Sunbeam 32610015 1700W Digital Steam Iron Instruction Manual

Sunbeam 32610015 1700W Digital Steam Iron

IMPORTANT INSTRUCTIONS

• Only use an iron for its intended use.
• To avoid the risk of electric shock, do not immerse the iron in water or other liquids.
• Always turn the iron OFF before plugging or unplugging the iron from the electrical outlet.
• Never pull on the cord to disconnect the iron from the electrical outlet; instead, grasp the plug and pull on the plug to disconnect the iron.
• Do not let the cord touch hot surfaces. Let the iron cool completely before putting the iron away. Coil the cord loosely around the iron when storing.
• Always disconnect the iron from the electrical outlet before filling the iron with water, emptying the water from the iron, and when the iron is not in use.
• Do not operate the iron with a damaged cord or in the event the iron has been dropped, damaged or is leaking. To avoid the risk of electric shock, do not disassemble the iron.
• Take it to a qualified serviceman for examination and repair. Incorrect assembly might result in a risk of electric shock when the iron is used after reassembly.
• Close supervision is required for any appliance used by or near Children. Do not leave the iron unattended while the iron is connected or on an ironing board.
• Bums can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down – there might be hot water in the reservoir.
• To avoid a circuit overload, do not operate an iron on the same circuit with another high-wattage appliance.
• lf an extension cord is absolutely necessary, a cord with an ampere rating equal to or greater than the maximum rating of the iron shall be used. A cord rated for less amperage can result in a risk of fire or electric shock due to overheating. Care shall be taken to arrange the cord so that it cannot be pulled or tripped over.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• Always unplug the electric iron before filling the water reservoir.
• Do not open the water reservoir during use.
• Always use and rest the appliance on a heat-resistant, dry, stable, level surface.
• To reduce the risk of contact with hot water emitting from steam vents, check the appliance before each use by holding and facing it away from the body and operating the steam button.
• When filling the water reservoir, do not allow water to drip onto the floor.
• To avoid personal injury and damage to the appliance, only add water to the Ille water reservoir. Never add cleaning solutions, perfumes, oils, or any other chemical additives.
• The use of attachments not recommended or sold by the appliance manufacturer may cause injuries or void your warranty.
• Use caution while operating the appliance due to the emission of steam.
• For models with retractable cords: Always hold the plug while retracting the cord.
• Only use the stand provided.
• Place the iron on its stand after use. Make sure the stand is placed on a heat-resistant, dry, stable, level surface.

FEATURES

• Sole Plate
• Skirt
• Handle
• Spray Nozzle
• Filler Cover
• Top Cover
• Temperature Selector Button
• LCD Display Cover
• Spray Button
• Steam Selector Knob
• Sos Trigger
• Tank
• Cord Reel Cover
• Retract able Button

DRY IRONING

• Ensure the Steam Lever is turned to the & (Dry) setting.
• Plug the cord into a 120-volt AC outlet.
• Press the Fabric Select Button to select the desired fabric setting. Allow the iron to heat until the light under the selected fabric setting turns solid blue.
• While iron is heating, make sure it is sitting on a stable, protected surface. Light will blink until the temperature is reached.

NOTE: While Steam Lever is turned to the * (Dry) setting, you may still use the Shot of Steam® or Spray Mist features, as long as the Fabric Select Dial is set to wool, cotton, or linen.

IMPORTANT: The water reservoir must be at least ¼ full of water.

FILLING WATER RESERVOIR (use tab water)

• Turn the Steam Lever to 9% (Dry) and the Fabric Select Dial to Off. Unplug.
• Lift the Water Fill Hole Cover. Use the easy-pour measuring cup to fill the water reservoir with tap water through the water fill hole. Do not fill the water reservoir beyond the maximum fill line.
• Close the Water Fill Hole Cover completely after filling.

WARNING: To prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water, and steam can cause injuries.

STEAM IRONING

• Follow the instructions for “Filling the Water Reservoir”.
• Fill the Water Reservoir and plug the cord into a 120-volt AC outlet.
• Turn the Steam Lever to the desired steam setting. IMPORTANT: Only use the Steam setting and/or Shot of Steam® feature with Wool, Cotton, or Linen fabric settings. (below the collar line), the other shoulder and the remainder of the front.
• Iron sleeves and cuffs, working down from the underarm seams. To remove creases, shift the double layer of sleeve fabric and iron out.
• Iron body of the garment, from half of the front around the back, then the second half of the front. If your shirt does not open, slip over the end of the ironing board and iron front and back in turn.

