SATCO 64-100 Series LED RGBTW Tape Light Installation Guide
- June 13, 2024
- SATCO
Table of Contents
SATCO 64-100 Series LED RGBTW Tape Light
Product Information
LED RGBTW Indoor/Outdoor Tape Lights
Models: 64-100, 64-110, 64-111, 64-120, 64-121, 64-130, 64-131, 64-132, 64-133, 64-134, 64-135, 64-140, 64-141, 64-142, 64-143, 64-144, 64-145
Satco Products, Inc. Brentwood, NY 11 717
The LED RGBTW Indoor/Outdoor Tape Lights are versatile lighting fixtures that can be used both indoors and outdoors. They come in various models to suit different requirements.
These tape lights provide a combination of RGB (red, green, blue) colors and warm white light. They are designed to be easy to install and offer various modes and brightness levels for customization.
Product Usage Instructions
Indoor Installation
Applies to models: 64-100, 64-110, 64-111, 64-120, 64-121, 64-130, 64-131, 64-132, 64-133, 64-134, 64-135
- Clean the installation surface thoroughly to ensure proper adhesion of the double-sided tape or adhesive. Avoid surfaces such as wood, powder-coated structures, glass, and stainless steel.
- Gently peel off the tape from the strip, being careful not to overstretch or tear the adhesive tape.
- Wear an anti-static ring and press gently on the PCB areas of the strip. Avoid pressing directly on the LEDs.
- If you need to unreel the entire strip before installation, be cautious not to step on the reel.
Outdoor Installation
Applies to models: 64-140, 64-141, 64-142, 64-143, 64-144, 64-145
Use the included brackets to install the tape lights. These models do not come with double-sided adhesive.
Connections
- Align the white arrow on the controller’s cable with the [ + – ] symbol on the LED strip.
- Connect the controller to the power supply or Junction Box. Note that the appearance of the controller may vary.
Refer to the provided wiring diagram for connecting the wires correctly. If using a Junction Box, make sure to shut off power at the circuit breaker before connecting the wires. Secure all wire connectors and carefully tuck the wires inside the Junction Box before turning on power.
Operation
To control the light strip, you can use either the included remote control or the Starfish APP.
Manual Control by Remote Control:
- Press the ON/OFF button once to turn the lights on or off.
- Adjust brightness and speed using the buttons marked “C”.
- Change mode type using the “M” button. There are 8 mode options available.
- To reset and put the lights into network pairing mode, press and hold the reset button for 5 seconds.
Control via Starfish APP:
- Download the Starfish APP from Google Play or the App Store. (Note: App design may change without notice.)
- Ensure you are connected to a 2.4GHz Wi-Fi network.
- Launch the Starfish APP and sign up or login to youraccount.
- Tap on the “Me” button at the bottom of the screen, then select “Home Management” to control your lights.
Contact Technical Support at support@satcostarfish.com for further assistance.
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING: Risk of Fire or Electric Shock
-
This tape lighting is only intended to be used with the products provided in the kit.
-
Installation requires knowledge of luminaries electrical systems. If not qualified, do not attempt installation. Contact
a qualified electrician. -
To reduce risk of fire and over-heating, secure all connections.
-
TURN OFF the electrical power before proceeding.
-
The electrical rating of this product is 120V/60Hz.
-
The grounding and banding of the system shall be done in accordance with National Electric Code (NEC) Article 600
and local codes. -
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
-
Do not damage any PCB conductive parts, squeeze or fold the LED tape light when installing.
-
Pay attention to positive and negative polarities before installation, otherwise the LED tape light may be damaged.
-
Prevent static electricity when installing. Avoid damp or wet exposure.
-
This device is not intended for use with emergency exits.
CUTTING
Applies to indoor models only 64-100, 64-110, 64-111, 64-120, 64-121, 64-130, 64-131 , 64-132, 64-133, 64-134, 64-135.
- Always disconnect the power supply before cutting. LED strips can be cut as indicated in diagram.
Indoor Installation
Applies to models 64-100, 64-110, 64-111 , 64-120, 64-121, 64-130, 64-131 , 64-132, 64-133, 64-134, 64-135.
STEP 1: Clean surfaces carefully (free from grease and dust) before
installing to ensure that the double sided tape or adhesive sticks properly to
the surface. Wood, powder-coated, structured surfaces, glass, stainless steel
etc. are not recommended locations.
STEP 2: Gently peel off the tape, the adhesive tape may tear by over stretching.
STEP 3: Wearing an anti-static ring, gently press PCB areas. Do not press down on the actual LEDs.
STEP 4: Be careful to not step on the reel if you unreel the entire strip
before installation.
Outdoor Installation
Applies to models 64-140, 64-141, 64-142, 64-143, 64-144, 64-145. Use included brackets to install the tape. There is no double-sided adhesive with these models.
CONNECTIONS
STEP 1: Align white arrow on the controller’s cable to [ +-] symbol on LED strip.
STEP 2: Connect controller to the power supply or Junction Box.
NOTE: Actual controller appearance may vary .
Wiring Diagram
STEP 3A: Plug the power supply into a power outlet.
STEP 3B: For Junction Box, shut OFF power at the circuit breaker. Connect
wires as shown in wiring diagram above. Make sure all wire connectors are
secure. After wires are connected, tuck them carefully inside the Junction Box
and turn ON power.
