SHANGRI-LA SLSERENEUWA Serengeti Entertainment Unit User Guide
- June 3, 2024
- SHANGRI-LA
Table of Contents
SHANGRI-LA SLSERENEUWA Serengeti Entertainment Unit User Guide
SAFETY & WARNINGS
Failure to follow these basic steps can lead to damage that is not covered by your warranty.
-
Read instructions carefully. Ensure no parts are missing.
-
Lay out all the components on a soft surface.
-
Carefully identify each component, especially those that are similar. The most common mistake is getting things back to front.
-
Do not fully tighten screws (leave slightly loose). When the item is fully assembled, tighten the screws but do not over tighten.
-
Separate and identify each component from the hardware pack and rest each one in its proper location before fastening.
-
Do not, for any reason, use a power tool to assemble this product.
Use of power tools may apply greater than excess force on the fixtures, causing damage. Warranty is void if power tools have been used. -
A Phillips head screwdriver (not supplied) is required for assembly.
The user guide enclosed refers to multiple sets of metal slide runners and slide tracks (pictured above separately).
To avoid any damage to these items during transportation, the slide runners and slide tracks have been pre-assembled together in pairs. Each pair includes a slide runner and slide track. Before assembling your new Shangri-La unit, please separate the slide runners from the slide tracks according to the below instructions.
**Step 1: Extend the slide runners apart from the slide track:
**
Step 2: Gently press the plastic release lever on the slide runner while pulling the slide runner and slide track apart from each other:
Step 3: The slide runner and slide track should now be separated. repeat
these steps for all remaining pairs of slide runners and slide tracks:
To adjust your doors to make the gaps more even (optional).
Step 1: Open the door.
Step 2: Adjust the gap between door and side panel.
Loosen the screw slightly. Adjust the hinge to right position (see step 2a & 2b). then tighten the screw.
Step 2a: Move the door in
Push the hinge back slightly.
Step 2b: Move the door out
Pull the hinge forward slightly.
Step 3: Adjust the gap between two doors.
Loosen or tighten the screw slightly to adjust the gap between the door panels (see step 3a & step 3b).
Step 3a: Move the door right
Turn the screw clockwise a little as shown to make the gap smaller
Step 3b: Move the door left
Turn the screw counter clockwise a little as shown to make the gap bigger.
COMPONENTS
No. | Dimensions (mm) | Qty |
---|---|---|
1 | 355 x 383 x 15 | 1 |
2 | 355 x 383 x 15 | 1 |
3 | 355 x 383 x 15 | 1 |
4 | 355 x 383 x 15 | 1 |
5 | 400 x 1800 x 15 | 1 |
6 | 383 x 1800 x 15 | 1 |
7 | 382 x 892 x 15 | 1 |
8 | 80 x 890 x 15 | 1 |
9 | 50 x 1796 x 15 | 1 |
10 | 50 x 892 x 15 | 1 |
11 | 317 x 450 x 15 | 1 |
12 | 317 x 450 x 15 | 1 |
13 | 364 x 432 x 2.5 | 2 |
14 | 151 x 901 x 2.5 | 1 |
15 | 60 x 1760 x 15 | 2 |
16 | 60 x 313 x 15 | 2 |
17 | 60 x 313 x 15 | 2 |
18 | 175 x 890 x 15 | 1 |
19 | 118 x 350 x 12 | 1 |
20 | 118 x 350 x 12 | 1 |
21 | 116 x 848 x 12 | 1 |
22 | 344 x 857 x 2.5 | 1 |
23 | 50 x 335 x 12 | 2 |
ASSEMBLY
Step 1:
Step 2:
Step 3: Use D screws to secure parts as shown. Use a Phillips head
screwdriver to secure A to B for part 18
Step 4:
Step 5:
Step 6:
Step 7:
Step 8:
Step 9:
Step 10: Repeat this process twice for the parts labelled 15.
Step 11:
Step 12:
Step 13:
Step 14:
Step 15:
Step 16:
Step 17: Secure the hinges (J) with the screws (K) to attach the doors.
Repeat for both doors.
Step 18:
Step 19:
Assembly complete.
Contact Us
Need more information?
We hope that this user guide has given you the assistance needed for a simple
set-up.
For the most up-to-date guide for your product, as well as any additional
assistance you may require, head online to
help.kogan.com.