VEVOR 14-36 Portable Sawmill User Manual
- June 13, 2024
- VEVOR
Table of Contents
VEVOR 14-36 Portable Sawmill
Product Information
Portable Sawmill
The Portable Sawmill is a versatile tool that allows you to create a portable mill wherever you need it. It is designed to be attached to a chainsaw, enabling you to cut planks from logs with ease. The sawmill comes in three sizes: 24 inches, 36 inches, and 48 inches, allowing you to choose the appropriate size for your needs. It can accommodate chainsaw bars ranging from 14 inches to 48 inches in length. The maximum log diameter that can be processed is 45 inches, and the sawmill can cut planks from 0.2 inches to 11.81 inches in thickness.
Product Usage Instructions
- Before operating the Portable Sawmill, read the entire user manual carefully.
- Ensure that you have assembled the sawmill correctly by following the provided instructions.
- Attach the Portable Sawmill to your chainsaw by inserting two M8x75 bolts through the adjustment post and into the clamping bracket. Make sure the side of the adjustment post with measurements is facing away from you during assembly. Leave the bolts loose to create a gap for the saw bar.
- Slide two M8x75 bolts through the adjustment post and then through the nose guard and clamping bracket. Start hex head bolts into nuts on the bottom of the bracket. Again, leave the bolts loose to allow for mounting the chainsaw bar.
- Attach the thrust and post assembly to the end bracket using a U-clamp, post clamp, two i washers, and coupling nuts.
- Secure the handle at the thrust end flush with the end bracket using a pan head and lock nut.
- Repeat the same process for the nose end, but do not tighten the nut yet.
- Attach the tie bar and grip handle to the off bar using carriage bolts and a coupling nut. Then, attach the unit to the thickness rails using two bolts, flat washers, and nuts.
- Once the Portable Sawmill is properly assembled, carefully follow all safety rules and precautions listed in the user manual.
If you have any product questions or need technical support,please feel free to contact us at [email protected].
Technical Support and E-Warranty Certificate
https://www.vevor.com/support
PORTABLE SAWMILL（36 IN / 48 IN）
USER MANUAL
We continue to be committed to offering tools at competitive prices. “Save Half”, “Half Price”, or any other similar expressions used by us only represent an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and do not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when placing an order with us if you are saving half in comparison with the top major brands.
WARNING:
Read carefully and understand all ASSEMBLY AND OPERATION
INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
INTEND USE
Attach the portable chainsaw sawmill to your chainsaw to create a portable
mill where you need it most.
TECHNICAL SPECIFICATIONS
| ITEM | Description（24in.） | Description（36in.） | Description（48in.） |
|---|---|---|---|
| SIZE | 24” | 36” | 48” |
FITS
| Chainsaw bars 14”
to 24”
| Chainsaw bars 14”
to 36”
| Chainsaw bars 14”
to 48”
Log Diameter| ****
21in.
| ****
33in.
| ****
45in.
THICKNESS
| Cut plank from 0.2” to 11.81” thick| Cut plank from 0.2” to 11.81” thick| Cut plank from 0.2” to 11.81” thick
GENERAL SAFETY RULES
- WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in serious injury.
- CAUTION: Do not allow persons to assemble this Mower Display Rack until they have read this manual and have developed a thorough understanding of how the Mower Display Rack works.
- WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS
WORK AREA
- Keep work area clean, free of clutter and well lit.Cluttered and dark work areas can cause accidents.
- Keep children and bystanders away while assembling Lumber mill
- Be alert of your surroundings. Using a Lumber mill in confined work areas may put you dangerously close to cutting tools and rotating parts.
ASSEMBLY
Step 1
Insert two M8x75 bolts (item#19) through adjustment post (item#1) and into clamping bracket(make sure the side of the adjustment post with measurements on it is facing away from you when assembling)(item#2)engaging nuts on bottom of clamping braket. leave loose so there is a gap for the saw bar!
Step 2
Insert two M8x75 bolts (item#19)through adjustment post(item#5). Slide bolts
through nose guard (item #11) and through clamping braket(item#6).
Start hex head bolts(item#19) into nuts on bottom of braket. leave loose so
there is a gap for mounting chainsaw bar!
Step 3
Attach thrust and post assembly t end bracket using U-clamp (item#12) post camp (item#13) two i washer (item#18),and coupling nuts(item#17).
Step 4
Secure handle at thrust end fiush with end bracket using pan head(item#21)and lock nut (item#22).
Step 5
The same applies to the nose end but do not tighten nut(same Step 3 and Step 4).
Step 6
Attach tie bar (item#8) and grip handle (item#3) to an-off bar (item#7) using carage boits (item #16). Coupling nut (item #17)then attach unit to thickness rails (item #10) using two bolts (item #16) flat washer (item #18) and nuts (item#17).
Step 7
Attach end bracket (item#4) to thickness rails(item#10) using carriage boits (item#19) two flat washer and Couping Nut (item#17). Tighten hex nuts finger tight only. Attach 2nd end bracket (item#4) to thickness rail (item#10) using two bolt(item#16), washer and nuts (item#17) now tighten hex nuts. Be sure that end brakets are flush with thickness rails.
New function
You can use the scew (item#20) to fix the Chain saw to Clmp. Brkt/Nose End
(item#6) , so it can make the Chain saw firm.
Manufacturer: Yongkang Jinjian Hardware Factory
Address: 11 Huabao Road, Zhiying Industrial Zone II, Yongkang City,Zhejiang Province, China
Technical Support and E-Warranty Certificate
https://www.vevor.com/support
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us:
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.