CLAS 9123 Rear Parking Sensor Punch Tool Kit Toyota Instruction Manual

CLAS 9123 Rear Parking Sensor Punch Tool Kit Toyota

Product Information

• Product Name: OC 9123 Kit Emporte-Pièces Capteurs de Stationnement Toyota (5 PCS)
• Description: The OC 9123 Kit Emporte-Pièces Capteurs de Stationnement Toyota (5 PCS) is a tool set used for making clean holes in plastic bumpers without burrs. It is designed for situations where the replacement bumper supplied by the manufacturer does not have holes for mounting parking sensors. The kit includes centering pins that ensure the correct fixing and alignment of the sensor supports during fastening (welding/gluing).
• Manufacturer: CLAS Equipements

Contact Information:

• Email: sav@clas.com
• Phone : +33(0)4 79 72 69 18
• Website : clas.com

Product Usage Instructions

1. Always adhere to the vehicle manufacturer’s recommendations and repair instructions.
2. Before attempting to install the product, please return it if you have changed your mind regarding your purchase.
3. Read the instruction manual provided before starting any action.
4. Ensure you have protective work gloves, protective footwear, a hard hat, and safety goggles.
5. Follow the steps provided in the manual for using the tool set to make clean holes in plastic bumpers without burrs.
6. If necessary, use the centering pins included in the kit to ensure the correct fixing and alignment of the sensor supports during fastening.
7. If you encounter any problems or have questions, contact your authorized technician or the reseller for assistance.

WARNING

• Before returning this product for any reason (installation problem, instructions for use, breakdown, manufacturing problem…), please contact us.
• Contact : You can reach us by mail sav@clas.com or by phone +33(0)4 79 72 69 18 or go directly to our website clas.com
• If you have changed your mind regarding your purchase, please return this product before you attempt to install it.

COMPONENTS

INTRODUCTION

• It is compulsory to read this instruction manual before starting any kind of action.
• The proper operation and full compliance of this product’s performance is guaranteed only if all the instructions provided in this manual are closely adhered to.
• We guarantee that this product complies with the technical specifications described in this manual.
• The manufacturer shall not be held responsible for any improper uses other than those described herein.
• Use protective work gloves, protective footwear, hard hat and safety goggles.

Misuse:

• This product should only be used as described in this documentation; any other use is considered improper.
• The manufacturer accepts no responsibility for any damage caused by the incorrect or unreasonable use of the equipment.
• Moreover, misuse shall also void the warranty.

Take care of your tools:

• Be sure to store your tools in a clean state.
• Place the tools inside their original package

DESCRIPTION

• The tool set described in this manual is used to make clean holes in plastic bumpers without burrs. This is necessary when the replacement bumper supplied by the manufacturer does not have the holes for mounting the parking sensors.
• According to some manufacturers’ repair instructions, holes should be drilled only after painting to guarantee, once repaired, an appearance as close to the original as possible.
• Furthermore, the centering pins contained in the tool set ensure the correct fixing and alignment of the sensor supports during fastening (welding/gluing).
• The OEM numbers shown are used only for assigning technical data and fields of use!

INSTRUCTIONS

Always adhere to the vehicle manufacturer’s recommendations and repair instructions!

1. As a rule, the position of the sensors is marked by the manufacturer with markings on the inside of the bumpers (Fig.1). The supplied assembly tool set may contain a template suitable for the vehicle and/or the bumper.

2. Use a Ø10 mm drill to drill a hole for each marking on the bumper. Place the drill exactly in the middle of the marking and drill from the inside to the outside (Fig.2).

3. Select the bushing suitable for the hole and insert it on the threaded pin with bearing. The opening of the matrix should face the direction opposite the bearing (Fig.3).

4. Insert the drive unit with the threaded part into the hole previously drilled in the bumper (Fig.4).

5. Screw the punch on the drive unit’s thread (Figures 5+6).

6. Use a 3/8″ ratchet wrench and then a monkey wrench to lock the punch from the outside. The punch is pulled into the bushing as it is screwed (Figures 7+8).
   A clean hole is created in the bumper without burrs by working from the outside towards the inside (Fig.9).

7. Ensure the centering pin is perfectly suited to the sensor support (Fig.10).

8. From the outside, insert the appropriate centering pin into the hole of the newly cut bumper (Fig.11).

9. From the inside, place the sensor support directly on the pin (Fig.12).

CLAS Equipements ZA de la CROUZA 73800 CHIGNIN FRANCE
Tél. +33 (0)4 79 72 62 22
Fax. +33 (0)4 79 72 52 86
KIT EMPORTE-PIECES CAPTEURS DE STATIONNEMENT TOYOTA (5 PCS)
REAR PARKING SENSOR PUNCH TOOL KIT TOYOTA (5 PCS)
If you need components or parts, please contact the reseller. In case of problems, please contact your authorized technician

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>