleaver and loss of cleaver performance.
  7. If cleaver is damage or problem occurs, please contact our maintenance service center.

SPECIFICATION

Cladding Diameter 125 μm
Fiber Count Coating Diameter Single fiber Ø 250μm & Ø 900μm /3x2mm Drop cable
Cleaver Length 5-20mm
Dimensions 80(L)x 64 (W)x60(H) mm
Weight (FB-1601/FB-1602) ~250g/280g
Cleaver Blade (5FB-1602-BLADE) 24 Points

VFL (#FB-1602 only):

Wavelength 650nm±20nm
VFL Connector 2.5mm Universal Connector
Output Power 1mW
Operation Mode CW/2Hz Glint
Power Source 3.7V/180mAh Li-ion
Charge 5V/0.2A
Accessories Micro USB charging cable

STRUCTURE

Pro-sKit-FB-1601-Fiber-Cleaver-fig-1

Indicator will light up green while charging; it will turn off when charging completes.

OPERATION PROCEDURE

  1. Open the clamp cover and fiber holder lid. Please make sure the blade carriage should slide forward automatically.Pro-sKit-FB-1601-Fiber-Cleaver-fig-2
  2. Insert the fiber cable into the correct groove with the end of the fiber coating.
  3. Close the fiber holder lid and clamp cover.
  4. Slide the blade carriage to rear side of the cleaver. The fiber will be cleaved.
  5. Open the clamp cover; then open the fiber holder lid and lift the newly cleaver fiber. Lift the off-cut and dispose it properly.

CLEAN

  1. After cutting, please clean the broken fiber. Clean the dirt on the fiberboard with cotton stick that dipped in alcohol. Do not use acetone or corrosive solvent to clean the fiberboard. Do not damage the blade for future use.
  2. Clean the dirt on the fiberboard regularly with cotton stick that dipped in alcohol. Do not use acetone or corrosive solvent to clean the fiberboard

CAUTION

  • Do not rotate the blade with hands.
  • Do not rotate the blade with metallic tweezers. Doing so may damage the blade.
BLADE REPLACEMENT AND ADJUSTMENT

Adjust the blade (rotate according to 0.1… 23 points indicated on the blade)
First of all, the screw driver will loosen the screw on the blade, use the cotton swab to rotate the blade to adjust the position of the blade, rotate one face at a time, and the rotation mode is indicated by the arrowPro-sKit-
FB-1601-Fiber-Cleaver-fig-3

Adjust blade height

  1. Loosen the two phillips screws shown in the figurePro-sKit-FB-1601-Fiber-Cleaver-fig-4
  2. Adjust the screw as shown and adjust the blade height
  3. Lock the loosened screws

Blade replacement

  1. Unscrew the blade setscrew. (circle mark)
  2. Remove the blade with tweezers.Pro-sKit-FB-1601-Fiber-Cleaver-fig-5

TROUBLESHOOTING

If there is a problem with the cutter, it may be due to the following reasons

Problems Exclusion method
The optical fiber is placed askew Make sure that the optical fiber is

straight into the cutter slot holder
Blade position too high| Adjust blade height
Dirty optical fiber pressure pad| Clean optical fiber pressure pad Remove and clean the fiber
Dirty cutting blade| Clean the cutting blade
Dirty optical fiber| Remove and clean the fiber

VFL (FB-1602 only) has problems, which may be caused by the following reasons

Questions Exclusion method
VFL does not work or Glint mode is not available The battery is dead or l[ow

battery](https://www.baidu.com/link?url=K030Dq-dH-I775aW3bLOQWfeA- sffOVOD5S_8AHZMXzSLdT4LrAi4CEBYc6UcNu1BeRDd1aDh2m3AMSO0qx509YRz3x9mGGnEu2wNm1NNHK&wd&eqid=b20941f800043a9e000000045f814089). Charge it in time
Port coupling porcelain tube damaged| Replace the porcelain tube

PROKIT’S INDUSTRIES CO., LTD
https://www.prokits.com.tw
Email: pk@mail.prokits.com.tw
©2021 Prokit’s Industries Co., LTD. All rights reserved 2021001(C)

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals