FW MURPHY ITX-150-6 IntelliSpark Integral Coils Instruction Manual
- June 13, 2024
- FW MURPHY
Table of Contents
FW MURPHY ITX-150-6 IntelliSpark Integral Coils
Product Information:
The product covered by these instructions is the IntelliSpark coils. The specific part numbers for these coils are:
- ITX-150-6
- ITX-170-10
- ITX-150-12
- ITX-170-12
- ITX-170-6
- ITX-250-12
The IntelliSpark coils are integral coils that are designed to mount directly
to specially threaded spark plugs or adaptors. It is important to properly
install these coils to ensure their expected life expectancy and performance.
Incorrect installation can lead to
damage to the spark plug and potential contamination and heat damage to the
coil.
Product Usage Instructions
- Ensure that the spark plugs have been installed according to the OEM’s recommendations before proceeding with the coil installation.
- NEVER torque the spark plugs using the integral coil.
- Screw the coil onto the already properly installed spark plug until it is fully seated.
- Tighten the coil firmly by hand.
- Using a torque wrench, tighten the coil to a torque value between 5 – 10 ft.-lbs. Never exceed 10 ft.-lbs.
- DO NOT use any thread lubricant between the coil and the spark plug.
By following these usage instructions, you will ensure proper installation and usage of the IntelliSpark coils, maximizing their performance and longevity.
Installation Instructions
WARNING! Deviation from these instructions may lead to improper engine operation which could cause personal injury to operators or other nearby personnel.
The IntelliSpark coils covered by these instructions are part numbers:
- ITX-150-6
- ITX-150-12
- ITX-170-6
- ITX-170-10
- ITX-170-12
- ITX-250-12
Integral coils mount directly to specially threaded spark plugs or adaptors. Proper installation must be used to obtain the designed life expectancy and performance of these coils. Excessive torque applied to the coil during installation could damage the internal seals of the spark plug, which can lead to contamination and/or heat damage to the coil from combustion leakage.
Integral Coil Installation
Once the spark plugs have been installed as per the OEM’s recommendations, the
coils can be installed. NEVER torque the spark plugs using the integral coil.
Screw the coil onto the already properly installed spark plug until it is
fully seated. Tighten the coil firmly by hand and then using a torque wrench,
tighten the coil to 5 – 10 ft.-lbs. of torque. Never exceed
10 ft.-lbs. DO NOT use any thread lubricant between the coil and the spark
plug.
In order to consistently bring you the highest quality, full-featured
products, we reserve the right to change our specifications and designs at any
time.
FW MURPHY product names and the FW MURPHY logo are proprietary trademarks.
This document, including textual matter and illustrations, is copyright
protected with all rights reserved. (c) 2021 FW MURPHY. A copy of our typical
warranty may be viewed or printed by going to
www.fwmurphy.com/warranty.
FW MURPHY PRODUCTION CONTROLS
SALES, SERVICES & ACCOUNTING
4646 S. HARVARD AVE.
TULSA, OK 74135
MANUFACTURING
2151 RANDON DYER ROAD
ROSENBERG, TX 77471
5757 FARINON DRIVE
SAN ANTONIO, TX 78249
DOMESTIC SALES & SUPPORT
FW MURPHY PRODUCTS
PHONE: 918 957 1000
EMAIL: INFO@FWMURPHY.COM
WWW.FWMURPHY.COM
FW MURPHY CONTROL SYSTEMS & SERVICES
PHONE: 281 633 4500
EMAIL: CSS-SOLUTIONS@FWMURPHY.COM
INTERNATIONAL SALES & SUPPORT
CHINA
PHONE: +86 571 8788 6060
EMAIL: INTERNATIONAL@FWMURPHY.COM
LATIN AMERICA & CARIBBEAN
PHONE: +1918 770 8775
EMAIL: INTERNATIONAL@FWMURPHY.COM
SOUTH KOREA
PHONE: +82 70 7951 4100
EMAIL: INTERNATIONAL@FWMURPHY.COM