SCUBAPRO GALILEO 3 Wrist Dive Computer User Guide
- June 13, 2024
- SCUBAPRO
Table of Contents
SCUBAPRO GALILEO 3 Wrist Dive Computer
BUTTONS:
- Press: The act of pressing and releasing one of the buttons.
- Long-press: The act of pressing and holding one of the buttons for 1 second.
- INITIAL ACTIVATION: The GALILEO 3 is delivered in deep sleep mode where the display is off. You must connect the GALILEO 3 to the charger to activate it before the first dive.
- ACCESS MAIN MENU: Press the top right button 3 times then press the bottom left button to enter.
Button functions at the SURFACE
BUTTONS| TOP LEFT BUTTON| BOTTOM LEFT BUTTON| TOP RIGHT BUTTON| BOTTOM RIGHT BUTTON
Press
|
Dim / brighten backlight
| Enter menu Confirm setting Access current dive
settings (from watch screen)
| Add numerical values Toggle up to previous menu
Shortcut to Sport menu (from watch screen)
| Subtract numerical values Toggle down to next menu Shortcut to Stopwatch
(from watch screen)
Long- press| Shortcut to Logbook (from current dive settings
screen)| Return to previous menu Cancel setting| Start swim mode (from current
dive settings screen)| Shortcut to gas summary table (from current dive
settings screen)
Button functions during DIVING
Press
|
Dim / brighten backlight
| SCUBA: Reset safety timer / Set bookmarks
GAUGE: Reset stopwatch
| SCUBA: Scroll through dive information
GAUGE: Reset average depth
|
SCUBA: Scroll through dive information
Long- press|
Launch compass
| Manual gas switch (PMG mode ON)| Display dive profile Access gas summary table
(PMG mode ON)
| Display dive profile Access gas summary table
(PMG mode ON)
Navigate through the menu with the four push-buttons
TOP LEFT BUTTON (DIM/LIGHT)| BOTTOM LEFT BUTTON (ENTER/RETURN)|
TOP RIGHT BUTTON (SCROLL UP)| BOTTOM LEFT BUTTON (SCROLL DOWN)
The below chart maps out the menu structure and functionality associated with
each mode.
Select from two dive screen configurations — Light or Classic
CHECK YOUR BATTERY
- Your GALILEO 3 is powered by a rechargeable Li-ion battery.
- Always check the battery capacity before each dive.
- If the battery warning appears, charge the battery.
WARNING
Once your GALILEO 3 ’s battery reaches the end of its lifetime, it can only be
replaced by an authorized SCUBAPRO service center. Do not open your GALILEO 3
or try to replace the battery yourself! Opening the GALILEO 3’s housing will
VOID YOUR WARRANTY!
PAIRING YOUR TRANSMITTER
- Mount the first stage regulator with the Smart transmitter on a full tank.
- Set the GALILEO 3 to pairing mode (Other Settings > Gas Integration > Pairing).
- Open the tank valve then place the GALILEO 3 near the transmitter.
- Once pressurized the transmitter will send a pairing sequence to the GALILEO 3.
- When the GALILEO 3 receives this information, the display changes to show a listing of tank designations.
- Scroll to Tank T1. Tank T1 is always the main tank you start your dive with. Save your selection.
- The current pressure of the paired tank will be displayed in either BAR or PSI.
HOW TO POSITION AND USE THE HEART RATE MONITOR
- Position your HR monitor as shown on the left.
- Adjust the strap so that it is comfortable to wear but snug enough to stay in place.
- The HR monitor must be worn directly against the bare skin.
- Moisten the electrode areas if your skin is dry or when diving in a drysuit.
HOW TO ACTIVATE THE HEART RATE FUNCTION ON YOUR GALILEO 3
- Go to menu Other settings > Pair heart rate belt and pair your GALILEO 3 with the heart rate monitor
- Go to Personalization > Workload and select Heart Rate.
- Set your maximum & base HR limits.
- Scroll to Use skin temp. and select ON
- For more information and to view this card in other languages, visit www.scubapro.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>