DIGITUS DN-95132 PoE Injector Network Switch Installation Guide

DIGITUS DN-95132 PoE Injector Network Switch

Product Information

Product Usage Instructions

• Step 1: Connect the Data Input Port (LAN) of the DN-95132 to your network device (e.g., wireless AP, IPC, switch) using a data cable.
• Step 2: Connect the AC Power Input of the DN-95132 to a power source using the provided 100-240Vac power cable.
• Step 3: Connect the PoE Load Indicator to the device that requires both data and power (e.g., wireless AP, IPC) using a data and power cable.
• Step 4: Verify the Power Indicator on the DN-95132 to ensure it is receiving power.
• Step 5: Check the PoE Load Indicator on the DN-95132 to monitor the PoE load status.

Introduction

DN-95132 is an indoor-rated active PoE midspan

• Injector specially designed for complex backhaul and networking applications. It provides 52Vdc, 0.58A power for remote PDs over 2 pairs output.
• It supports both 10/100 Base-T and Gigabit devices. It works for 30W PoE PDs, such as wireless APs, Wi-Fi routers, Network cameras, IP Phones,
• Microwave Radio and other power Ethernet terminals. It fully complies with IEEE802.3af/at PoE standard.
• Enclosed is an IP40 fire-retardant plastic case.
• Enclosed is an IP40 fire-retardant plastic case.
• It works with a wide input voltage of 100- 240 VAC, 50 or 60 Hz.
• It has a detection chip inside, which will detect and classify PD before powering it.
• It will not provide power until a standard-compliant PD is detected.

Main Features

• Provides 52Vdc, 0.58A power for remote PDs over 2 pairs output
• Supports both 10/100 Base-T and Gigabit device
• Works with a wide input voltage of 100-240 VAC, 50 or 60 Hz.
• Easily merge power and data cables into a single cable
• Each output port has output current limited, short-circuit protection, complete Powered Device (PD) detection and classification
• The Injector can be used independently of the operating system

Package Contents

• DN-95132 PoE Injector
• Power Cord x 1
• Quick Installation Guide x 1

Technical Data

• IEEE802.3 10Base- T Ethernet
• IEEE802.3u 100Base- Tx Fast Ethernet
• IEEE802.3ab 1000Base- T Gigabit Ethernet
• Full compliant with IEEE802.3af/at PoE standard
• Input : 100-240Vac 1.0A 50/60Hz
• Output: 52Vdc 580mA
• Power Pins : 4/5(+), 7/8(-)
• Data Speed : 10/100/1000Mbps
• Operating Temperature: 0°C to 40°C
• Operating Humidity: 20% to 80%, non-condensation
• Storage Temperature: -20°C to 70°C
• Operating Altitude: up to 2000 meters
• Case: Plastic
• Color: White
• IP Rated: IP40
• Size: 107.3mm X 56mm X 34mm
• Weight: 146.8g
• Power Indicator: Yellow
• PoE Load Indicator: Green

Product Description

1. LAN: Data Input Port
2. Power Indicator
3. PoE: Data & Power Output Port
4. PoE Load Indicator
5. AC Power Input

Product Working Diagram

1. Wireless AP
2. IPC
3. 100-240Vac Power
4. Switch
5. DN-95132
   • a. Data and power cable
   • b. 100-240Vac power cable
   • c. Data cable

Hereby Assmann Electronic GmbH declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the manufacturer’s address.

CONTACT

• www.assmann.com.
• Assmann Electronic GmbH
• Auf dem Schüffel 3
• 58513 Lüdenscheid
• Germany

References

• ASSMANN Electronic GmbH | Germany

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>