SHANGRI-LA SLSERENBFWA Serengeti Buffet User Guide
- June 4, 2024
- SHANGRI-LA
Table of Contents
SHANGRI-LA SLSERENBFWA Serengeti Buffet
SAFETY& WARNINGS
Failure to follow these basic steps can lead to damage that is not covered by your warranty.
- Read instructions carefully. Ensure no parts are missing.
- Lay out all the components on a soft surface.
- Carefully identify each component, especially those that are similar. Ihe most common mistake is getting things back to front.
- Do not fully tighten screws (leave them slightly loose). When the item is fully assembled, tighten the screws but do not over tighten
- Separate and identify each component from the hardware pack and rest each one in its proper location before fastening.
- Do not, for any reason, use a power tool to assemble this product. The use of power tools may apply greater than the excess force on the fixtures, causing damage. Warranty is void if power tools have been used.
- A Phillips head screwdriver (not supplied) is required for assembly.
The user guide enclosed refers to multiple sets of metal slide runners and slide tracks (pictured above separately). To avoid any damage to these items during transportation, the slide runners and slide tracks have been pre- assembled together in pairs. Each pair includes a slide runner and slide track. Before assembling your new Shangri-La unit, please separate the slide runners from the slide tracks according to the below instructions.
- Step 1: Extend the slide runners apart from the slide track:
- Step 2: Gently press the plastic release lever on the slide runner while pulling the slide runner and slide track apart from each other:
- Step 3: The slide runner and slide track should now be separated. repeat these steps for all remaining pairs of slide runners and slide tracks:
To adjust your doors to make the gaps more even (optional).
-
Step 1: Open the door.
-
Step 2: Adjust the gap between door and side panel.
Loosen the screw slightly. Adjust the hinge to right position (see step 2a &2b). then tighten the screw.
- Step 2a: Move the door in
- Step 2b: Move the door out
-
Step 3: Adjust the gap between two doors.
Loosen or tighten the screw sightly to adjust the gap between the door panels (see step 3a & step 3b).
- Step 3a: Move the door right
- Step 3b: Move the door left
COMPONENTS
Dimensions (mm)
383 X 625 X 15
383 X 625 X 15
383 X 625 X 15
383 X 625 X 15
400 X 1200 X 15
383 X 1200 X 15
382 X 500 X 15
318 X 360 X 15
50 X 1196 X 15
50 X 500 x15
346x 587 x15
346x 587 x15
Dimensions (mm)
328 X 634 X 2.5
241 X 509 X 2.5
387 X 509 X 2.5
60 X 1160 x15
60 X 313 X 15
60 X 313 X 15
193 x498 X 15
148 X 350 X 12
148 X 350 X 12
146x 350 x12
344 X 465 X 2.5
50 X 335 X 12
ASSEMBLY
-
Step 1: Repeat this process for all pieces labelled 19 and 22.
-
Step 2: Repeat this process for all pieces labelled 20 and 21.
-
Step 3: Use D screws to secure parts as shown. Use a Philips head screwdriver to secure A to B tor part 19.
Repeat this step twIce for both drawers. -
Step 4: Repeat this process for both drawers.
-
Step 5:
-
Step 6:
-
Step 7:
-
Step 8:
-
Step 9:
-
Step 10: Repeat this process twice for parts labeled 16.
-
Step 11:
-
Step 12:
-
Step 13:
-
Step 14:
-
Step 15:
-
Step 16: Insert O and P into the shelf position holes.
-
Step 17: Secure the hinges (J) with the screws (K) to attach the doors.
-
Step 18:
-
Step 19:
-
Step 20:
-
Step 21: Move the drawer chest to the final position. Attach the safety strap to the wall Make sure it is firmly attached and make sure it is snug fit.
Need more information?
We hope that this user guide has given you the assistance needed for a simple
set-up. For the most up-to-date guide for your product, as well as any
additional assistance you may require, head online to
help.kogan.com.