SATCO 64-100 LED Rgbtw Indoor Outdoor Tape Lights Installation Guide

LED RGBTW INDOOR/OUTDOOR
TAPE LIGHTS
Models: 64-100, 64-110, 64-111, 64-120, 64-121, 64-130, 64-131, 64-132,
64-133, 64-134, 64-135, 64-140, 64-141, 64-142, 64-143, 64-144, 64-145

64-100 LED Rgbtw Indoor Outdoor Tape Lights

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.

WARNING: Risk of Fire or Electric Shock

• This tape lighting is only intended to be used with the products provided in the kit.
• Installation requires knowledge of luminaries electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
• To reduce risk of fire and over-heating, secure all connections.
• TURN OFF the electrical power before proceeding.
• The electrical rating of this product is 120V/60Hz.
• The grounding and banding of the system shall be done in accordance with National Electric Code (NEC) Article 600 and local codes.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Do not damage any PCB conductive parts, squeeze or fold the LED tape light when installing.
• Pay attention to positive and negative polarities before installation, otherwise the LED tape light may be damaged.
• Prevent static electricity when installing. Avoid damp or wet exposure.
• This device is not intended for use with emergency exits.

CUTTING
Applies to indoor models only 64-100, 64-110, 64-111, 64-120,
64-121, 64-130, 64-131 , 64-132, 64-133, 64-134, 64-135.

• Always disconnect the power supply before cutting. LED strips can be cut as indicated in diagram.

Indoor Installation

Applies to models 64-100, 64-110, 64-111 , 64-120, 64-121, 64-130, 64-131 , 64-132, 64-133, 64-134, 64-135.

STEP 1: Clean surfaces carefully (free from grease and dust) before installing to ensure that the double sided tape or adhesive sticks properly to the surface.
Wood, powder-coated, structured surfaces, glass, stainless steel etc. are not recommended locations.

STEP 2: Gently peel off the tape, the adhesive tape may tear by over stretching.

STEP 3: Wearing an anti-static ring, gently press PCB areas.
Do not press down on the actual LEDs.

STEP 4: Be careful to not step on the reel if you unreel the entire strip before installation.

Outdoor Installation

Applies to models 64-140, 64-141, 64-142, 64-143, 64-144, 64-145. Use included brackets to install the tape.
There is no double-sided adhesive with these models.

CONNECTIONS

STEP 1: Align white arrow on the controller’s cable to [ ] symbol on LED strip.
STEP 2: Connect controller to the power supply or Junction Box.
NOTE: Actual controller appearance may vary .

Wiring Diagram

STEP 3A: Plug the power supply into a power outlet.
STEP 3B: For Junction Box, shut OFF power at the circuit breaker.
Connect wires as shown in wiring diagram above. Make sure all wire connectors are secure. After wires are connected, tuck them carefully inside the Junction Box and turn ON power.

Operation

Use the remote control or Starfish APP to control the light strip; such as to turn on and off, brightness and color change.

Manual Control by 3 Buttons & IR Remote Control

SYSTEM REQUIREMENTS

• Minimum iOS 9.3 or Wi-Fi 4.4
• Dedicated 2.4GHz Wi-Fi Network

TECHINCAL SUPPORT
support@satcostarfish.com

DOWNLOAD THE STARFISH APP

https://smartapp.tuya.com/satcosmart

(App design is subject to change without notice.)

**REGISTER YOUR ACCOUNT

**

Verify you’re connected to a 2.4GHz Wi-Fi Network.
Launch the STARFISH app and tap “Sign-up” to create a new account or “Login” to your existing account.
Enter email address, then select “Get verification code”.

Enter verification code that was sent to your email.

CREATE A HOME

Tap the “Me” button at the bottom of the screen, and then “Home Management”.
Select the Create a home button to set up your home.

ADD A DEVICE

Tap the(+) button on the top right corner to access the action menu, then select “Add Device” .

Select device type from the listed categories.

PAIR A DEVICE WITH WI-FI

To put the device into pairing mode, press and hold the power button for approximately 5 seconds until the tape light starts flashing, then release the button. The device is now ready to be paired .

