CLAS OC 9113 Rear Parking Sensor Punch Tool Kit User Manual
- June 13, 2024
- CLAS
Table of Contents
OC 9113 Rear Parking Sensor Punch Tool Kit
User Manual
OC 9113 Rear Parking Sensor Punch Tool Kit
COMPONENTS
1| PILOT TOOL|
---|---|---
2| DRIFT TOOL|
3| DRILL Ø18 mm|
4| TOOL FOR PUNCHING MACHINE DRIVE 3/8″ WITH BALL
BEARING – M10X1|
MATRIX:
| APPLICATIONS | #18 |
|---|---|
| MODEL | YEAR |
| C-MAX | 2003- |
INTRODUCTION
It is compulsory to read this instruction manual before starting any kind of
action.
The proper operation and full compliance of this product’s performance is
guaranteed only if all the instructions provided in this manual are closely
adhered to.
We guarantee that this product complies with the technical specifications
described in this manual.
The manufacturer shall not be held responsible for any improper uses other
than those described herein. Use protective work gloves, protective footwear,
hard hat and safety goggles.
Misuse:
- This product should only be used as described in this documentation; any other use is considered improper.
- The manufacturer accepts no responsibility for any damage caused by the incorrect or unreasonable use of the equipment.
- Moreover, misuse shall also void the warranty.
Take care of your tools:
- Be sure to store your tools in a clean state.
- Place the tools inside their original package.
DESCRIPTION
The tool set described in this manual is used to make clean holes in plastic
bumpers without burrs. This is necessary when the replacement bumper supplied
by the manufacturer does not have the holes for mounting the parking sensors.
According to some manufacturers’ repair instructions, holes should be drilled
only after painting to guarantee, once repaired, an appearance as close to the
original as possible.
Furthermore, the centering pins contained in the tool set ensure the correct
fixing and alignment of the sensor supports during fastening (welding/gluing).
The OEM numbers shown are used only for assigning technical data and fields of
use!
INSTRUCTIONS
Always pay attention to the repair specifications and instructions provided by the car manufacturer!
- The sensors’ position is usually indicated by the manufacturing marks found on the inside of the bumper. (Fig. 1) There may also be a template suitable for the car or bumper among the components of the adjustment tool set.
- Drill a hole for each mark using the Ø18 mm drill bit. Place the drill bit exactly in the center of the mark and drill from the inside to the outside. (Fig. 2)
- Choose the punching machine that matches the mark on the bumper. Insert the punching machine into the Ø18 mm hole from inside the bumper. Orient the punching machine according to the mark on the bumper. (Fig. 3)
- Now place the matrix on the bumper as follows: position the corresponding matrix on the punch’s shank so that the guide pin (grub screw on the matrix) fits exactly inside the guide groove on the punch’s shank. The matrix should now adhere to the outside of the bumper. Tip: in order to protect the bumper, you can first apply some adhesive tape on the painted surface. (Fig. 4+5)
- At this point the drive unit with the thread is first inserted into the matrix’ coupling and then screwed by hand. (Fig. 6)
Warning: before starting the punching operation, make sure that the mark
is oriented exactly as shown in the figure on the inside of the bumper.
- To perform the punching, connect the 3/8” ratchet wrench provided in the tool set. Act on the ratchet wrench to punch the hole (Fig. 7), which will result in a custom hole for the specific sensor support. (Fig.8+9)
- Then install the sensors in the bumper.
KIT EMPORTE-PIECES CAPTEURS DE
STATIONNEMENT FORD C-MAX CUSTOM (4 PCS)
REAR PARKING SENSOR PUNCH TOOL KIT FORD C-MAX CUSTOM (4 PCS)
If you need components or parts, please contact the reseller. In case of
problems, please contact your authorized technician.
CLAS Equipment’s
73800 CHIGNIN
FRANCE
Tel. +33 (0)4 79 72 62 22
Fax. +33 (0)4 79 72 52 86
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>