Body Solid GFID100 Corner Leverage Gym Owner’s Manual
- June 13, 2024
- BODY SOLID
Table of Contents
Body Solid GFID100 Corner Leverage Gym
HARDWARE INSTRUCTION
PARTS HARDWARE LIST
INSTALLATION STEP
- Be careful to assemble all components
in the sequence they are presented.
NOTE
- Finger tighten all hardware in this step. DO NOT wrench tighten until instructed.
- Some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, they must be wrench tighten to fully go on.
Attach Front Leg (B) to Main Frame (A) using:
- 2 – (#3) M10×95mm Carriage Bolt
- 2 – (#13) M10 Flat Washer
- 2 – (#10) M10 Nylon Lock Nut
Attach Back Leg (C) to Main Frame (A) using:
- 2 – (#3) M10×95mm Carriage Bolt
- 2 – (#13) M10 Flat Washer
- 2 – (#10) M10 Nylon Lock Nut
Attach UiBracket (D) to Main Frame (A) using:
- 1 – (#5) M10×95mm Hex Head Bolt
- 2 – (#13) M10 Flat Washer
- 1 – (#10) M10 Nylon Lock Nut
STEP 1
- Above shows Step 1 assembled and completed.
STEP 2
- Be careful to assemble all components in the sequence they are presented.
NOTE:
- Finger tighten all hardware in this step. DO NOT wrench tighten until instructed. Some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, they must be wrench tighten to fully go on.
Attach Seat and Back Frames (E & F) to Main Frame (A) using:
- 1 – (#2) M12×220mm Hex Head Bolt
- 2 – (#12) M12 Flat Washer
- 1 – (#9) M12 Nylon Lock Nut
- 2 – (#16) 021×012.5×10mm Bushing
- 8 – (#17) 016×012.5x8mm Bushing
Attach Adjustment Bracket (G) to Back Frames (F) using:
- 1 – (#1) M12x165mm Hex Head Bolt
- 2 – (#12 ) M12 Flat Washer
- 1 – (#9) M12 Nylon Lock Nut
- 2 – (#16) 021×012.5x10mm Bushing
Attach Tube (28) to Adjustment Bracket (G) using:
- 1 – (#4) M10x100mm Hex Head Bolt
- 2 – (#13) M10 Flat Washer
- 1 – (#10) M10 Nylon Lock Nut
Attach T-Knob Lock Pin (20) and Pop Pin (21) to Main Frame (A)
STEP 2
Above shows Step 2 assembled and completed.
- Be careful to assemble all components in the sequence they are presented.
NOTE:
- Wrench tighten ALL hardware at the end of STEP 3B. Some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, they must be wrench tighten to fully go on.
Attach Seat Pad (26) to Seat Frame (E) using:
- 4 – (#7) M8×60mm Hex Head Bolt
- 4 – (#14) M8 Flat Washer
- 4 – (#15) M8 Lock Washer
Attach Back Rest (27) to Back Frames (F) using:
- 4 – (#7) M8×60mm Hex Head Bolt
- 4 – (#14) M8 Flat Washer
- 4 – (#15) M8 Lock Washer
Insert two Foam Rollers (23) and two Round End Caps (25) onto U-Bracket (D).
STEP 3
- Above shows Step 3 assembled and completed.
Exploded View
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>