Operation
Use the remote control or Starfish APP to control the light strip; such as to
turn on and off, brightness and color change.
Manual Control by 3 Buttons & IR Remote Control
- Adjust Brightness/Speed.
- Press one time ON/OFF.
- To reset and put into network pairing mode, press and hold for 5 seconds.
- Change mode type(8 mode options).
SYSTEM REQUIREMENTS
- Minimum iOS 9.3 or Wi-Fi 4.4
- Dedicated 2.4GHz Wi-Fi Network
TECHINCAL SUPPORT
DOWNLOAD THE STARFISH APP
(App design is subject to change without notice.)
REGISTER YOUR ACCOUNT
-
Verify you’re connected to a 2.4GHz Wi-Fi Network.
-
Launch the STARFISH app and tap llill “Sign-up” to create a new account or “Login” to your existing account.
-
Enter email address, then select “Get verification code”.
-
Enter verification code that was sent to your email. CREATE A HOME
-
Tap the “Me” button at the bottom of the screen, and then “Home Management” Select the “Create a home” button to set up your home.
ADD A DEVICE -
Tap the(+) button on the top right
- corner to access the action menu, then select “Add Device”.
- corner to access the action menu, then select “Add Device”.
-
Select device type from the listed categories.
PAIR A DEVICE WITH WI-FI -
To put the device into pairing mode, liil press and hold the power button for approximately 5 seconds until the tape light starts flashing, then release the button. The device is now ready to be paired.
-
Select your 2.4GHz Wi-Fi Network lilil name and enter password then click “Next.” The pairing status screen will appear.
PAIR A DEVICE WITH WI-FI/BLUETOOTH
Note: Verify your mobile device is connected to a 2.4GHz Wi-Fi Network and that you have Bluetooth turned ON for connection. -
For Wi-Fi/Bluetooth enabled devicliil es, you will see a pop-up indicating that there are unpaired devices in the area. The device does not need to be in pairing mode.
Tap “Add” and select the devices you would like to connect.
-
Once all the devices have lilil connected, tap “Next
-
Once device is successfully paired, continue to step 10.
-
When successfully connected, you\ may rename the device. Tap the “Pen” icon, enter the new name and select “Done”. The device is now ready to be controlled with the STARFISH app.
-
Note: If pairing is unsuccessful, please refer to the FAQs on Satco. com/Starfish
-
Bluetooth is strictly used to pair and connect the device. A 2.4GHz Wi-Fi Network is required to operate all STARFISH products.
SHARE A HOME
From the Home Management screen, select the Home that you would like to share. Tap “Add Member” and select the way that you would like to send the invitation
Enter the user information and select if the new member will be an “Administrator” or a 11Common Member” in the Home.
Tap “Save” to send the invitation.
Scan QR Code to learn more
To view the entire STARFISH product line visit Satco.com/STARFISH
General
- Status: Active
- Fixture Type: Tape Light
- Finish: White
- Wattage: 20W
- Lumen Output: 1920L
- IP Rating: IP20
- Indoor or Outdoor Fixture: Indoor
Smart Product Info
IOT Enabled: Yes
Voice Assistants Supported: Google Home; Alexa; Siri; SmartThings
Specifications
- Technology: LED
- Color Temperature: RGB and Tunable White
- CRI: 80+
- Voltage: 24V
- Rated Hours: 50000
- Operating Temperature: -20C (-4F) to +40C (+104F)
- Dimmable: Yes-Dimmable
- Dimming Note: Only with Starfish App or Remote Control
- Weight (lb.): 3.41
- Material: Plastic
Dimensions
- Width (in.): 0.47
- Length (in.): 196.85
Compliance
- Safety Listing: cETLus – Listed
- Location Rating: Dry
- Energy Star: No
- DLC Approved: No
- CA T20 / T24 Rationale: T20 Exempt – Fixtures Not
- Regulated California Status: Lawful for sale in California
- Title 20 / 24 Status: Lawful for sale
- California Prop 65: Lead
- RoHS Compliant: Yes
- FCC Compliant: Yes
- SDS Sheet”: LED_Fixture
Additional Information
-
Additional Information: Driver Wattage is 30W; Driver Voltage is 120V-277V
Specification Note -
Cuttable: Yes; Distance between cuts: 4.92″ (125 mm); High Brightness; Sync to Music
Installation Notes -
1 reel of 16 feet (5M); 9 Foot (3M) plug in tape pre-installed on back for quick installation
Includes -
Kit includes: Driver/Junction Box; Controller/Receiver; IR Remote; 1-
Warranty
- Warranty 1 Year Limited – Fixtures
- Copyright 2020 Satco Products, Inc. All Rights Reserved
- http://www.satco.com/
This Satco Products, Inc. product is warranted to be free from defects in materials and workmanship for a period of 1 year from date of original purchase. The warranty does not cover qdamage caused by abuse, misuse, improper environmental conditions, wrong installation or shipping damage. If this does not last, return with proof or purchase, register receipt with your name & address, For replacement. This replacement is the sole remedy available and liability for incidental or consequential damages is hereby expressly excluded. This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. Satco does not warrant and specially disclaims any warranty, whether expressed or implied, of fitness for a particular purpose, other than the warranty contained herein. Satco specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including any labor / expense costs involved in the replacement or repair of said product.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>