AIDA PTZ-X12-IP Full-HD Optical Zoom PTZ User Manual

Full-HD Optical Zoom PTZ
PTZ-X12-IP | PTZ-NDI-X12 | PTZ-X20-IP
PTZ-NDI-X20 Manual

PTZ-X12-IP Full-HD Optical Zoom PTZ

The information within this manual is subject to change at any time without prior notice*

Safety Guide

1. Before operation, please read all of the instructions in the manual carefully. For your convenience, please keep this manual.
2. The camera power input range is 100-240VACv(50-60Hz). Ensure the power supply input is within this rate before powering on.
3. Camera power voltage = 12VDC,rated currency= 2A.Wesuggestyou use it with the original power supply adapter supplied by the factory.
4. Please keep the power cable, video cable, and control cable in a safe place and out of obstructions.
5. 0perationalenvironment: 0°C-50°C/32°F-122°F,with humidity levels less than 90%.To avoid any damage, do no put or pour anything inside the camera.
6. Avoid weight stress, vibration, and pressure on the camera during transportation, storage, and installation.
7. Do not remove the camera housing or cover. Doing so will void the warranty.
8. Do not direct the camera towards strong/intensive light. Doing so could cause irreversible damage to the camera and void warranty.
9. Use a dry and soft cloth to clean the camera housing with a neutral cleaning agent, when needed. To avoid damage on the camera lens, do not use strong or abrasive cleaning agents on the camera housing.
10. Do not move the camera by moving the camera head. To avoid mechanical trouble, do not rotate the camera head by hand. Please refrain from moving the camera while it is in motion. Doing so could cause irreversible damage to the camera and void warranty.
11. Make sure the camera is on a fixed and balanced platform. Avoid any slanted placements.
12. Power Supply Polarity Schematics:

Warning:
Video quality can be affected by specific frequencies of electromagnetic field.
Never grasp the head of the camera. Never move the camera by hand while is in motion. Doing so can damage the mechanism.

Packing List

Check the items below, when opening the package:

| – AIDA PTZ
– Power Adapter
– Power Cable
– RS-232 Control
Cable
– USB 3.0 Cable| – Remote Control
– User Manual
– Double Sided Adhesive
– QC Certification
– Wall Mount
---|---|---

Quick Start

1. Check that all cable connections are secure before powering on the camera.
2. Dial Switch Setting (Used for Camera Updates):

Dial Switch (ARM)

| SW-1| SW-2| Mode
1| OFF| OFF| Updating Mode
2| ON| OFF| Debugging Mode
3| OFF| ON| Undefined
4| ON| ON| Working Mode
Dial Switch

| SW-3| SW-4| Instruction
1| OFF| OFF| Reserve
2| ON| OFF| Reserve
3| OFF| ON| Reserve
4| ON| ON| Reserve
Dial Switch (USB)

| SW-5| SW-6| Instruction
1| OFF| OFF| Undefined
2| ON| OFF| Working Mode
3| OFF| ON| Updating Mode
4| ON| ON| Undefined

Product Highlights

• Contains an advanced Sony Progressive CMOS Sensor providing 1920×1080 Ultra HD resolution.
• Wide angle optical lens: 12x / 20xoptical zoom
• Full HD video over IP, via H.264or H.265 encoding.
• Contains traditional outputs such as HDMI, SDI, USB3.0, as well as RJ-45 for RTSP/RTMP streaming.
• Support line in function, supporting ACC and LPCM audio coding.
• Fully adjustable camera settings, such as White Balance, Exposure Settings, and Image Parameters.
• Supports P0E: use a single CAT 5/6 cable to control and output video via the RJ-45port.
• Fast and precise focusing performance when zooming or moving the camera head.
• Smooth PTZ movements, as well as little to no motor sound when moving.
• Supports 10presets viaremoteor128presetsviaRS-232oronline interface.
• Standard Sony Serial VISCA, IP VISCA protocol, as well as IP VISCA over UDP.
• Daisy chain is supported via the RS-232 input and output, controlling a maximum of 7 cameras.
• Menu based image parameters, including image flip for ceiling mounted cameras.
• Remote has multiple functions, such as fast switching video formats and ability to change IP address.
• Free firmware updates to keep the camera up to date with the latest and greatest!
• The USB3.0 port is compatible with USB2.0 and allows standard UVC1.5 protocol for local control. UVC control works seamlessly with many well-known conferencing software.
• PTZ Menu supports both English and Spanish
• Supports NDI® | Hex transmission (PTZ-NDI-X12 and PTZ-NDI-X20) only.

