JBL HDI-1600 HDI SERIES Loudspeakers Owner’s Manual
- June 4, 2024
- JBL
Table of Contents
HDI-1600 HDI SERIES Loudspeakers
Owner’s Manual
HDI-1600 HDI SERIES Loudspeakers
THANK YOU FOR CHOOSING THIS JBL® PRODUCT
For more than 60 years, JBL® engineers have been involved in every aspect of
music and film recording and reproduction, from live performances to the
recordings you play on the go and in your home, car, or office.
We’re confident that the JBL system you have chosen will provide every note of
enjoyment you expect – and that when you think about purchasing additional
audio equipment for your home, car, or office, you will once again choose JBL
products.
Please take a moment to register your new product on our Web site,
www.jblsynthesis.com. Registering enables us
to keep you posted on our latest advancements and helps us to understand our
customers and build products that meet their needs.
INCLUDED ITEMS
PLACEMENT
HDI-360013800 FLOOR STANDING LOUDSPEAKER, HDI-1600 BOOKSHELF LOUDSPEAKER For
the best results, place the speakers 6 – 10 feet (1.8m – 3m) apart. Angling
the speakers toward the listening position can improve stereo imaging. The
speakers will produce the most accurate stereo soundstage when the angle
between the listener and the speakers is between 40 and 60 degrees.
Generally,
the bass output will increase as the speaker is moved closer to a wall or
corner.
For the best performance, we recommend that you place the speakers at least 20
inches (51cm) away from the side walls.
HDI-4500 CENTER CHANNEL SPEAKER
You should place the 1-1D1-4500 center speaker directly above or below the
center of your TV screen. The center of the speaker’s horn should be no more
than 2 feet (61cm) above or below the centers of the front left and front
right speakers’ horns. If your TV set is deep enough, you can set the center
speaker on top of the TV, with the speaker’s front edge even with the TV’s
front edge.
Note: You can place HDI-4500 below or above the TV.
Note: For better audio listening performance, please align the center
speaker towards your head level position.
JBL HDI SERIES LOUDSPEAKER – HOME THEATER SPEAKERS 5.1 PLACEMENT SUGGESTION
LAYOUT DIAGRAM
When you use HDI-1600/3600/3800/4500 speakers as surround-channel speakers in
a 5.1-channel system, place them slightly behind the listening position,
facing each other. Ideally, they should be 3 – 4 feet (0.9m – 1.2m) above the
floor. An alternate location would be on a wall behind the listening position,
facing forward. The surround speakers should not call attention to themselves
while they’re playing. Experiment with their placement until you hear a
diffuse, ambient sound accompanying the sounds that you hear from the front
left, front right, and center speakers.
JBL HDI SERIES LOUDSPEAKER – HOME THEATER SPEAKERS 7.1 PLACEMENT SUGGESTION
LAYOUT DIAGRAM
When you use HDI-1600/3600/3800/4500 speakers as surround-channel speakers in
a 7.1-channel system, place the surround side speakers directly to the sides
of the listening position, at least 3 – 4 feet (0.9m – 1.2m) above the floor.
Place the surround back speakers on the wall behind the listening position,
also at least 3 – 4 feet (0.9rn – 1.2m) above the floor and 3 – 6 feet (0.9m –
1.8m) apart.
REMOVING THE GRILLES
You can remove the HDI series loudspeaker grilles by pulling them away from the enclosure.
CONNECTIONS
CAUTION: Make sure that all of the system’s electrical components are
turned OFF (and preferably unplugged from their AC outlets) before making any
connections.
Speakers and amplifiers have corresponding positive and negative (“+” and “-“)
connectors. All HDI series speakers have connectors that are marked “+” and
“-” on the terminal-cup assembly. Additionally, the “+” connectors have red
markings, while the “-” connectors have black markings.
To ensure proper polarity, connect each “+” connector on the back of the
amplifier or receiver to the respective “+” (red) connector on each speaker.
Connect the “-” connectors in a similar way. Do not reverse polarities (i.e.,
“+” to “-” or “-” to “+”) when making connections. Doing so will cause poor
stereo imaging and diminished bass performance.
IMPORTANT: Make sure the “+” and “-” wires or connectors do not touch
each other or the other terminal. Touching wires can cause a short circuit
that can damage your receiver or amplifier.
The HDI series speakers’ gold-plated speaker connectors can accept a variety
of wire connector types. bare wire pin connectors, spade connectors, and
banana connectors.
USING BARE WIRE OR PIN CONNECTORS:
USING SPADE CONNECTORS: USING BANANA
CONNECTORS:
BASIC SINGLE-WIRE CONNECTION
To connect the speakers using a single wire, connect the amplifier to each
speaker as shown in the illustration below. You can use either set of
connectors on the connector panel.
