havit HV1507T-SS316 Tivah 316 Stainless Steel TRI Colour Double Adjustable Instruction Manual

havit HV1507T-SS316 Tivah 316 Stainless Steel TRI Colour Double

Adjustable

Tivah Bollard Light Installation Instructions

Product Specifications| Dimensions
Model No.| HV1507T-SS316-240V| HV1507T-BLK-240V| HV1507T-SS316-12V| HV1507T- BLK-12V| Mounting Base Dimensions

Name| Tivah| Tivah
Material| 316 Stainless Steel| Aluminium| 316 Stainless Steel| Aluminium
Colour| Stainless Steel| Black| Stainless Steel| Black
IP Rating| IP65| IP65
Input Voltage| 240V| 12v DC
Protection Class| (240v Requires Earth)| (Low Voltage)
Lamp Base| GU10| MR16
Lamp Wattage| 2x 5w| 2x 5w
Colour Temp| TRI Colour – 3000k, 4000k, 5500k| TRI Colour – 3000k, 4000k, 5500k
Lumens| 2x 270lm, 2x 285lm, 2x 300lm| 2x 270lm, 2x 285lm, 2x 300lm
CRI| > 80| > 80
Wiring| Parallel| Parallel
Dimmable| No| No
Warranty| 3 Years Replacement| 3 Years Replacement

Important Safety Issues

• This product must be installed by a qualified electrician according to AS/NZS 3000.
• Ensure all electrical mains are disconnected before any installation.
• Modification of this product will void any warranty.
• Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
• All electrical connections must be watertight, If a watertight connection is not done, Warranty will be voided.
• Electrical cannot be submersed under water, If connection is under water, Warranty will be voided.
• When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
• All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining).
• When installing surface mounted bollards, base plate must be installed on concrete or concrete pad, Fitting should not be installed under ground level, all holes including cable entry must be silicone to prevent any water pentation into fitting, silicon must also be applied around fitting at ground level. Failure to do this will void warranty
• All o-rings and seals must be in place correctly to maintain warranty.
• These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.

Steps for Installation: HV1507T-240V

1. Make sure that the electrical circuit is free of voltage (master switch off ).
2. Locate IP rated junction box within fitting. Undo screws from junction box and remove cover.
3.  Insert cable through cable gland on junction box. If your cable is not circular you must fix entry of your cable to maintain IP rating. Failure to do so will void warranty.
4.  Connect the cable using wire with earth. Connect earth first, then live and neutral wires.
5. Reattach cover to IP rated junction box making sure screws are tight and seals are still in place.
6. Install bollard in desired location using appropriate screws for application. The screws supplied are mild steel which must be replaced with higher grade if there is any chance of them being affected by water.
7. Silicon all cable entry holes and fixing points on baseplate to avoid moisture penetration into fitting.
8. Colour temperature is set to 3000K. To change, remove caps from fitting by twisting anti clockwise. Remove globe and select desired colour temperature by moving switch on side of globe and reinsert globe.
9. Attach covers by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
10. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Installation: HV1507T-12V

1. Make sure that the electrical circuit is free of voltage (master switch off ).
2. Locate IP rated junction box within fitting. Undo screws from junction box and remove cover.
3. Insert cable through cable gland on junction box. If your cable is not circular you must fix entry of your cable to maintain IP rating. Failure to do so will void warranty.
4. Using an appropriate 12V DC LED driver – DO NOT CONNECT FITTING DIRECTLY TO 240V
5. Connect live and neutral wires. If more than one fitting is installed, wiring must be done in parallel.
6. Reattach cover to IP rated junction box making sure screws are tight and seals are still in place.
7. Install bollard in desired location using appropriate screws for application. The screws supplied are mild steel which must be replaced with higher grade if there is any chance of them being affected by water. The location of baseplate must be installed on either concrete or concrete base and cannot be installed under ground level.
8. Silicon all cable entry holes and fixing points on baseplate to avoid moisture penetration into fitting.
9. Colour temperature is set to 3000K. To change, remove caps from fitting by twisting anti clockwise. Remove globe and select desired colour temperature by moving switch on side and then reinsert globe.
10. Attach covers by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
11. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Must be installed by a licensed electrician

Contact Details:|  | **Warranty Terms & Conditions*|  | Additional Information
---|---|---|---|---
143 Beauchamp Road                       Tel: 02 9381 8300
Matraville NSW 2036                           Fax: 02 9666 8881
Australia                                          Email: sales@havit.com.au Web: www.havit.com.au|  | **| |

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>