inventor V7KI-36WiFiR-U7RS-36 Air Conditioning Systems Remote Controller User Manual
- June 13, 2024
- inventor
Table of Contents
AIR CONDITIONING SYSTEMS
REMOTE CONTROLLER
USER’S MANUAL
** MODELS:**
V7DI-12WiFiR/U7RS-12
V7DI-18WiFiR/U7RS-18
V7DI-24WiFiR/U7RS-24
V7DI-36WiFiR/U7RS-36
V7DI-42WiFiR/U7RS-42
V7DI-50WiFiR/U7RT-50
V7DI-60WiFiR/U7RT-60
V7CRI-12WiFiR/U7RS-12
V7CRI-18WiFiR/U7RS-18
V7KI-18WiFiR/U7RS-18
V7KI-24WiFiR/U7RS-24
V7KI-36WiFiR/U7RS-36
V7KI-50WiFiR/U7RT-50
V7KI-60WiFiR/U7RT-60
LV6DI-12WiFiR
LV6DI-18WiFiR
LV6CI-12WiFiR
LV6CI-18WiFiR
Remote Controller Specifications
| Model | RG10A(D2S) |
|---|---|
| Rated Voltage | 3.0V( Dry batteries R03/LRO3x2) |
| Signal Receiving Range | 8m |
| Environment | -5°C-60°C(23°F-140°F) |
Quick Start Guide
****
NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions and How to Use Advanced Functions
sections of this manual for a detailed description of how to use your air
conditioner.
SPECIAL NOTE
- Button designs on your unit may differ slightly from the example shown.
- If the indoor unit does not have a particular function, pressing that function’s button on the remote control will have no effect.
- When there are wide differentces between “Remote controller Manual” and “USER’S MANUAL” on function description, the description of “USER’S MANUAL” shall prevail.
Handling the Remote Controller
Inserting and Replacing Batteries
Your air conditioning unit may come with two batteries(some units). Put the
batteries in the remote control before use.
- Slide the back cover from the remote control downward, exposing the battery compartment.
- Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
- Slide the battery cover back into place.
****
BATTERY NOTES
For optimum product performance:
- Do not mix old and new batteries, or batteries of different types.
- Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.
BATTERY DISPOSAL
Do not dispose of batteries as unsorted municipal waste. Refer to local laws
for proper disposal of batteries.
TIPS FOR USING REMOTE CONTROL
- The remote control must be used within 8 meters of the unit.
- The unit will beep when remote signal is received.
- Curtains, other materials and direct sunlight can interfere with the infrared signal receiver.
- Remove batteries if the remote will not be used more than 2 months.
NOTES FOR USING REMOTE CONTROL
The device could comply with the local national regulations.
-
In Canada, it should comply with
CAN ICES-3(B)/NMB-3(B). -
In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.
Buttons and Functions
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual.
****
Remote Screen Indicators
Information are displayed when the remote controller is power up.
****
Note: [*] Not all the models can display the fan speed values between
AU-100%.
Note:
All indicators shown in the figure are for the purpose of clear presentation.
But during the actual operation, only the relative function signs are shown on
the display window.
How to Use Basic Functions
ATTENTION
Before operation, please ensure the unit is plugged in and power is
available.
| Select AUTO mode | Set your desired temperature | Turn on the air conditioner |
|---|
****
NOTE:
- In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT function based on the set temperature.
- In AUTO mode, fan speed can not be set.
COOL or HEAT Mode
Select COOL/HEAT mode| Set the temperature| Set the fan speed| Turn on the air
conditioner
---|---|---|---
****
DRY Mode
| Select DRY mode | Set your desired temperature | Turn on the air conditioner |
|---|
****
NOTE: In DRY mode, fan speed can not be set since it has already been automatically controlled.
FAN Mode
| Select FAN mode | Set the fan speed | Turn on the air conditioner |
|---|
****
NOTE: In FAN mode, you can’t set the temperature. As a result , no temperature displays in remote screen.
Setting the TIMER
TIMER ON/OFF – Set the amount of time after which the unit will automatically turn on/off.
TIMER ON setting
Press TIMER button to initiate
the OFF time sequence.| Press Temp. up or down button for
for multiple times to set the desired
time to turn off the unit.| Point remote to unit and wait 1sec,
the TIMER OFF will be activated.
---|---|---
****
NOTE:
- When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24.
- Cancel either function by setting its timer to 0.0h.
TIMER ON & OFF setting (example)
Keep in mind that the time periods you set for both functions refer to hours
after the current time.
****
Example: If current timer is 1:00PM, to set the timer as above steps, the unit will turn on 2.5h later (3:30PM) and turn off at 6:00PM.
How to Use Advanced Functions
Swing function
Press Swing button
****
The horizontal louver will swing up and down automatically when pressing Swing
button.
