BORMANN BPG8000 Cordless Disinfectant Sprayer Owner’s Manual
- June 4, 2024
- BORMANN
Table of Contents
BPG8000 Cordless Disinfectant Sprayer
Owner’s Manual
Before using the gun, read this manual thoroughly.
Any improper use can cause damage or seriously hurt, even leading to death.
1 . Explosive view
1 . Nozzle| 12. Left cover of the gun body| 23. Cover clamp
2. Locating Ring| 13. Right cover of the gun body| 24.1eft cover
3Fluid Nozzle| 14. Adjusting bolt| 25. Switch
4. Seal Ring| 15.connector| 26. Right cover
5Needle 1| 16. soft grip 1| 27. Capacitor
6. Needle 2| 17. soft grip 2| 28. Motor
7.0 Ring| 18. soft grip 3| 29. Tension disc
8. Spring| 19. Adjusting module| 30. Power cord
9. Seal Ring| 20. Trigger| 31. Stabiliser
10. PIN| 21. Paint container| 32. Stabiliser
11. Gun Body| 22. Connecting Sleeve|
Technical Data
Voltage: 230-240V/50Hz
110-120V/60Hz
Power consumption: 550W
Motor Speed r.p.m:32,000rpm,
Container Volume: 800mL
Nozzle: 1.8mm
Max. Viscosity: 80 DIN-Secs
Weight: 1.3kgs
Function
Suitable for painting furniture, fences, doors, windows, walls, and ceilings,
and for car repairing, high altitude operation, and so on.
How to use
Before use the electric spray gun, material preparation is the first stage.
Please refer to the thinning chart and picture.
| Material | Run out Time (Sec) |
|---|---|
| 1)Oil enamel | 25-60 |
| 2) Oil-based primer | 30-60 |
| 3)Oil stain | No thinning required |
| 4)Clear sealer | No thinning required |
| 5)Polyurethane | No thinning required |
| 6)Varnish | 20-60 |
| 7)Lacquer sanding sealer | 25-35 |
| 8)Lacquer | 25-35 |
| 9)Automotive finishes | 2J 4C |
| 10)Latex | 45-90 |
1. Unscrew the paint container from the spray gun.
2. Adjust the suction tube.
A) If spray in an upward direction the angled end of the suction tube should
be pointing toward the rear of the gun.
b) If spray is in a downward direction, the angled end of the
suction tube should be pointing towards the front of the gun.
3. Pour material into the container, make sure not to exceed 30 gallons.
4. Remove the motor
Hold the gun with your hand and press the latch in the direction of the arrow.
At the same time hold the motor handle with your hand and rotate it
counterclockwise 90°.
Pull out to remove the motor from the gun.
5）Connect gun body with motor
Hold the gun with your hand to align the slot on the gun with the slot on the
motor and insert it (as shown in the figure).
Hold the motor handle with your hand, and rotate the right-hand clockwise 90°.
When the gun and host are parallel, it is locked.
6）Adjust the needle adjusting screw to meet your requirement.
a) Adjust the screw to the left to decrease paint volume, and lower paint
thickness
b) Adjust the screw to the right to increase paint volume, increase paint
thickness
Spray length adjustment: Turn this knob to adjust the round shape from
vertical to horizontal. Adjust the required length according to the spraying
environment, reduce waste and save material.
The counterclockwise rotation shortens the length, and when it rotates to the
stop position, it is sprayed with the largest circle.
The length is gradually increased when rotated clockwise and is the maximum
length when rotated to the stop position
8) Adjusting spray patterns
a) The gun spray patterns can be changed from a horizontal oval fan pattern to
a round
b) Detailed pattern to a vertical fan pattern by adjusting the nozzle.
9) Open the power switch, pull the trigger, the paint will spray from the
nozzle.
How to spray properly
EVEN COAT THROUGHOUT
Correct:
Keep stroke smooth and at an even speed
Incorrect:
Do not flex wrist while spraying
Warning!
- Keep your workplace clean and tidy, never use the tool in hazardous areas that contain flammable liquids, gasses, or dust.
- Only use paints, solvents, or other materials with a flash point of 73 °F(22C) or higher
- Never point the spray gun at another person or animal. In the event of an injury, seek immediate medical attention.
- Always read the paint manufacturer’s thinning instructions before use.
- You must clean the spray gun thoroughly after each use
- Do not pull the power cord to move this tool.
- The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described/illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
- Please note that our equipment has not been designed for use in commercial, trade, or industrial applications. Our warranty will be voided if the machine is used in commercial, trade, or industrial businesses or for equivalent purposes.
- To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair, or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
Troubleshooting
| Problem | Cause | Solution |
|---|---|---|
| A.little or no material flow | 1. nozzle clogged |
2. suction tube clogged
3. material volume setting turns too far to the right 4. suction tube lose
5. material is too thick
6. inconsistent paint
7. container is loose| 1.clean 2.clean 3.turn to the left
4. insert
5. check the viscosity
6. strain paint
7. tighten the container
B.material leaking| 1. nozzle lose
2. nozzle worn
3. nozzle seal worn
4. material build-up on spray pattern dial and nozzle| 1.tighten 2.replace
3.replace 4.clean
C.atomization is too coarse| 1. viscosity of the material is too high
2. material volume too large
3. nozzle clogged
4. too little pressure build-up in the container| 1. thin
2. turn to the right
3. clean
4. tighten the container
D.spray jet pulsates| 1. Material in the container running out.
2. material is too thick| 1. refill
2. check the viscosity
E.pattern runs or sags| 1. applying too much material| 1. adjust material
flow or increase movement of the spray gun
F.too much over-spray| 1. gun too far from spray object
2. too much material applied| 1. reduce the distance
2. turn the material volume setting to the right
G.pattern is very light and splotchy| 1. moving the spray gun too fast| 1.
adjust material flow or decrease movement of the spray gun
H.large cloud of paint| 1. gun too close to the surface| 1. move the gun
away from the surface and reduce paint flow
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>