AIDA UHD6G-200 UHD 6G-SDI POV Camera User Guide

AIDA UHD6G-200 UHD 6G-SDI POV Camera

Product Information

The UHD 6G-SDI POV Camera (Model: UHD6G-200) is a high-definition camera designed for professional use. It features a 6G-SDI interface, allowing for ultra-high-definition video transmission. The camera is equipped with various features andcontrols, including OSD menu, WB control, AE control, day/night mode, audio settings, image control, special setup options, and reset function.

Product Usage Instructions

1. Ensure to use only the standard adapter specified in the specification sheet. Using any other adapter may result in fire, electrical shock, or damage to the product.

2. When connecting the power supply or replacing the battery, make sure to do so correctly to prevent explosion, excessive heat, or fire.

3. Securely plug the power cord into the power receptacle to avoid any fire hazards.

4. Avoid placing conductive objects or containers filled with water on top of the camera to prevent personal injury from fire, electric shock, or falling objects.

5. Do not install the camera in humid, dusty, or sooty locationsas it may cause fire or electric shock.

6. If you detect any unusual smells or smoke coming from the camera, immediately stop using the product and disconnect the power source. Contact the service center for assistance to prevent fire or electric shock.

7. In case of any operational issues, contact the nearest service center. Do not disassemble or modify the product.

8. When cleaning the camera, avoid spraying water directly onto its parts as it may cause fire or electric shock.
   Please read the provided Operation Guide thoroughly before installing and using the camera. Keep a copy of the guide for future reference.
   Additional usage instructions:

9. Always follow the instructions in the operations guide when applying power to the camera to prevent fire or equipment damage. Refer to the specifications page for the correct power supply.

10. If you notice fumes, smoke, or a strange odor emitted from the camera, or if it does not function correctly, immediately disconnect the power source and consult with your supplier.

11. Avoid installing the camera close to a TV, radio transmitter, magnet, electric motor transformer, or audio speakers, as the generated magnetic field may interfere with or distort the image.

12. Avoid fluorescent light reflections, unstable light conditions, direct sunlight exposure, spotlights, and other bright lights or light reflecting objects when operating the camera.

13. To prevent damage, avoid dropping the camera or subjecting it to strong shock or vibration.

CAUTION:
RISK OF ELECTRIC SHOCK. DO NOT OPEN

CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

WARNING
This symbol indicates that dangerous voltage consisting of a risk of electric shock is present within this unit.

PRECAUTION
This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

To prevent damage that may result in fire or electric shock hazards, do not expose this appliance to rain or moisture.

1. Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing the battery may cause an explosion, cause excessive heat or fire
3. Securely plug the power cord into the power receptacle. The insecure connection may cause a fire.
4. Do not place conductive objects (e.g. screwdrivers, coins, metal items, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects
5. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock
6. If any unusual smells or smoke come from the unit, stop using the product. Immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.
7. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way.
8. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

PRECAUTION

Please read this Operation Guide before installing and using the camera & retain this copy for your reference.

1. Always follow the instructions in the operations guide when applying power. Fire and equipment damage can occur if power is applied incorrectly. For the correct power supply,refer to the specifications page.
2. Do not use camera if fumes, smoke or a strange odor is emitted from the camera, or if it seems not functional correctly. Disconnect the power source immediately and consult with your supplier.
3. Do not use the camera in extreme environments where high temperatures or high humidity exists. Use the camera under conditions where temperatures are between 32°F ~ 104°F, and humidity is below 90%.
4. If installed close to a TV, radio transmitter, magnet, electric motor transformer or audio speakers the magnetic field generated may interfere with or distort the image.
5. Try to avoid fluorescent light reflections, unstable light conditions, direct pointing toward the sun. Use caution when operating the camera in the vicinity of spotlights or other bright lights and light reflecting objects.
6. To prevent damage, do not drop the camera or subject it to strong shock or vibration

OVERVIEW

FEATURES

• 4K UHD 1/2.5 Progressive Scan CMOS sensor captures sharp and vivid UHD video even under low light conditions.
• Advanced digital imaging processor provides vivid and detailed images by utilizing Dynamic Range, Auto White Balance, and Noise Reduction.
• Superb motion-compensated temporal noise reduction filter for motion video without blurring.
• OSD control breakout cable with power input and RS-485 for remote communication.
• Flawlessly relays multi-channel embedded audio via SDI output.
• Interchangeable lens design compatible with CS and C mount lenses.
• Perfectly suited for broadcast, pro audio/video, and security.
• Conforming with SMPTE 292M, 424M, and 2081-10.
• Versatile, compact, and rugged design.