Camera Specs

Video Format| HDMI (V 1.4)| 1920 x 1080 60p/59.94p/50p/30p/29.97p/25p/24p/23.98 1920 x 1080 60i/59.94i/50i 1280 x 720 60p/59.94p/50p/30p/29.97p/25p
---|---|---
SDI| 1920 x 1080 60p/59.94p/50p/30p/29.97p/25p/24p/23.98 1920 x 1080 60i/59.94i/50i 1280 x 720 60p/59.94p/50p/30p/29.97p/25p
USB| 1920 x 1080 60p/50p/30p/25p (USB 3.0)
1280 x 720 60p/50p/30p (USB 3.0)
1280x72025p(USB3.0&2.0)
1024×576 30p(USB3.0 & 2.0)
960 x 540 30p (USB 2.0)640 x 360 30p (USB 2.0)
512 x 28830p (USB 2.0)
RJ-45| 1920 x 1080 @ 1~60 1280x 720 @ 1~60 (Main Stream)
1280×720@1~60/1027×576@1~60(Sub Stream)
Video Interface| HDMI (V 1.4) 3G-SDI, RJ-45, USB 3.0
---|---
Sensor| SONY Progressive CMOS Sensor
Zoom| 12x or 20x 0ptical Zoom
Lens| F4.9~98mm (20x), F1.5-3.0, View Angle:61°(Far)-3.2°(Near)
Rotation Angle| Pan: -170°~+170°; Tilt: -30°~+90°
Rotation Speed| Pan: 0°~120°/s; Tilt: 0°~80°/s
Preset| Remote Controller: 10 RS-232: 128
Control Port| RS-232, RJ-45 (VISCA over IP), USB 3.0 (UVC 1.5), USB 2.0 (UVC 1.1)
Network Speed| 1000M
Video Encode| H.264/H.265 (default: H.264)
Bit Rate Control| Variable Bit Rate, Constant Bit Rate
Video Bit Rate| 1024kbps(min)~20480 kbps(max)
IP Protocol| IP, HTTP, RTSP, RTMP, DCHP, 0NVIF, VISCA over IP (UDP)
P0E| Supported (IEEE802.3af)
Line in| Supporting ACC audio coding
Daisy Chain| Support RS-232 serial daisy chain
Minimum Lux| 0.01 Lux
White Balance| Auto/Indoor/0utdoor/Manual/ATW/0ne Push/Fluorescent Lamp/Sodium Lamp
Exposure| Auto/Manual/Bright/Shutter/Iris
Focus| Auto/Manual
Iris| Auto/Manual
Gamma| Supported
WDR| Supported
BLC| Supported
2D Noise Reduction| Supported
3D Noise Reduction| Supported
Anti Flicker| 0FF/50Hz/60Hz
Image Flip| Supported
Image Voltage| DC12V / PoE (24W)
Dimension| 220mm x 173mm x 190mm/8.66″ x 6.81″ x 7.48″
Net Weight| 1.4kg/3.1lbs

Camera Interface

1. Camera Lens
2. Camera Base
3. IR Receiver Panel
4. Power/Tally Light
5. DialSwitch(Firmware)| 6. 1/4″TripodScrewHole
7. Installation Hole
8. RS-232Control Port(Input)
9. RS-232 Control Port(0utput)
10. HDMI Port| 11. Line in Port
12. 3G-SDI Port
13. USB Port
14. RJ-45 Port
15. DC12V Plug
---|---|---

IR Remote Controller

Power
When powered on, pressing the power key enters standby mode; Pressing it again will start up the camera and display normally.
Freeze (No Function)
The Freeze button has no function on the PTZ.
IRT (IR Transfer/IR Pass)
Enables IR transfer. 0nce pressed, the camera will receive and pass IR remote control signal (via VISCA IN Port).

SET 1~4 Address Setting
Hold the SET# button for 3 seconds to set the cameras IR address.
CAM 1~4 (Camera selecting)
Pressing the CAM# button will enable IR control of the selected camera.

Number Key (1-9)
Set Preset: To set preset, hold down a key (0-9) and wait 3 seconds. 0ncecomplete, the selected preset will be saved.
Run Preset: Pressing a key (0-9)will bring up the corresponding saved preset.
CLR PRE (Clear Preset)
Clear a Preset :Press CLRPRE and key (0-9)simultaneously to remove the corresponding saved preset.
Clear all Presets: Hold down CLRPRE button to remove all saved presets.
Learn
This button is used with other remote buttons. It has no function when pressed alone.

Focus Key (+/-)
Allows for precise focus change. Manual focus mode must be enabled to use these keys.
Zoom Key (+/-)
0ptically zooms the camera in up to 12x.
Navigate Key (Up/Down/Left/Right)
Normal mode: Allows for the camera head to pan and tilt. Menu mode: Allows for direction in the menu of the camera.
OK/Home Key
Normal mode: Recalls to the home position of the camera.
Menu mode: Used to set functions in the menu and activate features.

AF (Auto Focus) When enabled, the camera will automatically focus on the closest object.
MF (Manual Focus) When enabled, the camera will only focus when using one push focusing, or the focus keys on the remote.
Reset Factory resets image properties only.
Menu Used to enter the OSD menu of the camera
Limit L
Press this key with the Learn keytop seethe max left position of the camera.
Limit R
Press this key with the Learn keytop seethe max right position of the camera. LMT CLR Press this key with the Learn keytop remove set max positions.
BLC OFF/BLC ON
Not available.
Bright+/Bright –
These buttons raise or lower the brightness of the image.

Video Format Keys:
While directly pointing at the camera, please hold the desired video output button for 3 seconds. If done properly, the PTZ will do a quick reset to the desired video output selected.

OSD MENU

1. When the camera is on, press the MENU key on the IR remote controller to enter the OSD Menu.

2. After entering the main menu, use the UP/ Down navigate keys on the controller to select the main menu. As you scroll through the menu, the selection will be highlighted in blue.

