WilTec 61106 Soldering Iron Kit with Case User Manual
- June 13, 2024
- wiltec
Table of Contents
WilTec 61106 Soldering Iron Kit with Case
Product Information
Product: Soldering Iron Kit with Case
Model Number: 61106
Manufacturer: WilTec Technik GmbH
Important Safety Information
- Read and follow the operating instructions and safety information before using the product for the first time.
- Handle the device with care as temperatures of parts of the station can reach up to 480°C during operation.
- Keep these operation instructions safe for future reference.
Technical Specifications
Intake voltage (V)| Intake frequency (Hz)| Power consumption (W)| Weight (kg)|
Size (cm)
---|---|---|---|---
230| 50| 100| 0.96| Details not provided
Disposal Regulations
All WilTec electric devices that fall under the Waste Electrical and
Electronic Equipment (WEEE) regulations are labeled with the crossed-out
wheeled waste bin logo. This indicates that the product must not be disposed
of with domestic waste. WilTec Technik GmbH is registered in the German
registry EAR under the WEEE registration number DE45283704. For information on
recycling this product, please contact your local community, municipal waste
disposal facilities, or the store where you purchased the product.
Note : The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction manual require the written permission of WilTec Wildanger Technik GmbH.
Product Usage Instructions
- Before using the soldering iron kit, read and understand the entire operation manual.
- Ensure that you have taken necessary safety precautions to minimize the risk of injury.
- Handle the device with care as temperatures of parts of the station can reach up to 480°C during operation.
- Connect the soldering iron to a power source with an intake voltage of 230V and an intake frequency of 50Hz.
- Wait for the soldering iron to heat up to the desired temperature.
- Use the soldering iron to solder components or wires as required.
- After use, allow the soldering iron to cool down before storing it in the provided case.
If you have any questions or need assistance with the product, please contact
WilTec Technik GmbH’s customer service team.
Read and follow the operating instructions and safety information before using
for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps, and technical
data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities,
please contact us.
The information contained in this document may alter at any time without previous notice. It is prohibited to copy or spread any parts of this document in any way without prior written allowance. All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual or in the diagrams and figures shown. Even though the WilTec Wildanger Technik GmbH has undergone the biggest possible efforts to ensure that the operating manual is complete, faultless, and up to date, mistakes cannot be entirely avoided. If you 9should find a mistake or wish to make a suggestion for improvement, we look forward to hearing from you.
Send an e-mail to:service@wiltec.info
or use our contact form:https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in
our online shop via:https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
Do you wish to pick the goods up? Our pick-up address is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
Germany
To shorten the waiting time and allow for a rapid on-site transaction, we ask you to call us previously or place your order via the webshop.
E-mail: service@wiltec.info
Tel:+49 2403 55592-0
Fax: +49 2403 55592-15
To return orders for exchange, repair or for other purposes, please use the
following address. Attention!
To allow for a smooth execution of your complaint or return, it is important
to contact our customer service team before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: service@wiltec.info
Tel:+49 2403 55592-0
Fax: +49 2403 55592-15
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury we urge that our clients take some basic safety precautions when using this device. Please read the operation instructions carefully and make sure you have understood its content. Keep these operation instructions safe
Important notes
|
CAUTION!
| To avoid serious injuries, be careful and observe the following precautions
when using the soldering gun!
---|---|---
- Perform a visual inspection of the device before each usage. Do not use the device if safety parts are damaged or worn out. Never override safety parts.
- Only use the device in accordance with the purpose specified in this manual.
- You are responsible for safety in the work area.
- If the cable or plug is damaged due to external influences, it may not be repaired! The cable must be replaced with a new one.
- The voltage of 230 V AC specified on the type plate must correspond to the existing mains voltage.
- Never lift, transport or secure the unit by the power cord.
- Make sure that the electrical connectors are protected from flood and moisture.
- Avoid exposing the device to a direct jet of water.
- The operator is responsible for compliance with local safety and installation regulations. (Ask an electrician if necessary)
- In the case of a defect of the device, repairs may only be carried out by a qualified electrician.
Safety instructions
Please note the following advice for your own safety, otherwise damage or
injury may result:
Temperatures of parts of the station can be up to 480 ℃ in operation,
therefore:
- Do not use the station near flammable gases, paper or other flammable substances.
- Avoid touching hot parts of the station, otherwise, you may burn yourself seriously.
- Do not touch metal parts near the soldering tips.
- Place the soldering gun on heat-resistant surfaces only.
- NEVER immerse these in water!
- ALWAYS grasp the soldering gun by the handle, not the tip.
Handle the device with care.
- Never drop it and do not hit it.
- It contains sensitive components that can be destroyed if used improperly.
- It is recommended to leave the soldering gun powered for a maximum of one minute at a time and then to pause for at least four minutes before being put back into service. This extends the life of the device.
- Disconnect the device from the mains if you are not going to need it for a long time, if there is a power failure or before you open it.
- Soldering creates potentially harmful fumes. Solder only in a well-ventilated workplace to avoid harmful concentrations.
- Do not make structural changes to the device.
Operation hints
- Check for the correct voltage before each use of the device.
- Make sure that the gun is fastened and the locking screw is tightened.
- Connect the device to the mains.
- Make sure the connection points are clean and free of grease.
- Use the soldering gun to heat the connection points, NOT the soldering tin.
- Apply the solder after heating the connection points.
- Let the soldered material cool down.
- The gun can be cleaned well with a damp sponge while the tip is still hot.
- After use always clean the soldering tip and re-tin it before switching off. This protects the soldering tip from oxidation and increases the service life of your soldering tip.
PLEASE NOTE!
- Please follow the instructions and tips to ensure proper operation of your device
- Values recommended by industry:
- 315–320 ℃ for normal solder
- 340–370 ℃ for lead-free solder
Technical specifications
| Intake voltage (V) | 230 |
|---|---|
| Intake frequency (㎐) | 50 |
| Power consumption (W) | 100 |
| Weight (㎏) | 0.96 |
| Size (㎝) | 42.5 × 27 × 32.5 |
| Details | TÜV-certified and safety-tested, in a practical case |
(TÜV = Technischer Überwachungsverein, Technical Inspection Associ- ation)
Accessories
| 1 × soldering gun 1 × soldering paste 1 × solder wire
2 × soldering tip
Disposal regulations
EU guidelines regarding the disposal of scrap electric appliances (WEEE, 2012/19/EU) were implemented in the law related to electrical and electronic equipment and appliances. All WilTec electric devices that fall under the WEEE regulations are labeled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed of with domestic waste. The company WilTec Technik GmbH has been registered in the German registry EAR under the WEEE registration number DE45283704.
Disposal of used electrical and electronic appliances (intended for use in the countries of the European Union and other European countries with a separate collection system for these appliances). The logo on the article or on its packaging points out that this article must not be treated as normal household waste but must be disposed of at a recycling collection point for electronic and electrical waste equipment. By contributing to the correct disposal of this article you protect the environment and health of your fellow men. Environment and health are threatened by inappropriate disposal. Material recycling helps reduce the consumption of raw materials. Additional information on recycling this article can be provided by your local community, municipal waste disposal facilities or the store where you purchased the article.
Address:
WilTec Wildanger Technik GmbH
Königsbenden 12 / 28
D-52249 Eschweiler
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in
part, of this instruction manual require the written permission of WilTec
Wildanger Technik GmbH.
© by WilTec Wildanger Technik GmbH
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
References
- Aoyue.de
- Teichtip.de
- WilTec - Ihr Online Shop für Haus, Garten, Werkstatt, Freizeit
- Unternehmen: WilTec Wildanger Technik GmbH
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>