**OSD MENU

**

1. Move the Cursor Up/Down to Choose Menu
   To move from item to item in the menu, move the joystick to the Up/Down.

2. Change the Value
   To change the value of the selected item, move the joystick to the Left/Right.

3. Shift to the Sub Menu of the Chosen Menu
   To go into sub menu, press SEL key. The menu items with > always have its sub menu.

EXPOSURE

AUTO

Auto mode will adjust the exposure level automatically.
Detailed fine tuning options are available under this menu.

• AGC MAX : OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX
  “AGC MAX” sets the maximum gain value to control the video noise caused by Auto Gain Control.

• SENS UP : OFF, x2 ~ x10
  “SENS UP” mode controls the digital slow shutter to allow extra light into the camera and adjust the picture quality.

• AE BRIGHT : 0~20
  Auto Exposure brightness level can be adjusted.

SHUT FIX
SHUT FIX mode provides more detailed shutter speed option.
All other controls are tuned for the selected shutter speed.

• SHUTTER : AUTO, 1/30 ~ 1/10,000 ( Shutter speed can be set )

• AGC MAX : OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX
  “AGC MAX” sets the maximum gain value to control the video noise caused by Auto Gain Control.

• SENS UP : 0~20
  “SENS UP” mode controls the digital slow shutter to allow extra light into the camera and adjust the picture quality.

• AE BRIGHT : 0~10
  Auto Exposure brightness level can be adjusted

AGC FIX
AGC FIX mode provides more detailed gain option.
All other controls are tuned for the selected gain value.

• AGC : AUTO, 0dB ~ 27dB, d2X ~ d9X
  Gain level can be set.

• AGC MAX : OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX
  “AGC MAX” sets the maximum gain value to control the video noise caused by Auto Gain Control.

• AE BRIGHT : 0~10
  Auto Exposure brightness level can be adjusted.

• IRIS SPEED : 0 ~ 5
  Electronic Iris speed can be controlled. ( DC Iris lens only )

• LENS MODE : INDOOR, OUTDOOR, MANUAL
  Lens setting will be optimized for the selected environment. ( DC Iris lens only )

• FLK CONTROL : AUTO, ON, OFF
  “FLK CONTROL” mode provides a proper image sensor frequency to match the power frequency in order to minimize video flicker.

WHITE BALANCE

ATW
Auto trace white mode will adjust white balance within 1,900˜K ~ 11,000˜K temperature.

• SPEED : 0 ~ 7
  White balance adjust speed can adjusted.

• OFFSET-B : 0 ~ 100
  “OFFSET-B” adjusts Blue gain within the range of 0 to 100.

• OFFSET-R : 0 ~ 100
  “OFFSET-R” adjusts Red gain within the range of 0 to 100.

ONE PUSH
One push mode is used if AWB or ATW cannot produce the proper white balance.
Place a white paper in front of the camera when using the one push mode to self adapt.

PUSH
Press Select button to enable “ONE PUSH” white balance adjustment. Place a white paper in front of the camera when using the “ONE PUSH” mode to self- adopt.

Camera provides a wide range of white balance options.
Check your color temperature before adjusting this mode.

INDOOR
“INDOOR” mode will adjust white balance to indoor lighting conditions.

OUTDOOR
“OUTDOOR” mode will adjust white balance to outdoor lighting conditions.

MANUAL
“MANUAL” mode will adjust white balance manually.

• BLUE – 0 ~ 100
  Select blue gain within the range of 0 to 100.

• RED – 0 ~ 100
  Select Red gain within the range of 0 to 100.

DAY & NIGHT

Adjust color or B&W setting from this menu.

• MODE : DAY(COLOR), NIGHT(B&W)
  Set camera to either color mode or B&W mode.

• NIGHT COLOR : ON, OFF
  When “NIGHT COLOR” is turned ON, camera stays on color mode even
  “NIGHT(B&W)” is selected from the MODE.

• COLOR BURST : ON, OFF
  Color burst signal ON or OFF can be set for CVBS signal. ( Not applicable )

DNR

NOISE REDUCTION
Camera noise level can be adjusted from this menu

• DNR MODE : OFF, 2D, 3D, 2D+3D
  Digital noise reduction can be applied from this menu.

• DNR LEVEL : AUTO, LOW, MIDDLE, HIGH
  Noise reduction level can be adjusted from this menu.