Select your 2.4GHz Wi-Fi Network name and enter password then click “Next.”

The pairing status screen will appear.

PAIR A DEVICE WITH WI-FI/BLUETOOTH

Note: Verify your mobile device is connected to a 2.4GHz Wi-Fi Network and that you have Bluetooth turned ON for connection.
For Wi-Fi/Bluetooth enabled devic­es, you will see a pop-up indicating that there are unpaired devices in the area. The device does not need to be in pairing mode.
Tap “Add” and select the devices you would like to connect.

Once all the devices have connected, tap “Next”.

Once device is successfully paired, continue to step 10.
When successfully connected, you may rename the device. Tap the “Pen” icon, enter the new name and select “Done”. The device is now ready to be controlled with the STARFISH app.

Note: If pairing is unsuccessful, please refer to the FAQs on Satco.com/Starfish
Bluetooth is strictly used to pair and connect the device. A 2.4GHz
Wi-Fi Network is required to operate all STARFISH products.

SHARE A HOME

From the Home Management screen, select the Home that you would like to share.
Tap “Add Member” and select the way that you would like to send the invitation

Enter the user information and select if the new member will be an “Administrator” or a  Common Member” in the Home.
Tap “Save” to send the invitation.

To view the entire STARFISH product line visit Satco.com/STARFISH

Scan QR Code to learn more

http://www.satco.com/starfish NUVO 64-132
TAPE/RGBTW-HO/IP20/PLUG/SF/64′

General

Status| Active
Fixture Type| Tape Light
Finish| White
Wattage| 68W
Lumen Output| 6300L
IP Rating| IP20
Indoor or Outdoor Fixture| Indoor
Smart Product Info
IOT Enabled| Yes
Voice Assistants Supported| Google Home; Alexa; Siri; SmartThings
Specifications
Technology| LED
Color Temperature| RGB and Tunable White
CRI| 80+
Voltage| 24V
Rated Hours| 50000
Operating Temperature| -20C (-4F) to +40C (+104F)
Dimmable| Yes-Dimmable
Dimming Note| Only with Starfish App or Remote
Control
Weight (lb.)| 2.42
Material| Plastic
Dimensions
Width (in.)| 0.47
Length (in.)| 787.44
Compliance
Safety Listing| cETLus – Listed
Location Rating| Dry
0| No
Energy Star| No
DLC Approved| T20 Exempt – Fixtures Not
CA T20 / T24 Rationale| Regulated
California Status| Lawful for sale in California
Title 20 / 24 Status| Lawful for sale
California Prop 65| Lead
RoHS Compliant| Yes
FCC Compliant| Yes
SDS Sheet| LED_Fixture
Additional Information
Additional Information| Driver Wattage is 72W; Driver Voltage is 120V
Specification Note| Cuttable: Yes; Distance between cuts: 4.92″ (125  mm); High Brightness; Sync to Music
Installation Notes| 2 reels of 32 feet (10M) to make 64 feet (20M) total;  9 Foot (3M) plug in tape pre-installed on back for  quick installation Kit includes: Plug-in Driver;

SUPPORT CENTER >> 1 Year Limited – Fixtures

This Satco Products, Inc. product is warranted to be free from defects in materials and workmanship for a period of 1 year from date of original purchase. The warranty does not cover damage caused by abuse, misuse, improper environmental conditions, wrong installation or shipping damage. If this does not last, return with proof or purchase, register receipt with your name & address, For replacement. This replacement is the sole remedy available and liability  for incidental or consequential damages is hereby expressly excluded. This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions  supplied with the product. Satco does not warrant and specially disclaims any warranty, whether expressed or implied, of fitness for a particular purpose, other than the warranty contained herein. Satco specifically disclaims any liability  and shall not be liable for any consequential or incidental loss or damage, including any labor / expense costs involved in the replacement or repair of said product.

For More Information Visit:
http://www.satco.com/ 

References

• SATCO/NUVO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>