AIDA UHD-200 4K 60p POV Camera User Guide
- June 6, 2024
- AIDA
Table of Contents
4K 60p POV Camera
UHD-200
OPERATION GUIDE
Version 1.0 / April 2020
Reproduction of this manual, in whole or in part, by any means, is
prohibited.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING
This symbol indicates that dangerous voltage consisting a risk of electric
shock is present within this unit.
PRECAUTION
This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING
To prevent damage that may result in fire or electric shock hazards, do not expose this appliance to rain or moisture.
- Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product.
- Incorrectly connecting the power supply or replacing the battery may cause an explosion, cause excessive heat, or fire
- Securely plug the power cord into the power receptacle. The insecure connection may cause fire.
- Do not place conductive objects (e.g. screwdrivers, coins, metal items, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
- Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock
- If any unusual smells or smoke come from the unit, stop using the product. Immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.
- If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way.
- When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
PRECAUTION
Please read this Operation Guide before installing and using the camera & retain this copy for your reference.
- Always follow the instructions in the operations guide when applying power. Fire and equipment damage can occur if power is applied incorrectly. For the correct power supply, refer to the specifications page.
- Do not use camera if fumes, smoke or a strange odor is emitted from the camera, or if it seems not functional correctly. Disconnect the power source immediately and consult with your supplier.
- Do not use the camera in extreme environments where high temperatures or high humidity exists. Use the camera under conditions where temperatures are between 32°F ~ 104°F, and humidity is below 90%.
- If installed close to a TV, radio transmitter, magnet, electric motor transformer or audio speakers the magnetic field generated may interfere with or distort the image.
- Try to avoid fluorescent light reflections, unstable light conditions, direct pointing toward the sun. Use caution when operating the camera in the vicinity of spotlights or other bright lights and light reflecting objects.
- To prevent damage, do not drop the camera or subject it to strong shock or vibration.
UHD-200
FEATURES
- 4K UHD 1/1.7” Progressive Scan CMOS sensor capable of 4K (4096 x 2160) captures sharp and vivid images even under very low light conditions.
- Powered by a back-illuminated pixel technology.
- Advanced digital imaging processor provides vivid and detailed images by utilizing Dynamic Range, Auto White Balance, and Noise Reduction.
- Superb motion-compensated temporal noise reduction filter for motion video without blurring.
- OSD control breakout cable with two audio inputs and RS-485 for remote communication.
- Flawlessly relays multi-channel embedded audio via HDMI 2.0.
- Perfectly suited for broadcast, pro audio/video, and security.
- Versatile, compact, and rugged design.
OSD MENU
-
Move the Cursor Up/Down to Choose Menu
To move from item to item in the menu, move the joystick to the Up/Down. -
Change the Value
To change the value of the selected item, move the joystick to the Left/Right. -
Shift to the Sub Menu of the Chosen Menu
To go into sub menu, press SEL key. The menu items with > always have its sub menu.
WB CONTROL
AWB – Auto white balance mode will adjust white balance within 3,000˜K ~
8,000˜K temperature.
ATW – Auto trace white mode will adjust white balance within 1,900˜K ~
11,000˜K temperature.
ONE PUSH – One push mode is used if AWB or ATW cannot produce the proper
white balance. Place a white paper in front of the camera when using the one
push
mode to self adapt.
INDOOR – Indoor mode will adjust white balance to indoor lighting
conditions.
OUTDOOR – Outdoor mode will adjust white balance to outdoor lighting
conditions.
MANUAL – Manual mode will adjust white balance manually.
BLUE – 0 ~ 100 ( Select blue gain within the range of 0 to 100 )
RED – 0 ~ 100 ( Select Red gain within the range of 0 to 100 )
AE CONTROL
AUTO
Auto mode will adjust the exposure level automatically.
Detailed fine tuning options are available under this menu.
-
AGC MAX: OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX
“AGC MAX” sets the maximum gain value to control the video noise caused by Auto Gain Control. -
SENS UP : OFF, x2 ~ x10
“SENS UP” mode controls the digital slow shutter to allow extra light into the camera and adjust the picture quality. -
AE BRIGHT: 0~20 – (Auto Exposure brightness level can be adjusted)
SHUT FIX
SHUT FIX mode provides more detailed shutter speed option.
All other controls are tuned for the selected shutter speed.