• DNR APERTURE : 0 ~ 4
  Motion artifacts tightness can be adjusted.
  0 = Most ghost artifact 4 = Least ghost artifact

PRIVACY

Privacy zone can be setup from this menu.

• MODE : ON, OFF
• Enable “PRIVACY ZONE” ON or OFF.
• TYPE : SQUARE, POLYGON
• Select privacy zone shape.
• MASK NO : MASK1 ~ MASK8
• Select privacy zone mask number.
• DISPLAY : ON, OFF
• Turn ON or OFF the selected privacy mask zone.
• COLOR : WHITE, GREEN, BLUE, RED, CYAN, MAGENTA, YELLOW, GRAY-1 ~ 6,
• MOSAIC, BLACK. ( Select privacy zone mask color )
• POLY SELECT : L- TOPP, L- BOTTOM, R- TOP, R-BOTTOM
• Change the shape of the polygon by selecting the corner of the polygon.
• POSITION-X & POSITION-Y
• Change the size of the selected corner from “POLY SELECT” menu.
• SIZE-X & SIZE-Y
• Change the size of the privacy square.
• DEFAULT
• Set privacy zone to default value

EFFECT

Camera image control can be adjusted from EFFECT menu.

• LENS SHADING : ON, OFF
  Optical vignetting issue can be corrected from this menu.

• GAMMA CORRECT : ON, OFF (1.0)
  Gamma level can be adjusted.

• Y LUT EXTEND : UNIFORM, EXTEND-F2C
  Tuning and engineering purpose LUT correction.

• BYLUT XSAMPLE : 64x256LUT, 32x256LUT, 64x256LUT, 128x256LUT, 256x256LUT
  Tuning and engineering purpose LUT correction.

• RGBLUT XSAMPLE: 64x256LUT, 32x256LUT, 64x256LUT, 128x256LUT, 256x256LUT
  Tuning and engineering purpose LUT correction.

• CONTRAST : 0 ~ 20 ( Contrast level can be adjusted )

• BRIGHTNESS : 0 ~ 20 ( Brightness level can be adjusted )

• SATURATION : 0 ~ 20 ( Saturation level can be adjusted )

• HUE : 0 ~ 20 ( Hue level can be adjusted )

• EDGE ENHANCE : 0 ~ 20 ( Image sharpness level can be adjusted )

• AUTO SATURATE : OFF, LOW, MIDDLE, HIGH
  Decrease saturation automatically when noisy scene is detected.

• AUTO EDGE : ON, OFF
  Decrease edge enhancement (sharpness) automatically when noisy scene is detected.

• DEFAULT : See Effects menu to default value.

SPECIAL

Camera special functions can be adjusted from SPECIAL menu.
D ZOOM : ON, OFF ( Digital Zoom and PIP function can be enabled from this menu )

• ZOOM CONTROL : RATIO, POSITION, RETURN
  Adjust the digital zoom ratio and position.

• Use LEFT / RIGHT button to adjust the ratio, then press select.

• USE LEFT / RIGHT/ UP / DOWN button to adjust the image position, then press select. Press select to exit.

• PIP : ON, OFF ( Turn ON or OFF the PIP window )

• PIP SIZE : 1/16, 1/25 ( Change the size of PIP window )

• PIP POSITION : POSITION, RETURN ( Adjust the PIP window location )

• USE LEFT / RIGHT/ UP / DOWN button to adjust the image position,then press select. Press select to exit.

• DEFAULT : Set privacy zone to default value

SPECIAL

DEFOG: ON, OFF, AUTO
The “DEFOG” menu improves foggy image.

• STRENGTH : 0 ~ 16
  Change defog strength.

• THRESHOLD : 0 ~ 3
  The threshold value sets the minimum sensitivity value for automatic defog control.
  Higher value makes defog-on control reluctant.

• AUTO LEVEL: LOW, MID, HIGH
  Auto level value sets maximum strength value for automatic defog control.
  A higher value makes defog effect to be stronger.

DIS: Digital image stabilization can be turned ON or OFF.
BACK-LIGHT: OFF, BLC, HLM – Camera back-light compensation can be adjusted.
BLC: OFF, ON – BLC enables backlight compensation.

• SIZE/POSITION: SIZE, POSITION, RETURN
  Adjust BLC area window size.

• DISPLAY: OFF, ON
  BLC area display can be turned ON or OFF

• DEFAULT: Set BLC menu to default value.

HLM: OFF, ON
HLM can be adjusted.

• AREA DISPLAY: ON, OFF
  HLM AREA DISPLAY can be turned ON or OFF.

