LITHONIA LIGHTING PCNY LED Petroleum Canopy Instruction Manual
- June 13, 2024
- LITHONIA LIGHTING
Table of Contents
**LITHONIA LIGHTING PCNY LED Petroleum Canopy Instruction Manual
**
Protect yourself. Before installing, read the entire instructions carefully and save them for future reference.
Date installed
Failure to follow any of these instructions could void product warranties. For a complete list of product Terms and Conditions, visit www. acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising out of improper or careless installation or handling of its products.
Upon receipt of fixture, thoroughly inspect for any freight damage. All damage should be reported to the delivery carrier. Compare the catalog description listed on the packing slip with the fixture label on the inside of the housing to be sure you have received the correct merchandise.
Mounting Hardware and Silicone Sealant
Required
Purchase Separately
REQUIRED TOOLS:
-
Description
-
Adjustable wrench
-
Philips Head Screwdriver
-
3in Hole saw
-
Drill
-
Caulk Gun
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW THESE SAFETY INSTRUCTIONS!
- To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
- Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
- Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.
- For Residential installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electical code.
- Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.
- This fixture is intended to be connected to a properly installed and grounded UL listed junction box.
- It will occasionally be necessary to clean the outside of the refractor/ lens. Refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.
- DO NOT INSTALL DAMAGED PRODUCT! This luminaire has beenproperly packed so that no parts should have been damaged duringtransit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
- Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
- These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.
WARNING
RISK OF ELECTRIC SHOCK
- Disconnect or turn off power before installation or servicing.
- Verify that supply voltage is correct by comparing it with the luminaire label information.
- Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
- All wiring connections should be capped with UL approved wire connectors.
CAUTION
RISK OF INJURY
- Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
- Avoid direct eye exposure to the light source while it is on.
WARNING
RISK OF BURN
- Allow lamp/fixture to cool before handling. Do not touch enclosure, lens or light source.
- Do not exceed maximum wattage marked on luminaire label.
- Follow all manufacturer’s warnings, recommendations and restrictions including but not limited to: driver type, burning position, mounting locations/methods, replacement and recycling.
- Use only lamps that comply with ANSI standards.
CAUTION
RISK OF FIRE
- Keep combustible and other materials that can burn, away from lamp/ lens.
- Do not operate in close proximity to persons, combustible materials or substances affected by heat.
CAUTION
RISK OF PRODUCT DAMAGE
- Never connect components under load.
- Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
- Unless individual product specifications deem otherwise: Never connect an LED product directly to a dimmer packs, occupancy sensor, timing device, or other related control devices. LED fixtures must be powered directly off a switched circuit.
- Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some volume of airspace around the fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or cooling.
- Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient temperature.
- Only use fixture in its intended location.
- LED products are Polarity Sensitive. Ensure proper Polarity before installation.
- Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of unit.
- Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
- Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative for assistance.
- Changes or modifications not expressly approved by Acuity Brands Lighting could void the authority to operate the equipment.
- Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when used in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
5-YEAR LIMITED WARRANTY
Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www. acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising out of improper or careless installation or handling of its products.
INSTALLATION INSTRUCTIONS
FIXTURE PACKING LIST
A Canopy Luminaire | 1 |
---|---|
B Driver Box | 1 |
C Trim | 1 |
D Threaded pipe with 2 Locknuts | 1 |
E M6 350mm M6 or #14×2-1/4” Mounting screws* | 4 |
F Wire Nuts & Wire ties | 3 |
G Mounting Plate* | 1 |
*Contained in parts packs
Remove fixture components and parts pack. Check to ensure all parts are included. Note: Account for small parts and destroy packing material, as these may be hazardous to children.
Turn OFF Power at fuse or circuit breaker box!
CAUTION: Do not rely on wall switch alone to turn off power.
This fixture is intended for petroleum canopy applications
For mounting to standard steel canopy decks: Drill 3 inch diameter thru- hole in the deck centered between two canopy ribs. Note: Ensure the area on top of the canopy deck is clear of obstructions and will support the weight of the luminaire.
Prepare fixture for installation: Set fixture lens facing down on a protected, flat surface. Hold cord taught and slide threaded pipe towards fixture hub. Use an adjustable wrench to screw the threaded pipe into the fixture hub. See Fig. A.
Install Luminaire to deck: Insert the threaded pipe into the thru-hole from below the deck and hold the fixture flush against the deck.
Use (4) mounting screws (E) provided to secure fixture to canopy deck with 4
.4in-lbs max. torque. DO NOT OVER TORQUE SCREWS. Note: Fixture provides 2
screw spacing options to accomodate different deck plank widths. See Fig. B.
On top of deck, remove the locknuts from the threaded pipe and screw the mounting plate (C) onto the threaded pipe until it is tight against the deck. Then thread one locknut back onto the threaded pipe. Note: Apply silicone sealant along edge of Mounting plate to prevent water entry
Install Driver Box to Luminaire: Remove driver box (B) KO appropriate for your application. Loosen screw on front of driver box and open hinged top of box. Pull fixture cord extending from threaded pipe through the center hole in the bottom of the driver box and slide driver box down the threaded pipe until it rests on the locknut. Thread second locknut onto the threaded rod protruding inside the driver box to secure. **See Fig. C.
**
Connect LED wires to driver:
Use wire nut to connect the green ground wire from the cord to the yellow/
green fixture ground wire in the driver box cover. Locate the two 2-terminal
connectors in the driver box and insert the
Red LED+ and Black LED- wires from the cord in the terminal with the corresponding wire flag marking.
CAUTION: WIRING
Make sure power is turned off.
Thread power supply wires through previously removed knockout. Note: Install
appropriate water tight fittings (not provided)
Connect the bare copper or green house supply ground wire to the yellow/ green fixture ground wire. Note: If house wiring does not include a ground wire, consult your local electrical code for approved grounding methods. Locate the two 3-terminal connectors in the driver box and connect the black/Line fixture wire to the black power supply wire and the white/Neutral fixture wire to the white/Neutral supply wire.
Use provided wire tie for wire management of incoming supply wires.
Turn on electricity at fuse or circuit breaker box and verify success of installation.
Luminaires with ALO provide an adjustable lumen switch located in the
driver box. Factory set to highest lumens “H”(13,000lm). If lower lumens are
desired choose “M” for 10,000lm or “L” for 7,500lm. See Fig D
Install trim: Align decorative trim below Luminare and push up to snap into place. **See Fig. E.
**
Trouble Shooting Guide
If this fixture fails to operate properly, use the guide below to diagnose and correct the problem.
- Verify that power is turned on at switch and breaker
- Verify that line voltage is correct
- Check wiring and connections.
If further technical assistance is required, contact:
Technical Support at: 800-705-7378
Cleaning and Maintenance
Caution: Be sure fixture temperature is cool enough to touch. Do not clean or
maintain while fixture is energized.
This LED light provides low maintenance service with no bulbs to change. Clean surfaces with mild soap and water. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
WARNING: There are no user serviceable parts inside fixture.
Acuity Brands Lighting, Inc.
One Lithonia Way, Conyers, GA 30012
www.AcuityBrands.com
References
- Acuity Brands | Lighting, Controls, and Building Management Solutions
- Acuity Brands | Lighting, Controls, and Building Management Solutions
- U.S. Environmental Protection Agency | US EPA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>