IMPORTANT: Do not remove the metal jumper bars from between the two sets
of connectors when connecting the speaker wires.
BI-WIRE CONNECTION
HDI series loudspeakers connector panels that have two sets of input
connectors are joined by metal jumper bars. The upper set of connectors is for
the compression driver/horn assembly, and the lower set of connectors is for
the woofer(s). This arrangement allows you to bi-wire the speakers using a
single stereo amplifier or using two stereo amplifiers. Bi-wiring can offer
performance advantages and more flexibility in a power-amplifier selection
over a conventional single-wire connection.
Before bi-wiring, the speakers, remove the jumper bars.
SINGLE-AMPLIFIER BI-WIRING
DUAL-AMPLIFIER BI-WIRING
For more information about various speaker-wire and
connection options, contact your local JBL dealer.
CARING FOR YOUR SPEAKERS
- Wipe the cabinet with a clean, dry cloth to remove dust. A damp cloth may dull the cabinet’s finish. Do not use volatile liquids such as benzene, paint thinner or alcohol on the cabinet.
- Do not spray insecticide near the cabinet.
- To remove dust from the grille fabric, use a vacuum cleaner set to low suction.
- Never apply suction or pressurized air to the horn opening.
- Do not wash the grilles in water, as it may fade the color or make it uneven.
- If the surfaces of the woofer cones become dusty, you can carefully sweep them clean with a soft, dry calligraphy brush or paintbrush. Do not use a damp cloth.
SPECIFICATIONS
| MODEL | HDI-1600 | HDI-3600 | HDI-3800 | HDI-4500 |
|---|---|---|---|---|
| DESCRIPTION | 2-way bookshelf loudspeaker | Triple 6.5″, 2.5-way floor-standing | ||
| loudspeaker | Triple 8″, 2.5-way floor-standing loudspeaker | Quad 5.25″, |
2.5-way center channel loudspeaker
ENCLOSURE TYPE| Bass-reflex design with a rear-firing port| Bass-reflex design
with rear-
firing port| Bass-reflex design with rear-
firing port| Bass-reflex design with a rear-firing port
HF DRIVE COMPONENT| 1 inch/ 25mm Teonex compression driver| 1 inch/ 25mm
Teonex compression driver| 1 inch/ 25mm Teonex compression driver| 1 inch/
25mm Teonex compression driver
LF / MF DRIVE components| 6.5-inch/ 165mm black
aluminum cone, cast-frame woofers| 6.5-inch/ 165mm black
aluminum cone, cast-frame woofers| 8-inch / 200mm black aluminum cone, cast-
frame woofers| 5.25-inch / 130mm black aluminum cone, cast-frame woofers
CROSSOVER
FREQUENCY| 1900Hz| 900Hz, 2000Hz| 800Hz, 1800Hz| 600Hz, 2200Hz
SENSITIVITY
(2.83V @ 1M)| 85dB@1m,2.83V| 90dB@1m, 2.83V| 92dB@1m, 2.83V| 90dB@1m, 2.83V
NOMINAL IMPEDANCE| 4 Ohm| 4 Ohm| 4 Ohm| 4 Ohm
RECOMMENDED AMPLIFIER POWER| 150W-200W| 200W-250W| 250W-300W| 200W-250W
Frequency Response| 40 Hz – 30k Hz (-6dB)| 38 Hz – 30k Hz (-6dB)| 37 Hz – 30k
Hz (-6dB)| 50 Hz – 30k Hz (-6dB)
Dimensions
(W x D x H, grille included):| 9.06′ x11.60′ x14.57′
(230 x 294.7 x 370mm )| 10.04′ x13.46′ x38.84′
(255 x 341.9 x 986.5mm )| 11.81′ x16.45′ x43.33′
(300 x 417.8x 1100.5mm )| 33.13′ x12.30″ x7.48′
(841.4 x 312.5x 190mm )
Product Weight
(grille included):| 21.961b(9.96kg)| 61.80Ib(28.03kg)| 83.781b(38.00kg)|
44.331b(20.11kg)
www.jbl.com/specialtyaudio HARMAN
International Industries, Inc.
8500 Balboa Boulevard, Northridge, CA 91329 USA
www.jblsynthesis.com
© 2020 HARMAN International Industries, Incorporated. All rights reserved.
JBL and HDI (High Definition Imaging) are trademarks of HARMAN International
Industries, Incorporated, registered in the United States and/or other
countries.
PolyPlas and Symmetrical Field Geometry are trademarks of HARMAN International
Industries, Incorporated.
Features, specifications, and appearance are subject to change without notice.
Part No. 950-0563-001
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>