• SIZE/POSITION: SIZE, POSITION, RETURN
  Adjust BLC area window size.

• LEVEL : 0 ~ 20
  The amount of masking area can be adjusted.

• BLACK MASK: OFF, ON
  The masking area highlight can be turned ON or OFF.

• DEFAULT: Set HLM menu to default value

• BINNING: OFF, ON
  Binning can be turned ON or OFF.

• DEFECT PIXEL: OFF, ON, ON (FIXED), STATIC
  The defective Pixel Correction feature can be operated. It is turned ON by default and will run both dynamic and static DPC functions.

DISPLAY FUNCTION : OFF, ON
Adjust image display features from this menu.

• FREEZE : OFF, ON
  Image freeze can be turned ON or OFF.

• MIRROR : OFF, MIRROR, V-FLIP, BOTH(H/V) Image mirror or flip can be operated.

• IMAGE EFFECT : OFF, NEGATIVE, GREY MODE, REDDISH-1 ~ 4,
  BLUISH-1 ~ 4, GREENISH-1 ~ 4.ROTATION : OFF, ROT_L 1:1
  Several color effects can be applied.

• ROTATION : OFF, ROT_L FULL, ROT_L 1:1, ROT_R Full, ROT_R 1:1
  Image can be rotated either left or right side.

• PICTURE STYLE : OFF, STANDARD, VIVID, CLEAR, VIVID CLEAR, NEUTRAL
  Different types of picture style can be applied.

• FLICKER DETECT : OFF, ON
  “FLICKER DETECT” mode provides a proper image sensor frequency to match the power frequency in order to minimize video flicker

SETUP

• Camera setup can be adjusted from this menu.
  CAM TITLE : OFF, ON
  Camera title can be turned ON or OFF.

• RS-485 :
  VISCA communication control can be adjusted.

• CAM ID : 0 ~ 7
  Camera ID can be setup.

• ID DISPLAY : OFF, ON
  Camera ID can be setup.

• BAUDRATE : 2400, 4800, 9600, 19200, 38400
  Camera baudrate can be set.

• SYSTEM INFO : ON, OFF, AUTO
  Camera information can be found under this menu.

• OUTPUT FORMAT : ON, OFF, AUTO
  Camera resolution and frame rate can be set

• MENU COLOR :
  OSD menu color can be adjusted.

AUDIO
Audio input [MIC or LINE] can be selected, and level can be adjusted under this menu.

SPECIFICATION

VIDEO

• Image Sensor 1/1.7” Progressive CMOS
• Sensor Size Diagonal 9.93mm(17:9)
• Effective Pixels Horizontal: 4096, Vertical: 2160
• Pixel Size 1.85 μm x 1.85 μm
• Resolution 4096 x 2160, 3840 x 2160, 1920 x 1080, 1280 x 720
• Resolution Rate 4K (4096 X 2160) 60/59.94/50/30/29.97/25/24 3840p 60/59.94/50/30/29.97/25/24p 1080p 60/59.94/50/30/29.97/25p/24p 1080i 60/59.94/50i 720 60/59.94/50p
• Output HDMI 2.0
• Color Space 4:2:2 (YCbCr) 10bit

LENS

• Lens C/CS Mount (with 4K 3.6mm – 11mm varifocal lens)

AUDIO INPUT

• Input 3.5mm TRS Stereo
• Mic-in & Line in over I/O Cable
• Sample Rate 16/24/32 Bits

STANDARD

• SMPTE SMPTE 292M, SMPTE 424M

PHYSICAL

• Camera Control RS-485 VISCA, OSD Button
• Operation Temp 15° F – 120° F
• Dimension 51mm x 51m x 102mm / 2.01” x 2.01” x 4.01”
• Weight 384g / 0.84lbs
• Power 12VDC (+9 – +15VDC)

Specification are subject to change without notice.

QUESTIONS

Visit us:
www.aidaimaging.com/support
E-mail us:
[email protected]
Give us a Call:
Toll Free : 844.631.8367 | Tel: 909.333.7421
Operating Hours : Mon-Fri | 8:00am – 5:00pm PST

Disposal of Old Appliances

• When this crossed-out wheel bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.
• All electrical and electronic products should be disposed of separately form the municipal waste stream in accordance to laws designated by the government or the local authorities.
• The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.
• For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful inter reference in which case the user will be required to correct the interference at his own expense.
Reproduction of this manual, in whole or in part, by any means, is prohibited

References

• Support Center - AIDA Imaging

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>