CLAS OC 9137 Rear Parking Sensor Punch Tool Kit Instruction Manual

: June 13, 2024
: CLAS

Table of Contents

CLAS OC 9137 Rear Parking Sensor Punch Tool Kit
Product Information
Product Usage Instructions
COMPONENTS
INTRODUCTION
DESCRIPTION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CLAS OC 9137 Rear Parking Sensor Punch Tool Kit

Product Information

The OC 9137 Kit is a tool set designed for the installation of rear parking sensors in VW/SKODA vehicles. It includes 5 pieces of essential components.
The kit is manufactured by CLAS, a company that specializes in automotive equipment. The product complies with technical specifications and is intended for specific use as described in the manual.
The tool set features centering pins that ensure precise fixing and alignment of the sensor supports during fastening (welding/gluing). It is suitable for standard parking sensors (PDC=Park-Distance-Control) and parking assistance sensors (PLA=Parking Assistant).

Product Usage Instructions

Before starting any action, it is compulsory to read the instruction manual provided.
Ensure you have all the components mentioned in the manual.
Adhere to the vehicle manufacturer’s recommendations and repair instructions.
Use protective work gloves, protective footwear, hard hat, and safety goggles for personal safety.
If you have any issues or questions regarding the product, contact CLAS via email at sav@clas.com or by phone at +33(0)4 79 72 69 18. You can also visit their website at clas.com.
If you have changed your mind about the purchase, return the product before attempting to install it.
Follow the steps below for using the tool set:

Step 1:
Refer to Fig.11 in the manual for a visual representation of the steps.

Step 2:
Refer to Fig.11 in the manual for a visual representation of the steps.

Step 3:
Refer to Fig.11 in the manual for a visual representation of the steps.

Step 4:
Refer to Fig.11 in the manual for a visual representation of the steps.

Step 5:
Refer to Fig.11 in the manual for a visual representation of the steps.

Step 6:
Refer to Fig.11 in the manual for a visual representation of the steps.

Step 7:
Refer to Fig.11 in the manual for a visual representation of the steps.

Step 8:
Refer to Fig.11 in the manual for a visual representation of the steps.

Step 9:
Refer to Fig.11 in the manual for a visual representation of the steps.

Step 10:
Refer to Fig.11 in the manual for a visual representation of the steps.

Step 11:
Refer to Fig.11 in the manual for a visual representation of the steps.

Step 12:
Refer to Fig.11 in the manual for a visual representation of the steps.

For any further assistance or inquiries, please contact CLAS using the provided contact details.

KIT EMPORTE-PIECES CAPTEURS DE
STATIONNEMENT VW/SKODA #2 (5 PCS)
REAR PARKING SENSOR PUNCH TOOL KIT VW/SKODA #2 (5 PCS)

WARNING

Before returning this product for any reason (installation problem, instructions for use, breakdown, manufacturing problem…), please contact us.

Contact :
You can reach us by mail sav@clas.com or by phone +33(0)4 79 72 69 18 or go directly to our website clas.com
If you have changed your mind regarding your purchase, please return this product before you attempt to install it.

COMPONENTS

CLAS-OC-9137-Rear-Parking-Sensor-Punch-Tool-Kit-1

INTRODUCTION

It is compulsory to read this instruction manual before starting any kind of action.
The proper operation and full compliance of this product’s performance is guaranteed only if all the instructions provided in this manual are closely adhered to.
We guarantee that this product complies with the technical specifications described in this manual.
The manufacturer shall not be held responsible for any improper uses other than those described herein.
Use protective work gloves, protective footwear, hard hat and safety goggles.

Misuse:

This product should only be used as described in this documentation; any other use is considered improper.
The manufacturer accepts no responsibility for any damage caused by the incorrect or unreasonable use of the equipment.
Moreover, misuse shall also void the warranty.

Take care of your tools:

Be sure to store your tools in a clean state.
Place the tools inside their original package.

DESCRIPTION

The tool set described in this manual is used to make clean holes in plastic bumpers without burrs. This is necessary when the replacement bumper supplied by the manufacturer does not have the holes for mounting the parking sensors.
According to some manufacturers’ repair instructions, holes should be drilled only after painting to guarantee, once repaired, an appearance as close to the original as possible.
Furthermore, the centering pins contained in the tool set ensure the correct fixing and alignment of the sensor supports during fastening (welding/gluing).
This tool set features a choice of the most used measures, also including odd intermediate measures, as prescribed by different manufacturers. It is suitable for standard parking sensors (PDC=Park-Distance-Control) and for parking assistance sensors (PLA=Parking Assistant).
The OEM numbers shown are used only for assigning technical data and fields of use!

INSTRUCTIONS

Always adhere to the vehicle manufacturer’s recommendations and repair instructions!

As a rule, the position of the sensors is marked by the manufacturer with markings on the inside of the bumpers (Fig.1). The supplied assembly tool set may contain a template suitable for the vehicle and/or the bumper.
Use a Ø10 mm drill to drill a hole for each marking on the bumper.
Place the drill exactly in the middle of the marking and drill from the inside to the outside (Fig.2).
Select the bushing suitable for the hole and insert it on the threaded pin with bearing. The opening of the matrix should face the direction opposite the bearing (Fig.3).
Insert the drive unit with the threaded part into the hole previously drilled in the bumper (Fig.4).
Screw the punch on the drive unit’s thread (Figures 5+6).
Use a 3/8″ ratchet wrench and then a monkey wrench to lock the punch from the outside. The punch is pulled into the bushing as it is screwed (Figures 7+8).
A clean hole is created in the bumper without burrs by working from the outside towards the inside (Fig.9).
Ensure the centering pin is perfectly suited to the sensor support (Fig.10).
From the outside, insert the appropriate centering pin into the hole of the newly cut bumper (Fig.11)..
From the inside, place the sensor support directly on the pin (Fig.12).