-
SHUTTER: AUTO, 1/30 ~ 1/10,000 ( Shutter speed can be set )
-
AGC MAX: OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX
“AGC MAX” sets the maximum gain value to control the video noise caused by Auto Gain Control. -
SENS UP: 0~20
“SENS UP” mode controls the digital slow shutter to allow extra light into the camera and adjust the picture quality. -
AE BRIGHT : 0~10
Auto Exposure brightness level can be adjusted.
AGC FIX
AGC FIX mode provides more detailed gain option.
All other controls are tuned for the selected gain value.
-
AGC: AUTO, 0dB ~ 27dB ( Gain level can be set )
-
AGC MAX: OFF, LOW, MIDDLE, HIGH, DMIN, DMID, DMAX
“AGC MAX” sets the maximum gain value to control the video noise caused by Auto Gain Control. -
AE BRIGHT: 0~10
Auto Exposure brightness level can be adjusted.
MANUAL
MANUAL mode provides more detailed fin tuning options.
-
SHUTTER: AUTO, 1/30 ~ 1/10,000 ( Shutter speed can be set )
-
AGC : 0dB ~ 27dB ( Gain level can be set )
-
SENS UP : OFF, x2 ~ x10
“SENS UP” mode controls the digital slow shutter to allow extra light into the camera and adjust the picture quality. -
LENS MODE: INDOOR, OUTDOOR, MANUAL
Lens setting will be optimized for the selected environment. ( DC Iris lens only ) -
FLK CONTROL : AUTO, ON, OFF
“FLK CONTROL” mode provides a proper image sensor frequency to match the power frequency in order to minimize video flicker.
DAY & NIGHT
Adjust color or B&W setting from this menu.
-
MODE: DAY(COLOR), NIGHT(B&W)
Set camera to either color mode or B&W mode. -
NIGHT COLOR: ON, OFF
When “NIGHT COLOR” is turned ON, camera stays on color mode even “NIGHT(B&W)” is selected from the MODE.
AUDIO
MODE: OFF, LINE, MIC
Select the proper audio mode from this menu.
AUDIO LEVEL: -12dB ~ 48dB
Audio level can be manually adjusted from this menu.
MIC ATTENUATOR: ON, OFF
Audio input attenuation can be controlled from this menu to minimize the audio
noise level.
AGC LIMIT: -0dB ~ 58dB
Audio gain level can be adjusted from this menu when MIC attenuation is
enabled.
SAMPLE BITS: 16, 20, 24, 32 ( Audio sample bit rate can be adjusted from
this menu )
IMAGE CONTROL
-
CONTRAST: 0 ~ 20 ( Contrast level can be adjusted )
-
BRIGHTNESS: 0 ~ 20 ( Brightness level can be adjusted )
-
SATURATION: 0 ~ 20 ( Saturation level can be adjusted )
-
HUE : 0 ~ 20 ( Hue level can be adjusted )
-
EDGE ENHANCE : 0 ~ 20 ( Image sharpness level can be adjusted )
-
AUTO SATURATE: OFF, LOW, MIDDLE, HIGH
Decrease saturation automatically when noisy scene is detected. -
AUTO EDGE: ON, OFF
Decrease edge enhancement (sharpness) automatically when noisy scene is detected.
IMAGE CONTROL
Camera image control can be adjusted from EFFECT menu.
-
BLACK WHITE LV: -64 ~ 64 ( Gamma level can be adjusted )
-
GAMMA CORRECT: DEFAULT, 0.4 ~ 1.0 ( Gamma level can be adjusted )
-
DNR: Camera noise level can be adjusted from this menu.
-
DNR MODE: OFF, 2D, 3D, 2D+3D
Digital noise reduction can be applied from this menu. -
DNR LEVEL: AUTO, LOW, MIDDLE, HIGH
Noise reduction level can be adjusted from this menu. -
DNR APERTURE : 0 ~ 4 ( Motion artifacts tightness can be adjusted ).
SPECIAL
Camera special functions can be adjusted from SPECIAL menu.
D ZOOM: ON, OFF
Digital Zoom and PIP function can be enabled from this menu.
- ZOOM CONTROL: RATIO, POSITION, RETURN
Adjust the digital zoom ratio and position.
Use LEFT / RIGHT button to adjust the ratio, then press select.
USE LEFT / RIGHT/ UP / DOWN button to adjust the image position, then press select. Press select to exit.
DEFOG: ON, OFF, AUTO
“DEFOG” menu improves foggy image.
-
STRENGTH : 0 ~ 16
Change defog strength. -
THRESHOLD : 0 ~ 3
Threshold value sets minimum sensitivity value for automatic defog control.
