SHANGRI-LA SLLEDBEDBDA LED Gas Lift Bed Frame User Guide

SHANGRI-LA SLLEDBEDBDA LED Gas Lift Bed Frame

SAFETY & WARNINGS

Ensure to read all instructions and warnings in this user guide prior to assembly.

• When opening the packaging, ensure all components are accounted for. If components are missing, contact help.Kogan.com for assistance.
• Clean the surface using only with a slightly damp cloth, do not use strong abrasive cleaners.
• Using mismatched or incorrect hardware may cause damage to the product. Identify all the hardware and accessories prior to installation.
  Note: The leather fabric tends to get dirty during the packing process, if you receive the item a little flaw, you can wipe it clean with the wet wipes. If there have any problem, please do feel free to contact us.

COMPONENTS

A Headboard (x1)

B Footboard (x1)

C Right sideboard (x1)

D Left sideboard (x1)

E Long slat support (x2)

F Short slat support (x2)

G Centre slat support (x1)

H Support leg (x2)

Hardware

1. Bed base fabric (x1)

2. Feet (x4)

3. M8x20 (x24)

4. M8 Washer (x14)

5. Bracket (x2)

6. Allen Key

7. T-handle Allen Key

8. M8x40 Screw (x14)

9. M8 Nut (x22)

10. Remote receiver (x1)

11. Remote (x1)

12. End Caps (x22)

13. Slats (x22)

14. Inner Caps (x11)

15. Lift handle (x1)

16. Mattress stopper (x1)
    

17. Light strip (x1)

18. Alcohol wipe (x1)

19. Power adapter (x1)
    ASSEMBLY

Step 1

• Screw the feet (2) to the headboard (A) and footboard (B).
• Insert x8 M8x20 screws (3) into the headboard and footboard.

Step 2

• Align the holes on the ends of the footboard (B) with those on the left and right sideboards (C, D).
• Align a bracket (5) with the corner between the left sideboard (C) and footboard (B), then use the Allen key (6) to secure the bracket (5) with x4 M8x20 screws (3).
• Repeat the same process on the corner between the right sideboard (D) and footboard (B).

Step 3

• Connect the x4 frames (E,F) using the M8x20 screws (3), pay attention to the orientation of the left and right-side tube (E).
• Connect the centre support bar (G) to the assembled frame using M8x40 screws (8) and M8 washers (4) on the outside of (F) and secure it with x4 M8 nuts (9).
• Install the support legs (H) to centre bars (G) in the same way, and then tighten it using the Allen key (6) and T-handle Allen key (7).

Step: 4

• Place the slat support assembly onto the gas lifts (on the sideboard) and secure it in place using x6 M8x40 screws (8), x6 M8 washers (4), and x6 M8 nuts (9) in the holes.
• Tighten using the Allen key (6) and T-handle Allen key (7) to secure the screws.

Step: 5
Install the lift handle (15) and mattress stopper (16) to the bed.

Step: 6

• Connect 2 slats (13) together using x1 inner caps (14) and x2 end caps (12) to create a\ slat assembly. Repeat this process for the remaining slats (13).
• Secure the slat assemblies by aligning the holes on the end caps (12) and inner caps (14) with the slots on the bed assembly.

Step: 7
Extend the gas struts (18) on the left and right sideboards (C, D), then tighten the screws.

Step: 8

• Connect the remote receiver (10) to the light strip (17).
• Connect the power adapter (20) to the remote receiver (10).

Step: 9

• Place the bed base fabric (1) onto the bed assembly.
• Attach the strip light (17) to the channel on the outside of the sideboard and footboard.
• Tighten all screws using the Allen key (6) and T-handle Allen key (7). Clean the bed using the alcohol wipe (19).

OPERATION

Remote button controls
The remote is used to control the LED light strip. Refer to the table below for the function of each button:

CUSTOMER SUPPORT

Need more information?
We hope that this user guide has given you the assistance needed for a simple set-up.
For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com.

References

• Kogan Help Centre

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>