Pro sKit MT-8100 Phone Tester User Manual

October 30, 2023
Pro sKit

Pro sKit MT-8100 Phone Tester

Pro’sKit Phone Tester Model

The Pro’sKit MT-8100 phone tester is a tool used by installers and repair technicians to test copper wire voice subscriber lines. It is easy to use and comes with a range of features that make it useful for testing and troubleshooting telecom lines.

Specifications

  • Loop span limit: 2k maximum at 48V DC (nominal 20mA minimum loop current)
  • DC resistance
  • Talk mode monitor impedance: 300 typical, 39k nominal at 1 KHz
  • Rotary dial output
  • Pulsing rate
  • Percent break interdigit interval
  • Leakage during break
  • DTMF output tone frequency error
  • Tone level high versus low tone difference
  • Memory dialing memory capacity digit capacity
  • PBX pause duration
  • Line voltage test monitor amplifier
  • Power source automatic power shut off
  • Speaker phone levels power source
  • Physical characteristics measurement weight water resistance cord sets environmental conditions temperature relative humidity certificate
  • 13 memories including M1, last number redialing 16 digits per memory
  • 4 seconds 5 phase AC/DC voltage indication
  • 9V transistor provides 25 hours continuous use, typical after 5min. of no audio signal
  • Electronic adjustable battery (9V) 6F22 (not included)

Product Usage Instructions

  1. Before using the Pro’sKit MT-8100 phone tester, ensure that it is powered by a fully charged 9V transistor battery.
  2. To test a copper wire voice subscriber line, insert the angled bed of nails into the cable or use the auxiliary RJ-11 modular plug to connect directly to the telecom jack.
  3. The phone tester features line voltage test, continuity test, and two-way hands-free amplified speakerphone for convenient testing and troubleshooting.
  4. You can store up to twelve 16-digit numbers in repeat dialer (speed dialing), plus extra number store in M1 button. The last number redial feature is also available.
  5. The PBX pause button and mute switch allow for more advanced testing and troubleshooting.
  6. The electronic switch for speakerphone/monitor volume control and automatic shut-off after five minutes of inactivity make the phone tester easy to use.
  7. The Pro’sKit MT-8100 phone tester is dust- and waterproof with drop protection and comes with a relocatable steel locking belt clip for added convenience.

Description

Pro’sKit MT-8100 phone tester is used by installers and repair technicians to test copper wire voice subscriber lines. Pro’sKit MT-8100 phone tester is easy to use, features line voltage test, continuity test, two-way hands-free amplified speakerphone, speed dialing, low battery indicator and a rugged locking belt clip.

Features

  • Dust- and waterproof, drop protection.
  • Outer-lead voltage, battery low voltage and continuous polarity LED indicators.
  • On/off checking feature for telecom line connections.
  • Speakerphone for convenient hands-free two-way conversation.
  • Tone and pulse operation.
  • Store up to twelve 16-digit numbers in repeat dialer (speed dialing), plus extra number store in M1 button.
  • Last number redial feature.
  • PBX pause button and mute switch.
  • Electronic switch for speakerphone/monitor volume control.
  • Automatic shut-off after five minutes of inactivity.
  • Relocatable steel locking belt clip.
  • Audible electronic ringer.
  • Angled bed of nails for stabbing into the cable, and the auxiliary RJ-11 modular plug for direct insertion into telecom jack.

Specifications

Loop Span Limit| 2 kΩ maximum at 48 V DC

(nominal 20 mA minimum loop current)

---|---
DC Resistance
Talk Mode| 300 Ω typical
Monitor Impedance| 39 kΩ nominal at 1 KHz
Rotary Dial Output
Pulsing Rate| 10 pps + 0.8 pps
---|---
Percent Break| 61%±2%
Interdigit Interval| 1000 ms typical
Leakage During Break| >50 KΩ
DTMF Output
Tone Frequency Error| ±1.2% maximum
Tone Level| -8±2 dBm combined (typical)
High Versus Low Tone Difference| 4 dB maximum
Memory Dialing
Memory Capacity| 13 memories including M1, last number redialing
Digit Capacity| 16 digits per memory
PBX Pause Duration| 4 seconds
Line Voltage Test| 5 phase AC/DC voltage indication
Monitor Amplifier Power Source| 9 V transistor; provides 25 hours continuous use, typical
Automatic Power Shut Off| after 5 min. of no audio signal
Speaker Phone Levels| electronic adjustable
Power Source| battery (9V) 6F22 (not included)
Physical Characteristics
Measurement| 230 × 82 × 89 mm

(9-1/16” × 3-15/64” × 3-1/2”)

Weight| 635 g typical
Water Resistance| dust protection & waterproof tested to an IEC/EN

60529 IP54 rating

Cord Sets| angled bed of nails and RJ11 plug
Environmental Conditions
Temperature| Operating: 0 to 50°C
| Storage: <-10 to 60°C
Relative Humidity| 5 to 95%
Certificate| IP54, CE approved

Package Include

  • 1x Butt set tester
  • 1x Line cord with angled bed of nails and RG-11 plug 2x Replacement fuse
  • 1x User’s manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals