GLEMM PAA 2240 240W PA Amplifier Instruction Manual

: June 13, 2024
: GLEMM

**GLEMM PAA 2240 240W PA Amplifier Instruction Manual

**

INSIDE THE PACKAGING

Amplifier
Remote control
Power cable
Manual

TECHNICAL SPECIFICATIONS

Item	PAA 2240	PAA 2480
Max Power	2 x 240W	2 x 480W
RMS power	2 x100W	2 x 200W
Constant voltage	100V
Supported impedance	8 -16 Ohm
Inputs	MIC 1-3: 5-8mV, 600 Ohm, LINE: 150-470mV, 10KOhm, RCA unbalanced
S/N ratio	Line >85dB, Mic > 72dB
Line Out	0,775(0dBV)
Frequency response	60 Hz -15 Khz (+/-3dB)
THD	Less than 0,5%
Power consumption	300W	I 600W
Protections	Short circuit, overload, overheating
Power supply	220-230V — ; 50-60Hz
Remote battery	Lithium 3V CR 2025 (not included)
BT frequency	2,4 Ghz
Dimensions	484 x 405 x 88 mm
Weight	6,6 KgI	9,6 Kg

The manufacturer, in order to improve its products, reserves the right to modify their characteristics whether technical or aesthetic, at any time and without notice.

THANK YOU FOR YOUR PURCHASE

The product you have purchased is the result of careful planning by specialized engineers. High quality materials were used for its construction, to ensure its functioning over time.
The product is manufactured in compliance with the strict regulations imposed by the European Union, a guarantee of reliability and safety.
Please read this manual carefully before starting using the device in order to take advantage of its full potential. Hoping that you will be satisfied of your purchase, we thank you again for your trust in our brand and we invite you to visit our website www.glemm.eu where you will find the whole range of our products, along with useful information and updates.

CAUTIONS AND WARNINGS

Read and follow strictly the instructions contained in this manual.
Keep this manual for future reference and include it if you give the product to another user.
When you open the package check that product is intact and that all the accessories are included.
This device works with dangerous 230V mains power. Do not open, do not disassemble and don’t try to operate inside it. In case of wrong use an electric shock may occur.
The product is conceived for professional use. Its installation must be carried out exclusively by specialized technicians, skilled in electric and audio systems.In case of wrong installation or connections, the manufacturer doesn’t take any responsibility for damages to people or objects.
Make sure that your power outlet voltage matches with the voltage set on the product. A wrong voltage would seriously damage the fixture.
To avoid the risk of dangerous electric shocks, before turning on the product always check that it is connected to ground. Never cut internal or external ground wires. Never remove ground wiring from the protective ground terminal.
Before making any connection with other devices, check that all the fixtures are disconnected from the power source and that all the volumes are set on minumum.
The product is not suitable for outdoor use. To avoid the risk of shortcircuits don’t expose it to high temperatures (above 40°), rain or humidity.
Do not allow flammable liquid, water or metal objects to enter the product.
Don’t touch the product with wet hands.
Do not place any recipients filled with liquids, such as vases, on top of or directly next to the appliance.
Install the product in a stable and ventilated position, far from heat sources and don’t obstruct the air vents.
Use the fixture and its controls with due accuracy, avoiding falls, vibrations or impacts.
If the product doesn’t turn on, check the fuse and if necessary replace it with one of the same type and rating, after disconnecting the fixture from power.
In the event of a serious operating problem, stop using the product immediately. Never try to repair it by yourself, but contact the authorized technical service
center. Repairs carried out by unskilled persons could lead to serious damages both to the fixture and to people.
Do not turn the product on and off at short intervals, it may reduce the life of the device.
Disconnect the unit from power when it is not used.
Never disconnect the product from the power source by pulling on the cord. Do not cut, kink, otherwise damage nor modify the power supply cord and periodically check that it is in good condition.
Wait for the product to cool before cleaning or maintenance.
To clean the product, use only a damp cloth, avoiding solvents or detergents of any kind.
Keep away from children’s reach

ATTENZIONE
**** RISCHIO DI SCOSSA ELETTRICA, NON APRIRE

AVVERTENZA: PER RIDURRE IL RISCHIO DI SCOSSA ELETTRICA, NON TOGLIETE IL COPERCHIO, NON CONTIENE PARTI UTILI PER L’UTENTE. PER L’ASSISTENZA FATE RIFERIMENTO A PERSONALE QUALIFICATO

This symbol alerts you of the presence of important operating and maintenance instructions, in the manual or in the documentation accompanying the product

This symbol alerts you to the presence of uninsulated dangerous voltage within the product’s enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product’s case.

To prevent possible hearing damage, do not listen at high volume levels for long periods.

The CE mark indicates that this product complies with the applicable European directives and their related standards.
Compliance documentation in complete form is available at the company Karma Italian Syl.

Directive 2012/19/UE regarding electric and electronic equipment waste (WEEE). The symbol of the crossed-out dustbin indicates that the product at the end of its life must be collected separately from other waste . The user must , therefore , confer the fixture complete with all the essential components to an authorized disposal center for collection of electronic and electrical waste, or return it to the dealer when buying new equipment of equivalent type, at a rate of one to one, or one to zero if external dimension is less than 25cm. Appropriate separate collection to send the decommissioned equipment to recycling , treatment and environmentally compatible disposal helps to prevent negative impact on the environment and human health and promotes recycling of the materials making up the product. In Italy illegal dumping of the product by the user entails the application of administrative sanctions pursuant to Legislative Decree n. 49 (14/03/2014).

This device is powered by batteries subject to European Directive 2013/56/EU, which cannot be disposed of with normal domestic waste. Find out about the local regulations regarding the separate collection of batteries: a correct disposal allows to avoid negative consequences for environment and health.

EU COMPLIANCE DECLARATION

Hereby, KARMA ITALIANA SRL declares that the amplifiers with Bluetooth PAA 2240 and PAA 2480 are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.karmaitaliana.it.

WARRANTY CONDITIONS
The product is covered by warranty according to current national and European regulations.
For detailed warranty conditions and RMA requests please refer to our website: www.karmaitaliana.it or www.glemm.eu.

The warranty covers manufacturing defects and faults occurred in the first 2 years from the date of purchase. In case of purchase with invoice, the warranty is limited to 1 year.
Damages caused by negligence or wrong use of the device are not covered by warranty.
The warranty is no longer effective if the item is modified or disassembled by not authorized people.
This warranty doesn’t necessarily envisage the product’s replacement.
External components, batteries, knobs, switches and any removable or subject to wear and tear parts are excluded from warranty.
Shipment for the return of faulty items is at expense and risk of the owner.
For all intents and porpuses the warranty is effective only upon exhibition of the invoice or of the purchase receipt.
If you send the product for repair, it must be shipped with complete original packaging: we therefore recommend to save it.

We also suggest to register your product on our website www.karmaitaliana.it, after signing in to access the reserved area.
In this way you will have the possibility to keep track of the warranty validity and to receive updates on our items.

PRODUCT PARTS

PRODUCT PARTS PRODUCT
PARTS

OPTIONAL ACCESSORIES

MULTIMEDIA PLAYER

It offers the possibility to play Mp3 songs from USB sticks and micro SD cards. It includes a bluetooth receiver and a FM radio module. By means of the MODE key you can choose the desired function, while the other keys are used to control the tracks that are being played. The display shows main information on the ongoing song. The multimedia player volume can be adjusted independently, by pressing and holding the “VOL” keys.

MP3

Used to choose on which zone the multimedia player’s signal is to be sent.

MIC/LINE1

Used to choose on which zone the signal connected to the (18) back socket is to be sent.

MIC/LINE2

Used to choose on which zone the signal connected to the (19) back socket is to be sent.

MIC/LINE3

Used to choose on which zone the signal connected to the (20) back socket is to be sent.

AUX

Used to choose on which zone the signal connected to the (17) back socket is to be sent.

ZONE 1

Thanks to the volume keys it is possible to adjust the the zone’s audio level. The MON button sends the desired signal to the RCA back sockets (15). The display will show the selected signal. For better understanding please refer to the chart printed on the right.

ZONE 2

Thanks to the volume keys it is possible to adjust the the zone’s audio level. The MON button sends the desired signal to the RCA back sockets (15). The display will show the selected signal. For better understanding please refer to the chart printed on the right.

CHIME

By pressing this button a bell-like alert signal will be sent to all zones. Just below the key there is a knob to adjust the effect’s volume.

ON/ OFF BUTTON

When the amplifier is on, the led above the key lights up.

POWER SOCKET

Connect here the power cord. Under the socket there is the protection fuse housing. If necessary you can replace it easily. Before opening the housing check that power is disconnected.

ZONE 1 SOCKETS

Connect here the speakers’ cables. In 100V line systems use the “COM” and “+” connectors. In low impedance systems use the “-” and “+” connectors.

If you have doubts on how to connect the speakers turn to a professional installer. Wrong connections could seriously damage the fixtures. From this socket you can pick up the mixed signal sent to zone 1.

ZONE 2 SOCKETS

Connect here the speakers’ cables. In 100V line systems use the “COM” and “+” connectors. In low impedance systems use the “-” and “+” connectors.

If you have doubts on how to connect the speakers turn to a professional installer. Wrong connections could seriously damage the fixtures. From this socket you can pick up the mixed signal sent to zone 2.

LINE OUT

From these sockets you can pick up an RCA stereo signal with the whole mixing of the amplifier.

MONITOR OUT

From this RCA mono socket you can pick up the signal sent by means of the MON (7-8) front button.

EMC IN

You can connect to this RCA socket an external alarm signal.

AUX

It’s a line input with RCA connectors and bass/trebles adjustment.

20) MIC/LINE 1-2-3

Inputs for line or mic signals via 6,3mm or XLR sockets. Thanks to the dipswitches you can select the type of signal and, in case of mic input, it is possible to activate the +48V power supply (only if requested by the microphone). There are also bass and treble controls.