3. Press the RIGHT navigate key to enter the highlighted sub menu. Use the UP/DOWN navigate keys to select within the sub menu. Use the LEFT/RIGHT navigate keys to enable or disable parameters.

4. To return to the previous menu, you need to press return in the sub menu or MENU on the remote.
   To fully leave the menu, press the MENU key again.

5. OSD Menu Setting List:

PTZF| FOCUS MODE| AUTO/MANUAL: Ability to change from auto or manual focus| DEFAULT: AUTO
---|---|---|---
DIGITAL ZOOM| ON/OFF: Ability to digitally zoom 2X. (PTZ-X12-IP | PTZ-NDI-X12 only)| DEFAULT: OFF
RATIO DISPLAY| ON/OFF: Grants display of the zoom X module. Off by default.| DEFAULT: OFF
ZOOM SPEED| Zoom speed control IR remote: 7 changeable levels.| DEFAULT: 5
SPEED BY ZOOM| When zoomed into the max, the camera will slowly tilt| DEFAULT: ON
PAN/TILT SPEED| Pan/Tilt speed control by IR remote. Controllable at different levels| DEFAULT: 18
RETURN| Return to previous menu.|
EXPOSURE MODE| AUTO/MANUAL/BRIGHT/SHUTTER/IRIS: Choose the current Exp. Mode| DEFAULT: AUTO

EXPOSURE

| SHUTTER| Set shutter speed. 1/30-1/10000: Allows for tuning of the shutter speed| DEFAULT: AUTO
IRIS| Set Iris: CLOSE-F1.8: Allows for tuning of the Iris opening.| DEFAULT: AUTO
GAIN| Set gain: 0dB-28dB: Allows for tuning the gain of the camera| DEFAULT: AUTO
BRIGHTNESS| Set brightness: 0-15: Allows for tuning the brightness of the camera| DEFAULT: AUTO
FLICK| Allows for adjustment of the flicker less options on the camera| DEFAULT: 50Hz
BLACKLIGHT| Allows for the enabling of the backlight or not.| DEFAULT: OFF
GAMMA| Allows setting changes for the Gamma option of the camera| DEFAULT: 0
RETURN| Return to previous menu|
IMAGE| WB MODE| AUTO/INDOOR/OUTDOOR/PUSH/ATW/MANUAL/SODIUM| DEFAULT: ATW
BLUE| Set red gain level: 0-255 (Allows for precise tuning of the blue setting)| DEFAULT: AUTO
RED| Set blue gain level: 0-255 (Allows for precise tuning of the red setting)| DEFAULT: AUTO
DEFOG| Set defog level: This setting allows you to clear up the hazy images| DEFAULT: 0
MIRROR| ON/OFF: Makes the image flip on the vertical plane| DEFAULT: OFF
FLIP| ON/OFF: (optional) Makes the image flip on the horizontal plane| DEFAULT: OFF
COLOR/B&W| COLOR/B&W: Allows for B&W color mode| DEFAULT: COLOR
GAIN LIMIT| Allows you to cap the gain at a certain level| DEFAULT: 15
RETURN| Return to previous menu|
QUALITY| 2DNR| When enabled, image noise and sharpness is reduced| DEFAULT: OFF
---|---|---|---
3DNR| OFF/AUTO/0-4 optional: higher level = less image reduction happens| DEFAULT: AUTO
SHARPNESS| ON/OFF optional, 0-15 level: higher level = sharper edges of image| DEFAULT: 6
CONTRAST| Set contrast level: 0-15: Sets the contrast level| DEFAULT: 8
SATURATION| Set image saturation: 0-15: Sets the saturation level| DEFAULT: 8
BRIGHTNESS| Set brightness of auto exposure: 0-15: Sets the brightness level| DEFAULT: 8
WDR| ON/OFF: Enables better to light and dark images| DEFAULT: OFF
WDR LEVEL| 1-6: Enables more control of WDR| DEFAULT: 1
RETURN| Return to previous menu|
FORMAT| SIZE| 1080p/1080i/720p (default resolution: 1080 30p)| After selecting format, press OK to switch format.
FRAME RATE| 60/59.94/50/30/29.97/25/24/23.98
RETURN| Return to previous menu
SYSTEM| ID| Set VISCA control address 1-7| DEFAULT: 1
BAUDRATE| Set RS-232 baud rate to 2400/4800/9600/115200| DEFAULT: 9600
LANGUAGE/IDIOMA| Set language: ENGLISH/SPANISH| DEFAULT: ENG
DHCP| IP address automatic acquisition switch: ON/OFF| DEFAULT: OFF
IP| Set camera IP| 192.168.1.188
NET MASK| Set camera net mask| 255.255.255.0
GATEWAY| Set camera gateway| 192.168.1.1
RETURN| Return to previous menu|
INFO| IP ADDRESS| Display the current IP address
RTSP URL| Display the current main stream RTSP URL
F/W VERSION| Display the current ISP firmware version
ARM VERSION| Display the current ARM firmware version
FPGA VERSION| Display the current FPGA firmware version
USB VERSION| Display the current USB firmware version
RESET| FACTORY RESET| Reset whole camera to factory parameters
USER SETTING| Save current parameters for User Reset use
USER RESET| Recalls the saved user settings
RETURN| Return to previous menu

Web Settings
The cameras web interface supports Google Chrome, Firefox, IE, Safari, 0pera, and other major browsers.