Press again to make it stop.
Keep pressing this button more than 2 seconds, the vertical louver swing
function is activated. (Model dependent)
LED DISPLAY
Press LED button
Press this button to turn on and turn off the display on the indoor unit.
ECO/GEAR function
Press X-ECO button to enter the energy efficient mode in a sequence of
following:
ECO GEAR(75%) GEAR(50%) Previous setting mode ECO……
Note: This function is only available under COOL mode.
ECO operation:
Under cooling mode, press this button, the remote controller will adjust the
temperature automatically to 24 C/75 F, fan speed of Auto to save energy (only
when the set temperature is less than 24 C/75 F). If the set temperature is
above 24 C/75 F, press the ECO button, the fan speed will change to Auto, the
set temperature will remain unchanged.
NOTE:
Pressing the ECO button, or modifying the mode or adjusting the set
temperature to less than 24 C/75 F will stop ECO operation.
Under ECO operation, the set tmeperature should be 24 C/75 F or above, it may
result in insufficient cooling. If you feel uncomfortable, just press the ECO
button again to stop it.
GEAR operation:
Press the ECO/GEAR button to enter the GEAR operation as following:
75%(up to 75% electrial energy consumption)
↓
50%(up to 50% electrial energy consumption)
↓
Previous setting mode.
Under GEAR operation, the display on the remote controller will alternage
between electical energy consumption and set temperature.
Silence function
Keep pressing Fan button for more than 2 seconds to activate/disable Silence
function.
Due to low frequency operation of compressor, it may result in insufficient
cooling and heating capacity. Pressing ON/OFF, Mode, Sleep, Turbo or Clean
button while operating will cancel silence function.
8°C function
Press this button 2 times during one second under HEAT Mode and setting
temperature of 16 C/60 F or 20 C/68 F.
The unit will operate at high fan speed (while compressor on) with temperature
automatically set to 8 C/46 F.
Pressing On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel
this function.
LOCK function
****
Press together Clean button and Turbo button at the same time more than 5
seconds to activate Lock function.
All buttons will not response except pressing these two buttons for two
seconds again to disable locking.
SET function
****
- Press the SET button to enter the function setting, then press SET button or TEMP or TEMP button to select the desired function. The selected symbol will flash on the display area, press the OK button to confirm.
- To cancel the selected function, just perform the same procedures as above.
- Press the SET button to scroll through operation functions as follows:
Sleep( ) Follow Me( ) AP mode( ****)
Sleep function( ) :
The SLEEP function is used to decrease energy use while you sleep (and don t
need the same temperature settings to stay comfortable). This function can
only be activated via remote control.
For the detail, see sleep operation in USER S MANUAL.
Note: The SLEEP function is not available in FAN or DRY mode.
Follow me function( ):
The FOLLOW ME function enables the remote control to measure the temperature
at its current location and send this signal to the air conditioner every 3
minutes interval.
When using AUTO, COOL or HEAT modes, measuring ambient temperature from the
remote control(instead of from the indoor unit itself) will enable the air
conditioner to optimize the temperature around you and ensure maximum
comfort.
NOTE: Press and hold Turbo button for seven seconds to start/stop memory
feature of Follow Me function.
If the memory feature is activated, On displays for 3 seconds on the screen.
If the memory feature is stopped, OF displays for 3 seconds on the screen.
While the memory feature is activated, press the ON/OFF button, shift the mode
or power failure will not cancel the Follow me function.
AP function( ****) :
Choose AP mode to do wireless network configuration. For some units, it
doesn’t work by pressing the SET button. To enter the AP mode, continuously
press the LED button seven times in 10 seconds.
All the pictures in the manual are for explanatory purposes only. The actual
shape of the unit you purchased may be slightly different, but the operations
and functions are the same.
The company may not be held responsible for any misprinted information. The
design and the specifications of the product for reasons, such as product
improvement, are subject to change without any prior notice.
Please consult with the manufacturer at +30 211 300 3300 or with the Sales
agency for further details. Any future updates to the manual will be uploaded
to the service website, and it is advised to always check for the latest
version.
Scan here to download the latest version of this manual.
www.inventorairconditioner.com/media-
library
AIR CONDITIONING SYSTEMS REMOTE CONTROLLER
Manufacturer: INVENTOR A.G. S.A.
24th km National Road Athens – Lamia & 2 Thoukididou Str.,
Ag.Stefanos, 14565
Tel.: +30 211 300 3300, Fax: +30 211 300 3333 –
www.inventor.ac
References
- Κλιματιστικά Inverter WiFi, Ψυγεία, Αφυγραντήρες, Air Conditioners - Inventor
- Biblioteca media - Inventor
- Media Library & Support - Inventor
- Media Library & Support - Inventor
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>