Bartscher TR I3WL1350 Heat Bridge User Manual

PCI/4711 – PCI/4712 – PCI/4713
User Manual

WARMING SURFACES WITH INFRARED LAMPS
ATTACHMENTS
Spare parts catalogue Wiring diagram

GENERAL INFORMATION

Purpose of the manual
This manual was written by the Manufacturer and is an integral part of machine equipment. During design and construction the Manufacturer has carefully considered possible hazards and personal risks that may result from interaction with the machine. In addition to observing the specific laws in force, the manufacturer has adopted all “exemplary construction technique principles”. The purpose of this information is to advise the users to use extreme caution to avoid risks. However, discretion is invaluable. Safety is also in the hands of all the operators who interact with the machine. Keep this manual in a suitable place, always within reach for consultation. The following symbols are included to better stress some passages:
**DANGER – WARNING: indicates hazards that may cause serious damages; attention is required.
INFORMATION:** indicates particularly important technical information.
The following is enclosed with this manual:

• Warranty certificate describing the Manufacturer’s warranty conditions.
• Documents that prove conformity with effective health and safety laws.

Contact the Authorised dealer for any service request, information or spare parts order.
Manufacturer and machine identification

Warming surfaces with infrared lamp description
This product is specifically designed to keep the temperature of food placed over the heating surfaces constant. It is characterized by a highly simplified construction in order to reduce the possibility of malfunctions to a minimum and facilitate maintenance.
The heating surface is fully constructed with stainless steel AISI 304 18/10 with galvanized steel sheet metal bottom cover.
The resistance is attached under the heating surface.
The heating surface is distinguished by infrared lamps placed above the surface to increase its already high heating capacity.
4 rubber feet can be applied to the bottom of the heating surface for support and insulation.
Controls to turn on the machine and set temperature are found on the long side of the surface.
Technical specifications

Descriptions| Unit of measure| PCI 4711| PCI 4712| PCI 4713
---|---|---|---|---
Power supply| V  Hz  Ph| 230V 50Hz     1Ph
Nominal power| W| 500| 1000| 1500
Net weight| Kg| 10| 17| 25
Packaged weight| Kg| 14| 22| 30
Installation| | Counter
Protection level| | IPX4
Electrical shock protection| | Class I
Conformity with directives and norms| | 73/23/EEC – 93/68/EEC – 93/44/EEC – 89/336/EEC 89/109/EEC

Overall dimensions

mm| A| B| C|
---|---|---|---|---
PCI4711
PCI4712
PCI4713| 60
65
70| 50
85
125| 85
85
85
mm| A| B| C|
PCI4711
PCI4712
PCI4713| 460
620
620| 510
860
1270| 780
780
780

Safety information

• Careful consultation of this manual before installation and use is essential. Continual observance of the indications found in the manual guarantee personal and machine safety.
• Never tamper with safety devices for any reason.
• Strict observance of the work safety regulations issued by the responsible organizations in each country is strongly recommended.
• The manufacturer is not liable for damages to persons or things due to the neglect of safety regulations.
• Correct machine placement, illumination and cleanliness are important conditions for personal safety.
• Do not expose the machine to the elements.
• Machine connections and start-up must only be performed by qualified technicians.
• Make sure that the system specifications of the room where the machine is installed correspond to the information printed on the plate.
• Make sure the machine is connected to a grounding system.
• The work area around the machine must always be kept clean and dry.
• Use the garments foreseen by work safety regulations.
• This machine must only be used for its specific purpose; any other use is considered improper and therefore hazardous.
• Do not overload the machine.
• Introducing objects, tools, hands or other within hazardous parts is forbidden.
• Keep the machine away from children.
• Disconnect the power cord from the electrical socket when the machine is not in use.
• In the event of malfunctions and/or problems, do not attempt to repair the machine. Contact the authorised dealer.
• Use original spare parts.
• Before cleaning the machine, disconnect the power supply by unplugging the machine.
• Do not clean with running water.

INSTALLATION INFORMATION

Packaging and unpacking
The machine is packaged in cardboard with polystyrene inserts to guarantee full integrity during transport.

• Handle the packaging according to the instructions.
• Open the packaging and check the integrity of all components. Keep packaging for future moves.
• Lift the machine as indicated and place it in the installation area.

Installation area
The arranged area must be suitably illuminated and an electrical socket must be available. The resting surface must be sufficiently ample, even and dry. The machine must be installed in rooms with non-explosive environments. In any case, installation must also be performed in consideration of the work safety laws in force.
Room conditions table

room temperature between 20÷60 °C
Dustiness| Less than 0.03 g/m³

Electrical connections
DANGER – WARNING: Electrical connections to the supply mains must be performed by qualified personnel.
Verify the efficiency of the grounding system in the building. Make sure that line voltage (V) and frequency (Hz) correspond to those of the machine (See the identification plate and wiring diagram). The machine is equipped with a power cord that connects to a multi-polar plug. The plug is to be connected to a wall switch equipped with a circuit breaker.

USE AND CLEANING INFORMATION

Control descriptions

• Indicator light (B)
• Adjustable thermostat 0°- 90°C (C)
• Loaded circuit breaker (A) with tension led
• Power cord inlet (D) + cord

Recommendations for use
Before using the machine remove, if found, the special protective film.
Unpleasant odours produced during the first minutes of operation are due to the presence of processing grease residues.
On first use, heat the machine to the maximum temperature.
Warming surfaces with infrared lamps use
Connect the power cord to the main switch and turn the thermostat graduated knob to set the desired temperature. The led will stay on until the surface reaches the previously set temperature.
End of the day cleaning

• Remove the plug from the electrical socket at the end of the day.
• Accurately clean using neutral products.
• Clean external machine parts with a damp sponge when the machine is fully cooled.
• Do not use metallic pads and abrasive detergents.
• To avoid hazards caused by contact with high temperature parts, only access heating parts after maintenance operations have been completed.

Extended periods of disuse
For extended periods of disuse, turn off the main wall switch, clean the machine and cover it with a cloth to protect if from dust.

TROUBLE SHOOTING, RECYCLING

Introduction
In the event of breakdown or malfunctioning, disconnect the plug from the socket and contact your Dealer’s service centre. Avoid dismantling internal machine parts.
The manufacturer is not liable for any machine tampering!
Problems, causes, solutions

Disposal and recycling
The machine was designed and constructed to work for an average of 10.000 hours. When finished using the machine, follow national laws for disposal and recycling.
Please contact the environmental authorities or authorised organizations.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>