1. Login
   0pen your browser and in the address bar, type in the camera’s default IP address: 192.168.1.188 (If that doesn’t work please check in the camera’s menu to see the actual IP address under INF0) Next, enter the username and password. The default for both is admin.

2. Real-time Preview
   When logging in, you will see the Realtime preview of the camera.As seen, the control interface is on the right. You can control the camera’s movements with the movement pad at the top, as well as control zoom and focus. You can also set the movement, focus, and zoom speed, as well being able to control your presets.![AIDA PTZ X12 IP Full HD Optical Zoom PTZ

• Safety Guide2](https://manuals.plus/wp-content/uploads/2023/09/AIDA-PTZ-X12 -IP-Full-HD-Optical-Zoom-PTZ-Safety-Guide2.png)

  3. Parameter Settings
     Click “Setting” to enter the parameter setting interface as seen below:

Under “Video Encode”, you can enable the RTSP/RTMP streams for both the main and sub streams. You may also change the Encode mode, choosing betweenH.264orH.265.Lastly, you can change the framerate and bitrate for each stream on this menu.

“RTMP Setting” allows you to directly stream to many social platforms such as YouTube & Facebook Live.
Here you can place the RTMP address, as well as enable the RTMP stream. To do this, you must:
1st: First obtain the live RTMP address (for YouTube, it is rtmp://a.rtmp.youtube.com/live2). You will also need your stream key.
2nd: Place the live RTMP address in the Main RTMP address box.
3rd: Next, ensure that there is a forward slash (/)after the RTMP address. If there is already a forward slash, please skip this step.
4th: Lastly, paste your stream key after the forward slash (/).
5th: Click Save.
0nce you complete these steps, your PTZ will immediately start uploading to your social platforms channel. You will see a blue checkmark next to the RTMP state, which will show if your RTMP address is correctly inputted. No reboot required!
Custom RTMP stream keys also allows you to make your own RTMP address and pull that stream from other programs. If you are stuck on any of these steps, contact our support. They will be glad to assist you in any problems you may encounter.

For NDI versions, you will also see the NDI on and off button here.
In the “audio settings” tab, audio can be turned off or on. You are also able to adjust the encode mode, sample rate, and bitrate.

“Image Parameter” is the online version of the OSD Menu. You can change the same settings via browser. “Ethernet” allows for fine tuning if the IP portion of the camera. You can enable DHCP for auto IP configuration.

To upgrade the firmware on our PTZ, head over to our website at aidaimaging.com/download and look for the latest PTZ firmware.
The “Reset to default” portion allows you to factory reset image parameter reset, or reboot the camera.
Simple Reset: 0nlyresets customizable camera options: AE, WB, Image Effects, etc.
Complete Reset: Factory resets the camera, including the IP address
Reboot: Reboot ISP portion of the camera.

“Account Settings” is used to change the log in for the account. You can change the username and password here.

VISCA over IP

The AIDA PTZ’s use VISCA over IP protocol to reliably send and receive information from IP controllers.
Communication port specs:

• Control port: RJ-45 Gigabit LAN
• IP Protocol:IPv4
• Transmit Protocol: UDP
• IP address: Default 192.168.1.188 (Check OSD Menu)
• Port address:52381
• Confirm send/transmission control: Depends on software

What is VISCA over IP?
VISCA commands are the communication between the controller and the camera. These commands are sent via UDP on the network. Since UDP transmission isn’t that stable, a couple of steps must happen before a movement is  executed. The controller first sends out a VISCA command. The camera equipment then receives the VISCA command and returns that message back to the controller. 0ncethe commands are executed, the action will follow suit and the  message will be complete. Each VISCA command controls its own setting, so there are no overlaps in existing commands.

VISCA IN (RS-232 Port)

VISCA IN & Mini DIN Connection

VISCA IN & DB9 Connection

Serial Port Configuration

VISCA Protocol

Part 1: Camera Return Command

ACK/Completion Message

| Command Packet| Note
ACK| z0 41 FF| Returned when the command is accepted
Completion| z0 51 FF| Returned when the command has been executed

z= camera address +8

Error Messages

| Command Packet| Note
Syntax Error| z0 60 02 FF| Returned when the command format is different or when a command with illegal command parameters is accepted
Command Not Executable| z0 61 41 FF| Returned when the command cannot be executed due to current conditions. For example, when commands controlling the focus manually are received during auto focus.