Higher value makes defog-on control reluctant. -
AUTO LEVEL: LOW, MID, HIGH
Auto level value sets maximum strength value for automatic defog control.
Higher value makes defog effect to be stronger.
BINNING: OFF, ON
Binning can be turned ON or OFF.
DEFECT PIXEL: OFF, ON, ON (FIXED), STATIC
Defective Pixel Correction feature can be operated.
It is turned ON by default and will run both dynamic and static DPC function.
DISPLAY FUNCTION:
Adjust image display features from this menu.
- FREEZE : OFF, ON
Image freeze can be turned ON or OFF.
PICTURE STYLE : OFF, STANDARD, VIVID, CLEAR, VIVID CLEAR, NEUTRAL
Different types of picture style can be applied.
PRIVACY
Privacy zone can be setup from this menu.
MODE: ON, OFF
Enable “PRIVACY ZONE” ON or OFF.
TYPE: SQUARE, POLYGON
Select privacy zone shape.
MASK NO: MASK1 ~ MASK8
Select privacy zone mask number.
DISPLAY: ON, OFF
Turn ON or OFF the selected privacy mask zone.
COLOR: WHITE, GREEN, BLUE, RED, CYAN, MAGENTA, YELLOW, GRAY-1 ~ 6,
MOSAIC, BLACK. ( Select privacy zone mask color
POLY SELECT: L- TOPP, L- BOTTOM, R- TOP, R-BOTTOM
Change the shape of the polygon by selecting the corner of the polygon.
POSITION-X & POSITION-Y
Change the size of the selected corner from “POLY SELECT” menu.
SIZE-X & SIZE-Y
Change the size of the privacy square.
DEFAULT
Set privacy zone to default value.
SETUP
Camera setup can be adjusted from this menu.
CAM TITLE: OFF, ON
Camera title can be turned ON or OFF.
COMMUNICATION: VISCA communication control can be adjusted
- CAM ID : 0 ~ 7 ( Camera ID can be setup )
- ID DISPLAY: OFF, ON ( Camera ID can be setup )
- BAUDRATE : 2400, 4800, 9600, 19200, 38400 ( Camera baudrate can be set )
SYSTEM INFO: ON, OFF, AUTO ( Camera information can be found under this menu )
OUTPUT FORMAT: ON, OFF, AUTO ( Camera resolution and frame rate can be set )
RESET
MODE: FACTORY, USER
Camera will reset to factory default or user saved value.
RESET: Reset the camera to the selected mode.
SAVE AS USER: Save the user desired setting from the menu. ( Mode must be
set to User )
SPECIFICATION
| VIDEO | AUDIO INPUT |
|---|---|
| Image Sensor | 1/7” inch Progressive CMOS |
| Sensor Size | Diagonal 9.93mm(17:9) |
3.5mm TRS Stereo
Mic-in & Line in over I/O Cable
Effective Pixels| Horizontal: 4096, Vertical: 2160| Sample Rate|
16/24/32 Bits
Pixel Size| 1.85 µm x 1.85 µm| PHYSICAL
Resolution| 4096 x 2160, 3840 x 2160, 1920 x 1080, 1280 x 720|
Camera Control| RS-485, OSD Button
Resolution/Rate| 4K (4096 X 2160) 60/59.94/50/30/29.97/25/24
3840p 60/59.94/50/30/29.97/25/24p
1080p 60/59.94/50/30/29.97/25p/24p
1080i 60/59.94/50i
720 60/59.94/50p| Operation Temp| 15°F – 120°F
Output| HDMI 2.0| Dimension| 51mm x 51mm x 102mm / 2.01” x
2.01” x 4.01”
Color Spac e| 4:2:2 (YCbCr) 10bit| Weight| 384g / 0.84lbs
LENS| Power| 12VDC (+9 – +15VDC)
Lens| C/CS Mount (with 4K 3.6mm – 11mm vari-focal lens)| |
QUESTIONS
Visit us:
www.aidaimaging.com/support
E-mail us:
[email protected]
Give us a Call:
Toll Free: 844.631.8367 | Tel: 909.333.7421
Operating Hours: Mon-Fri | 8:00am – 5:00pm PST
Disposal of Old Appliances
1. When this crossed-out wheel bin symbol is attached to a product it means
the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately
form the municipal waste stream in accordance to laws designated by the
government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please
contact your city office, waste disposal service or the shop where you
purchased the product.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful inter reference in which case the user will be required to correct the interference at his own expense.