teesa TSA8076 Rechargeable Soap Dispenser Owner’s Manual

teesa TSA8076 Rechargeable Soap Dispenser

Product Information

The TSA8076 is a rechargeable soap dispenser designed for household use. It features an ON/OFF button, a LED diode, a microUSB port for charging, a spout, a motion sensor, and a soap container. The dispenser is compatible with both liquid and foam soap, although foam soap is recommended for better results. It is important to avoid using the dispenser in extreme temperatures and to keep it away from direct sunlight and sources of heat. The appliance should be placed on a dry, flat, and stable surface.
The device comes with safety instructions, including keeping it out of reach of children, avoiding dropping or subjecting it to strong impacts, not placing it in water or any liquid, and not attempting to repair it yourself. In case of damage, it is recommended to contact an authorized service point for check- up/repair.

Product Usage

1. Charging:
   • Connect one plug of the included USB cable to the micro USB port of the soap dispenser.
   • Connect the other plug to the AC charger and then plug it intov a wall outlet.
   • During charging, the red LED will be on. When the battery is fully charged, the LED will turn off.
   • Disconnect the USB cable from the charger and the dispenser.
   • Note : It is recommended to charge the device regularly, every 2 months. When the battery level gets low, the amount of foam dispensed decreases. When that occurs, please charge the device.
2. Filling the Container:
   • The foaming soap dispenser is compatible with liquid or foam soap.
   • It is recommended to use foam soap for better results.
   • To dilute ordinary liquid soap, the recommended ratio of water to soap is 4:1 (depending on the used liquid).
   • Avoid using liquids that are too thick and do not use granular or pearlescent soaps.
   • Separate the container from the dispenser.
   • Pour soap (and water in case of liquid soap) inside the container. Do not overfill as this may cause dripping.
   • Replace the container.
3. Usage:
   • Press the ON/OFF button to turn on the device. The white LED will be on for a while.
   • Place your hands under the spout to activate the motion sensor.
   • For the first-time use, it may be necessary to repeat this process several times until the foam soap begins to dispense.
   • The device will automatically dispense foam soap when it senses motion under the spout within the required distance. The white LED will be on during dispensing.
   • Wash your hands.
   • Press the ON/OFF button to turn off the device. The red LED will be on for a while.

SAFETY INSTRUCTIONS

1. Read this instruction manual carefully, even if you are familiar with the appliance. Keep the manual for future reference.
2. Avoid using/storing the product it in extreme temperatures. Do not expose it to direct sunlight and sources of heat.
3. Product intended for household use only.
4. Do not use the product for purposes different from displayed in this operating manual.
5. Keep the appliance out of the reach of children.
6. Place the appliance on a dry, flat and stable surface.
7. Do not drop the device or subject it to strong impacts.
8. Do not place the appliance in water or any liquid; nor handle/use it with wet or moist hands.
9. Do not attempt to repair this appliance yourself. Never disassemble this appliance.
10. In case of damage, contact with an authorized service point for checkup/ repair.

PRODUCT DESCRIPTION

1. ON/OFF button/ LED diode
2. microUSB port (charging)
3. Spout
4. Motion sensor
5. Soap container

CHARGING

1. Connect one plug of the included USB cable to the micro USB port of the soap dispenser; connect the other plug to the AC charger and then to the wall outlet.
2. During charging, red LED is on. When the battery is fully charged, the LED goes off.
3. Disconnect the USB cable from the charger and the dispenser.

Note : It is recommended to charge device regularly, every 2 months. When the battery level gets low, the amount of foam dispensed decreases. When that occurs please charge the device.

FILLING THE CONTAINER

The foaming soap dispenser is compatible with liquid or foam soap. It is recommended to use a foam soap to achieve better results. To dilute ordinary liquid soap, the ratio of water to soap is recommended to be 4:1 (depending on used liquid). Avoid using liquids that are too thick. Do not use with granular or pearlescent soaps.

1. Separate the container from the dispenser.
2. Pour soap (and water in case of liquid soap) inside the container. Do not overfill as this may cause dripping.
3. Replace the container.

USE

1. Press the ON/OFF button to turn on the device. White LED is on for a while.
2. Place your hands under the spout to activate the motion sensor. For the first time use, it may be necessary to repeat this process several times until the foam soap begins to dispense. The device will automatically dispense foam soap (white LED is on during dispensing). When the device is on, it will dispense foam soap every time it senses motion under the spout within the required distance.
3. Wash your hands.
4. Press the ON/OFF button to turn off the device. Red LED is on for a while.

CLEANING AND STORAGE

• Prior to cleaning, make sure the device is switched off.
• Gently wipe the housing of the dispenser with a soft, slightly damp cloth. Wipe the motion sensor with a soft, dry cloth.
• Clean the inside of the soap container by rinsing it under running water. Leave it to dry completely in an open air.

SPECIFICATION

• Applicable liquid: foam soap / liquid soap
• Capacity: 260 ml
• Reaction time: approx. 0,25 s
• Protection class: IPX4
• Material: ABS
• Working temperature: -10°C – 40°C
• Working humidity: 0 – 85%
• Charing port: micro USB
• Charging time: 2 – 3 hours
• Battery capacity: 500 mAh
• Power: 3 W
• Power supply: 3,7 V / 0,5 A
• In set: USB cable
• Weight: 146 g
• Dimensions: 165 x 100 x 65 mm
• Water to soap ratio: 4:1 (depending on soap)

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwolińska 1, 08-400 Miętne.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>