Part 2: Camera Control Command

(wide)~0x4000(tele))
Direct with speed| 8x 0A 04 47 0t 0p 0q 0r 0s FF| t: spd 0~7 pqrs: Zoom Position (0(wide)`0x4000(tele))
CAM_Zoom| ON| 8x 01 04 06 02 FF|
OFF| 8x 01 04 06 03 FF
Combine Mode| 81 01 04 36 00 FF| Combine with optical zoom control
Separate Mode| 81 01 04 36 01 FF| Separate with optical zoom control
CAM_Zoom| Stop| 81 01 04 06 00 FF| Enable in separate mode
---|---|---|---
Tele(Variable)| 81 01 04 06 2p FF| Enable in separate mode
Wide(Variable)| 81 01 04 06 3p FF| Enable in separate mode
Direct| 81 01 04 46 0p 0q 0r 0s FF| Enable in separate mode
CAM_Focus| Stop| 8x 01 04 08 00 FF|
Far(Standard)| 8x 01 04 08 02 FF
Near(Standard)| 8x 01 04 08 03 FF
Far(Variable)| 81 01 04 08 2p FF| p=0 (Low) to 7 (High)
Near (Variable)| 81 01 04 08 3p FF| p=0 (Low) to 7 (High)
Direct| 8x 01 04 48 0p 0q 0r 0s FF| pars: Focus Position
Auto Focus| 81 01 04 38 02 FF|
Manual Focus| 81 01 04 38 03 FF|
One Push AF| 8x 01 04 18 01 FF|
CAM_ZoomFocus| Direct| 8x 01 04 47 0p 0q 0r 0s 0t 0u 0v 0w FF| pars: Zoom Position (0(wide)~0x4000(tele)) tow: Focus Position
CAM_WB| Auto| 8x 01 04 35 00 FF|
Indoor| 8x 01 04 35 01 FF
Outdoor| 8x 01 04 35 02 FF
One Push| 8x 01 04 35 03 FF
ATW| 8x 01 04 35 04 FF
Manual| 8x 01 04 35 05FF
Sodium lamp| 8x 01 04 35 08 FF
Fluorescent| 8x 01 04 35 09 FF
One Push Trigger| 8x 01 04 10 05 FF
CAM_BGain| Reset| 8x 01 04 03 00 FF| Manual Control of Regain
Up| 8x 01 04 03 02 FF
Down| 8x 01 04 03 03 FF
Direct| 8x 01 04 43 00 00 0p 0q FF| pp.: Regain (0~0xFF)
CAM_BGain| Reset| 8x 01 04 04 00 FF| Manual Control of Bain
Up| 8x 01 04 04 02 FF
Down| 8x 01 04 04 03 FF
Direct| 8x 01 04 44 00 00 0p 0q FF| pp.: Bain (0-0xFF)
CAM_AE| Full Auto| 81 01 04 39 00 FF| Automatic Exposure mode
---|---|---|---
Manual| 81 01 04 39 03 FF| Manual Control mode
Shutter Priority| 81 01 04 39 0A FF| Shutter Priority Automatic Exposure mode
Iris Priority| 81 01 04 39 0B FF| Iris Priority Automatic Exposure mode
Bright| 81 01 04 39 0D FF| Bright Mode (Manual control)
CAM_Shutter| Reset| 8x 01 04 0A 00 FF| Shutter Setting
Up| 8x 01 04 0A 02 FF
Down| 8x 01 04 0A 03 FF
Direct| 8x 01 04 4A 00 00 0p 0q FF| pq: Shutter Position (0~0x15)
CAM_Iris| Reset| 8x 01 04 0B 00 FF| Iris Setting (0~0x0D)
Up| 8x 01 04 0B 02 FF
Down| 8x 01 04 0B 03 FF
Direct| 8x 01 04 4B 00 00 0p 0q FF| pq: Iris Position (0~0x0D)
CAM_BGain| Reset| 8x 01 04 0C 00 FF| Gain Setting (0~0x0E)
Up| 8x 01 04 0C 02 FF
Down| 8x 01 04 0C 03 FF
Direct| 8x 01 04 0C 00 00 0p 0q FF| pq: Gain Position (0~0x0E)
Lambright| Reset| 8x 01 04 0D 00 FF| Bright Setting
Up| 8x 01 04 0D 02 FF
Down| 8x 01 04 0D 03 FF
Direct| 8x 01 04 4D 00 00 0p 0q FF| pp.: Bright Position (0~0x1B)
CAM_ImageBright| Direct| 8x 01 04 A4 00 00 0p 0q FF| pp.: Image Bright Position (0~0x0F) AE_AUTO/AE_SHUTTER/AE_IRIS
CAM_WDR| On| 8x 01 04 3D 02 FF| Exposure Compensation ON/OFF
Off| 8x 01 04 3D 03 FF
Direct| 8x 01 04 D3 pq FF| pq: ExpComp Position (0~0x6)
CAM_Backlight (BLC)| On| 8x 01 04 33 02 FF| Backlight On
Off| 8x 01 04 33 03 FF| Backlight Off
CAM_Sharpness| Reset| 8x 01 04 02 00 FF| Aperture Control
Up| 8x 01 04 02 02 FF
Down| 8x 01 04 02 03 FF
Direct| 8x 01 04 42 00 00 0p 0q FF| pq: Aperture Gain (0~0x0F)
CAM_Memory (preset)| Reset| 8x 01 04 3F 00 0p FF| p: Preset Number (=0 to 128)

