TECNO CAMON 20 Premier 5G Smartphone User Manual
- June 13, 2024
- TECNO
Table of Contents
TECNO CAMON 20 Premier 5G Smartphone
Explosion diagram specification
| 1 | OLED | 2 | FC HEAT FILM |
|---|---|---|---|
| 3 | VC | 4 | MID COVER ASM RNM |
| 5 | ESD GD | 6 | CAMERA BRACKET |
| 7 | F CAM | 8 | UP SPK |
| 9 | MAIN PCBA | 10 | CABLE 1 |
| 11 | PS RUBBER | 12 | CABLE 2 |
| 13 | CAM CON FOAM | 14 | BAT FPC BTB RUBBER KC3 |
| 15 | 50M CON FOAM | 16 | LCD BTB RUBBER CK9N |
| 17 | PCBA P MYLAR | 18 | 108 CAM CON FOAM |
| 19 | 50 CAM CON FOAM | 20 | 108M CAM |
| 21 | 50M CAM | 22 | ELE LCD FPC FOAM B |
| 23 | LASER CON FOAM | 24 | 2M CAM |
| 25 | RCAM RUBBER 2M | 26 | SHIELDING HOT FLIM |
| 27 | LASER FPC | 28 | LASER SENSOR RUBBER |
| 29 | MCAM LENS DECO | 30 | REAR 50M CAM GLASS |
| 31 | REAR 108M CAM GLASS | 32 | FLASH FPC |
| 33 | FLASH CON FOAM | 34 | LOWHOUSING ASM |
| 35 | NFC | 36 | BATTERY COVER |
| 37 | LASER LAMPSHADES | 38 | FLASH LAMPSHADES |
| 39 | REAR 2M CAM GLASS | 40 | MIAN FPC |
| 41 | MOTOR | 42 | SIM PCBA |
| 43 | BATTERY | 44 | FINGERPRINT |
| 45 | REAR FINGERPRINT FOAM | 46 | USB PCBA |
| --- | --- | --- | --- |
| 47 | SIM TRAY | 48 | SCREWS |
| 49 | USB RUBBER | 50 | ANT PCB |
| 51 | VC MYLAR ASM | 52 | SPK BOX |
| 53 | RF CABLE CON CLOTH | 54 | SIDEKEY FPC |
| 55 | SIDEKEY VOICE FRAME | 56 | SIDEKEY POWER FRAME |
| 57 | POWER VOICE | 58 | SIDEKEY VOICE |
| 59 | SPK HOT FILM | 60 | REAR GRAPHITE |
Know your phone
- Front Camera
- Volume + key
- Volume – key
- Power key
- NFC
SIM/SD card installation
- Power off mobile.
- Refer to the following picture for SIM / SD card installation.
Charging the phone
You can charge your device using a charger or by connecting it to the computer
using a USB cable (which comes with the phone). Use only the TECNO charger and
cables. Other chargers or cables may damage the device. This will invalidate
your phone warranty.
FCC Caution
Labeling requirements
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Information to the user
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Information to the user
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information
This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of the USA (FCC) is 1.6 W/kg averaging over one gram of tissue. Device types: CK9n (FCC ID: 2ADYY- CK9N) have also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.123W/kg and when properly worn on the body is 0.540W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10 mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters, and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 1.0 cm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or approved antenna.
HiOS runs on AndroidTM OS. Android is a trademark of Google LLC.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>