DOSTMANN 5020-0350 GT1 Puncture Thermometer Instruction Manual

June 13, 2024
DOSTMANN

5020-0350 GT1 Puncture Thermometer

DOSTMANN 5020-0350 GT1 Puncture Thermometer 5020-0350
Instruction manual
Digital probe thermometer
art. no. 5020-0350

Before you start using it
Please make sure to read the instruction manual carefully.
Following and respecting the instructions in your manual will prevent damage to your instrument and loss of your statutory rights arising from defects due to incorrect use. We shall not be liable for any damage occurring as a result of non following of these
instructions.
Likewise, we take no responsibility for any incorrect readings and for any consequences which may result from them.
Please take particular note of the safety advice!
Please keep this instruction manual for future reference.
For your safety:

  • It should only be used as described in your instruction manual.
  • Keep this instrument and the battery out of the reach of children.
  • Batteries can be fatal if swallowed. If a battery has been swallowed, get medical assistance immediately.
  • Batteries must not be thrown in fire, short-circuited, taken apart or recharged. Danger of explosion!
  • Batteries contain harmful acids. Low batteries should be changed as soon as possible to prevent damage caused by a leaking.
  • Remove the battery if you do not use the instrument for a longer period of time.
  • Do not place your product near extreme temperatures, vibrations or shocks. Protect it from moisture.
  • Never burn the probe directly over fire.
  • Only the probe is heat resistant until 150 °C.
  • Unauthorized repairs, modifications or changes to the product are prohibited.
  • Clean your instrument with a soft damp cloth. Do not use solvents or scouring agents.
  • Do not immerse the display element into water. Water can penetrate into the precision sensor and cause malfunction. Not suitable for dishwasher.
  • Do not use the instrument in the microwave.
  • Be careful when handling the probe. When the device is not used, put the protective cap over the probe.

Getting started / Operation

  • Press the ON/OFF button, to turn on the device.
  • The display shows the currently measured temperature.
  • The sensor is located in the point of the probe.
  • To measure the temperature, insert the probe at least 2,5 cm deep in the object.
  • Press the MAX/MIN button again and the minimum temperature is shown since the last reset (on the display appears MIN).
  • Press the MAX/MIN button again and the maximum temperature is shown since the last reset (on the display appears MAX).
  • It is reset by pressing the ON/OFF button
  • Change the battery when the functions of the device become weak.
  • Open the battery compartment and insert a new battery LR44 polarity as illustrated (+pole above).

Troubleshooting

Problems Solutions
No display Ensure battery polarity is correct (+ pole above)

Change the battery
Incorrect display| Switch on the instrument (ON)
Check the position of the sensor
Change the battery

Waste disposal

**** Never dispose of empty batteries and rechargeable batteries in household waste. As a consumer, you are legally required to take them to your retail store or to an appropriate collection site depending on national or local regulations in order to protect the environment.
The symbols for the heavy metals contained are: Cd=cadmium, Hg = mercury; Pb=lead This instrument is labelled in accordance with the EU Waste Electrical and Electronic Equipment Directive (WEEE). Please do not dispose of this instrument in household waste. The user is obligated to take end-of-life devices to a designated collection point for the disposal of electrical and electronic equipment, in order to ensure environmentally-compatible disposal.

Specifications

Measuring range:  -50°C to +150°C
Operating temperature: -30°C to +50°C
Precision: +/- 1°C  with -30°C …. +150°C, otherwise +/- 2,0°C
Resolution: 0.1 °C
Power consumption: LR 44  button cell (included)
Auto switching-off function: automatically after about 1 hour
Dimensions: 84x26x175 mm
Sensor tube:: 120×5,0 mm
Weight:  41 g (instrument only)

This product fulfills the guidelines according to EN 13485.
Suitability: S, T (Storage, Transport)
Location: E
Accuracy class: 1
Measuring range: -50°C…+150°C
In accordance with EN 13485, this instrument is subject to regular inspections as per
EN 13486(recommendation: yearly)

Technical changes, any errors and misprints reserved. Stand02_CHB2110

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DOSTMANN User Manuals

Related Manuals