Corresponds to 0-9 on the remote controller

---|---|---|---
Set| 8x 01 04 3F 01 0p FF
Recall| 8x 01 04 3F 02 0p FF
CAM_LR_Reverse| On| 8x 01 04 61 02 FF| Image Flip Horizontal On/Off
Off| 8x 01 04 61 03 FF
CAM_PictureFlip| On| 8x 01 04 66 02 FF| Image Flip Horizontal On/Off
Off| 8x 01 04 66 03 FF
CAM_RS485Ctl| On| 8x 01 06 A5 02 FF|
Off| 8x 01 06 A5 03 FF
CAM_Saturation| Saturation| 8x 01 04 A1 00 00 0p 0q FF| pq: Saturation Level 0x00~0xff
CAM_Contrast| Contrast| 8x 01 04 A2 00 00 0p 0q FF| pq: Contrast Level 0x00~0xff
CAM_SpeedByZoom| On| 8x 01 06 A0 02 FF|
Off| 8x 01 06 A0 03 FF
CAM_PTSpeed| PT Speed| 8x 01 04 C1 00 00 0p 0q FF| pq: PT Speed 0x05~0x18
CAM_ZoomSpeed| Zoom Speed| 8x 01 04 D1 00 00 0p 0q FF| pq: Zoom Speed 0x01~0x07
CAM_ZoomDisplay| On| 8x 01 06 C2 02 FF|
Off| 8x 01 06 C2 03 FF
CAM_IRaddress| IR address| 8x 01 06 D8 0p FF| p: IR address1~4
CAM_GammaInq| Gamma set| 81 01 04 5B 0p FF| p: Gamma No. (0~4)
CAM_ColorGain| Direct| 8x 01 04 49 00 00 00 0p FF| (0~0x0E)
CAM_2DNR| Direct| 8x 01 04 A5 0p FF| (0~0x1)
CAM_3DNR| Direct| 8x 01 04 53 0p FF| (0~0x05)
FLICK| 50Hz| 81 01 04 23 01 FF|
60Hz| 81 01 04 23 02 FF
OFF| 81 01 04 23 00 FF
VideoSystem Set (AIDA)| | 8x 01 06 35 00 pp FF| pp: Video Format:

1080P60                           0x00

1080P50                           0x01

1080I60                            0x02

1080I50                            0x03

1080P30                           0x 04

1080P25                           0x05

720P60                             0x 06

720P50                             0x07

720P30                             0x08

720P25                             0x09

1080P5994                       0x0E

1080I5994                        0x0F

1080P2997                       0x10

720P5994                         0x13

720P2997                         0x14

1080P24                           0x11

1080P2398                       0x12

---|---|---|---
VideoSystem Set (Sony)| | 81 01 04 24 72 0p 0q FF| pp: Video Format:

1080P60                           0x2e

1080P50                           0x2f

1080I60                            0x01

1080I50                            0x04

1080P30                           0x06

1080P25                           0x08

720P60                             0x09

720P50                             0x0c

720P30                             0x0e

720P25                             0x11

1080P5994                       0x13

1080I5994                        0x02

1080P2997                       0x07

720P5994                         0x0a

720P2997                         0x0f

1080P24                           0x2a

1080P2398                       0x2b

CAM_IDWrite| | 8x 01 04 22 0p 0q 0r 0s FF| pqrs: Camera ID (=0000 to FFFF)
DHCP control| DHCP off| 8x 01 04 AE 00 FF| DHCP off
DHCP on| 8x 01 04 AE 01 FF| DHCP on
Main Stream| Resolution| 8x 01 04 C2 00 0p 0q 0r 0s 0m 0n 0x 0y FF| pqrs: Column(x size) myxy: Line (y size) only support: 1920×1080/1280×720
Rate| 8x 01 04 C2 01 0p 0q 0r 0s 0m 0n 0x 0y FF| pqrsmnxy: bitrate (0~15360)
Sub Stream| Resolution| 8x 01 04 C3 00 0p 0q 0r 0s 0m 0n 0x 0y FF| pqrs : Column(x size) myxy: Line (y size) only support: 1280×720/1024×576/640×360
Rate| 8x 01 04 C3 01 0p 0q 0r 0s 0m 0n 0x 0y FF| pqrsmnxy: bitrate (0~15360)
Tally Control| Off| 8x 01 7E 01 0A 00 0p FF| p: 0: OFF(LED off) 1: (LED green on) 2: (LED red on) 4: (LED blue on)
IP address control| IP Set| 8x 01 04 AB 0p 0q 0r 0s 0m 0n 0x 0y FF| Set ip to :pq.rs.mn.xy
Mask| 8x 01 04 AC 0p 0q 0r 0s 0m 0n 0x 0y FF| Set mask to :pq.rs.mn.xy
Gateway set| 8x 01 04 AD 0p 0q 0r 0s 0m 0n 0x 0y FF| Set gateway to :pq.rs.mn.xy
Color adjust| Color Adjust OFF| 8x 01 04 B6 00 FF| Color adjust off
Color Adjust ON| 8x 01 04 B6 01 FF| Color adjust on
Brightness Balance OFF| 8x 01 04 B7 00 FF| Keep Brightness
Brightness Balance ON| 8x 01 04 B7 01 FF| Don’t Keep Brightness
Color adjust| Flare red| 8x 01 04 B8 dat FF| Flare mode red value (Default=32)
---|---|---|---
Flare green| 8x 01 04 B9 dat FF| Flare mode green value (Default=32)
Flare blue| 8x 01 04 BA dat FF| Flare mode blue value (Default=32)
SYS_Menu| Menu On| 8x 01 06 06 02 FF| Turn on menu
Menu Off| 8x 01 06 06 03 FF| Turn off menu
Menu Back| 8x 01 06 06 10 FF| Menu step back
Menu Ok| 8x 01 7E 01 02 00 01 FF| Menu ok
IR_Receive| On| 8x 01 06 08 02 FF| IR(remote commander)receive ON/OFF
Off| 8x 01 06 08 03 FF
On/Off| 8x 01 06 08 10 FF
Pan_TiltDrive| Up| 8x 01 06 01 VV WW 03 01 FF| VV: Pan speed 0x01 (low speed) to 0x18 (high speed)

WW: Tilt speed 0x01 (low speed) to 0x14 (high speed)

YYYY: Pan Position(TBD) ZZZZ: Tilt Position(TBD)

Down| 8x 01 06 01 VV WW 03 02 FF
Left| 8x 01 06 01 VV WW 01 03 FF
Right| 8x 01 06 01 VV WW 02 03 FF
Uplift| 8x 01 06 01 VV WW 01 01 FF
Upright| 8x 01 06 01 VV WW 02 01 FF
Downlit| 8x 01 06 01 VV WW 01 02 FF
Downright| 8x 01 06 01 VV WW 02 02 FF
Stop| 8x 01 06 01 VV WW 03 03 FF
Absolute Position| 8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
Relative Position| 8x 01 06 03 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
Home| 8x 01 06 04 FF
Reset| 8x 01 06 05 FF
Pan Tilt_LimitSet| Set| 8x 01 06 07 00 0W 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF| PW: 1: UpRight 0:DownLeft YYYY: Pan Limit Position(TBD) ZZZZ: Tilt Limit Position(TBD)
Clear| 8x 01 06 07 01 0W 07 0F 0F 0F 07 0F 0F 0F FF

Part 3: Inquiry Command

Position
CAM_WBModeInq| 8x 09 04 35 FF| y0 50 00 FF| Auto
y0 50 01 FF| Indoor Mode
y0 50 02 FF| Outdoor Mode
y0 50 03 FF| One-use Mode
y0 50 04 FF| ATW
y0 50 05 FF| Manual
CAM_RGainInq| 8x 09 04 43 FF| y0 50 00 00 0p 0q FF| pq: R Grain
CAM_RGainInq| 8x 09 04 44 FF| y0 50 00 00 0p 0q FF| pq: B Grain
CAM_AEModeInq| 8x 09 04 39 FF| y0 50 00 FF| Full Auto
y0 50 03 FF| Manual
y0 50 0A FF| Shutter Priority
y0 50 0B FF| Iris Priority
y0 50 0D FF| Bright
CAM_Shutter Posen| 8x 09 04 4A FF| y0 50 00 00 0p 0q FF| pq: Shutter Position
CAM_IrisPosInq| 8x 09 04 4B FF| y0 50 00 00 0p 0q FF| pq: Iris Position
CAM_GainPosiInq| 8x 09 04 4C FF| y0 50 00 00 0p 0q FF| pq: Gain Position
CAM BrightPosiInq| 8x 09 04 4D FF| y0 50 00 00 0p 0q FF| pq: Bright Position
CAM Image Bright Posing| 8x 09 04 A4 FF| y0 50 00 00 0p 0q FF| pq: ImageBright Position
CAM_SaturationInq| 8x 09 04 A1 FF| y0 50 00 00 0p 0q FF| pq: Saturation level 0x00~0x0f
CAM_DefogInq| 8x 09 04 A3 FF| y0 50 0p FF| p: Defog level 0x00~0x0f
CAM_ContrastInq| 8x 09 04 A2 FF| y0 50 00 00 0p 0q FF| pq: Contrast level 0x00~0x0f
CAM_WDRModeInq| 8x 09 04 3D FF| y0 50 02 FF| On
y0 50 03 FF| Off
CAM_WDRPosInq| 8x 09 04 2D FF| 8x 01 04 02 03 FF| pq: WDR LEVEL Position 1~6
CAM_ApertureInq| 8x 09 04 42 FF| y0 50 00 00 0p 0q FF| p: Aperture Gain
---|---|---|---
CAM_FlickerInq| 8x 09 04 AA FF| y0 50 0p FF| p: Flick mode 0:off 1:50Hz 2:60Hz
CAM_2DNRInq| 8x 09 04 A5 FF| y0 50 0p FF| p: 2DNR: 0=OFF 1= AUTO 2
CAM_3DNRInq| 8x 09 04 53 FF| y0 50 0p FF| p: 3DNR: 0=OFF 1= AUTO 2~5=Manual Level
CAM_GammaInq| 8x 09 04 5B FF| y0 50 0p FF| p: Gamma Position
CAM_MemoryInq| 8x 09 04 3F FF| y0 50 pp FF| pp: Memory number last operated
SYS_MenuModeInq| 8x 09 06 06 FF| y0 50 02 FF| On
| | y0 50 03 FF| Off
CAM_LR_Reverse IN| 8x 09 04 61 FF| y0 50 02 FF| On
| | y0 50 03 FF| Off
CAM_PictureFlipInq| 8x 09 04 66 FF| y0 50 02 FF| On
| | y0 50 03 FF| Off
CAM_IDInq| 8x 09 04 22 FF| y0 50 0p 0q 0r 0s FF| pqrs: Camera ID
CAM_DHCPInq| 8x 09 04 AE FF| y0 50 pp FF|
CAM_IDInq| 8x 09 04 AB FF| y0 50 0p 0p 0q 0q 0r 0r 0s 0s FF
CAM_MASKInq| 8x 09 04 AC FF| y0 50 0p 0p 0q 0q 0r 0r 0s 0s FF
CAM_GATEWAYInq| 8x 09 04 AD FF| y0 50 0p 0p 0q 0q 0r 0r 0s 0s FF
CAM_FlareModeInq| 8x 09 04 B6 FF| y0 50 pp FF
CAM_FlareBright Modeling| 8x 09 04 B7 FF| y0 50 pp FF
CAM_FlareRed| 8x 09 04 B8 FF| y0 50 pp FF
CAM_FlareRed| 8x 09 04 B9 FF| y0 50 pp FF
CAM_FlareBlue| 8x 09 04 BA FF| y0 50 pp FF
CAM_VersionInq| 8x 09 00 02 FF| y0 50 ab cd MN pq rest to vow FF
VideoSystemInq (AIDA)| 8x 09 06 23 FF| y0 50 pp FF| pp: Video position
VideoSystemInq (Sony)| 8x 09 04 24 72 FF| y0 50 0p 0p FF| pp: Video position
Retransfer| 8x 09 06 1A FF| y0 50 02 FF| On
y0 50 03 FF| Off
Tallying| 8x 09 7E 01 0A FF| y0 50 0p FF| p: tally state
IR_Receive| 8x 09 06 08 FF| y0 50 02 FF| On
y0 50 03 FF| Off
IR_ReceiveReturn| | y0 07 7D 01 04 00 FF| Power ON/OFF
IR_ReceiveReturn| | y0 07 7D 01 04 00 FF| Zoom tele/wide
---|---|---|---
y0 07 7D 01 04 07 FF| AF On/Off
y0 07 7D 01 04 33 FF| CAM_Backlight
y0 07 7D 01 04 3F FF| CAM_Memory
y0 07 7D 01 06 01 FF| Pan_TiltDrive
Pan-tiltMaxSpeed Inq| 8x 09 06 11 FF| y0 50 ww zz FF| ww: PanMaxSpeed zz: Tilt Max Speed
Pan-tiltPosInq| 8x 09 06 12 FF| y0 50 0w 0w 0w 0w 0z 0z 0z 0z FF| wwww: Pan Position zzzz: Tilt Position
Mainstream ResolutionInq| 8x 09 04 C2 00 FF| y0 50 0p 0q 0r 0s 0m 0n 0x 0y FF| pqrs : Column(x size) mnxy: Line (y size) only supports: 1920×1080
Mainstream Rate Inq| 8x 09 04 C2 01 FF| y0 50 0p 0q 0r 0s 0m 0n 0x 0y FF| pqrsmnxy: bitrate (0~15360)
Sub stream ResolutionInq| 8x 09 04 C3 00 FF| y0 50 0p 0q 0r 0s 0m 0n 0x 0y FF| pqrs : Column(x size) myxy: Line (y size) only supports: 1280×720/1024×576/640×360
SubstreamRateInq| 8x 09 04 C3 01 FF| y0 50 0p 0q 0r 0s 0m 0n 0x 0y FF| pqrsmnxy: bitrate (0~15360)

Note: [x] refers to camera address; [y] = [x +8] VISCA Pan Tilt Absolute Position Value

VISCA Pan Tilt Speed Value

Pan Degree/Second

0| 0.3| 0.3| 0.03
1| 1| 1| 1
2| 1.5| 1.5| 1.5
3| 2.2| 2.2| 2.2
4| 2.4| 2.4| 3.6
5| 2.6| 2.6| 4.7
6| 2.8| 2.8| 6
7| 3| 3| 8
8| 3.2| 3.2| 10
9| 3.4| 3.4| 12
10| 3.8| 3.8| 15
11| 4.5| 4.5| 18
12| 6| 6| 23
13| 9| 13| 30
14| 15| 14| 39
15| 19| 15| 48
16| 25| 16| 59
17| 32| 17| 69
18| 38| 18| 80
19| 45| |
20| 58| |
21| 75| |
22| 88| |
23| 105| |
24| 120| |

UVC Control
AIDA PTZ’s also support UVC interface.

Warranty
AIDA Imaging warrants its cameras and items to be free from defects under normal use. Please refer to our website for more information at: aidaimaging.com/support
Support
If you would like additional support or explanation of anything on this manual, please feel free to go to our FAQ page on our website at aidaimaging.com/support. If you are in need of additional help, or have any general questions,  please feel free to contact us in these various ways: Telephone: 909.333.7421
Email: Support@aidaimaging.com
Website: aidaimaging.com/support
We are open yearly, Mon-Fri 8A.M. to 5P.M. PST, excluding major holidays and events.
Also, keep up to date with firmware’s and new releases from AIDA Imaging by signing up for our newsletter!

IMAGING

Documents / Resources

| AIDA PTZ-X12-IP Full-HD Optical Zoom PTZ [pdf] User Manual
PTZ-X12-IP, PTZ-NDI-X12, PTZ-X20-IP, PTZ-NDI-X20, PTZ-X12-IP Full-HD Optical Zoom PTZ, Full-HD Optical Zoom PTZ, Optical Zoom PTZ, Zoom PTZ, PTZ
---|---

References

• Download - AIDA Imaging
• Support Center - AIDA Imaging
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>