SPECIAL FEATURES

SPRAY MIST FEATURE is a powerful water spray mist that dampens the fabric to aid in removing wrinkles from heavy fabrics and for setting creases.

TO USE: Press the Spray Mist Trigger firmly.

SHOT OF STEAM® FEATURE provides an extra burst of steam for deep penetration of stubborn wrinkles. You can use this feature while drying or Steam ironing as long as the Fabric Select Dial is set to wool, cotton, or linen. IMPORTANT: The water reservoir must be at least ¼ full of water.

TO USE : Place the iron on top of the wrinkle and press the Shot of Steams button each time you would like an extra burst of steam. The Shot of Steam® feature may be used continuously in approximately 3-second intervals

VERTICAL SHOT OF STEAM® FEATURE allows iron to function vertically as a garment steamer.

TIP: When using vertical steam, hang clothing on a hanger for best results, Hanging curtains and drapes may also be steamed.

TO USE:

• Ensure that the iron is heated up and the Ready indicator light has turned solid blue.
• Hold the iron vertically near, but not touching the fabric you want to steam, Pull the fabric tight,
• Press the Shot of Steam® button in 3-second intervals as you move the iron over wrinkles.

3-WAY MOTION SMART AUTO-OFF FEATURE
Turns iron off if left in one position too long to avoid accidents.

IF YOU LEAVE IRON ON:

• If auto-off activates the unit will beep and the red light will blink until reset.
• + Horizontally without moving it, or accidentally tipping the iron over, it will automatically stop heating after 30 seconds.
• Vertically (on its heel rest) without moving it, the iron will automatically turn off after 8 minutes.

TO RESET : Move iron back and forth and reheat until the ‘Ready” indicator light turns solid blue.

CARING FOR YOUR IRON AFTER USE

• TURNING OFF IRON: Turn the Steam Lever to 9 (Dry) and Fabric Select Dial to Off. Unplug.
• WARNING : NEVER yank the power cord when unplugging the iron. This can damage the cord.
• IMPORTANT : Empty the water reservoir completely after each use.

STORING YOUR IRON

• Tum off the iron, unplug it and allow it to cool.
• IMPORTANT: Empty water reservoir after each use for a longer iron life.
• Loosely loop the power cord around the heel rest and store the iron on its heel rest.

IMPORTANT : Wrapping the cord around the iron too tightly can damage the cord.

MAINTAINING YOUR IRON

USING SELF-CLEAN FEATURE: Use the Self-Clean feature once a month to maintain optimal iron performance.

• Turn off and unplug the iron.
• Move the Steam Lever back and forth to remove debris and minerals from the Steam Valve. This keeps water flowing into the steam chamber.
• Fill the water reservoir with tap water to the MAX line.
• Plug in the iron, press the Fabric Select Button to select the Linen setting, and heat until the indicator light turns solid blue.
• Turn off and unplug the iron. Holding the iron over a sink in a horizontal position, press the Self-Clean Button and hold. Water will begin dripping from the steam vents. Slowly rock iron side to side and front to back for 30 seconds. Dip the nose of the iron slightly below the rear to circulate water. Release the Self-Clean Button after one minute.
• Open the fill cap and empty the remaining water. Carefully dry the soleplate with a towel.
• Plug in iron set the Fabric setting to Linen and Heat for 2 minutes to dry out completely. Set the Fabric Select Dial to Off, unplug the iron, and allow it to cool.
• This appliance has no user-serviceable parts. Any servicing beyond that described in the Cleaning Section should be performed by an Authorized Service Representative only. See warranty available online.

CLEANING SOLEPLATE : Clean the soleplate after every 30 uses, or more frequently if starch is used or build-up starts to accumulate. Before cleaning, ensure the iron is unplugged and cool.

WARNING: To avoid the risk of electric shock, do not immerse the iron in water or other liquids.

NOTE : Do not use abrasive cleansers or scouring pads to clean the soleplate. This will damage the finish.

ANTI-CALCIUM SYSTEM

Anti-calcium is a permanent system located inside the water reservoir to eliminate impurities.

TO PROLONG EFFICIENCY, FOLLOW THESE STEPS ONCE A MONTH OR After Every 30 Uses:

• Turn off the iron.
• Add 1 teaspoon of salt to ¾ cup water and fill the water reservoir with this solution.
• Leave the solution in the water reservoir for 15 minutes, shake occasionally, and then empty through the fill hole.
• Fill the water reservoir again with a saltwater solution, shake it, and empty it after 15 minutes.
• Fill the water reservoir with fresh water to rinse and empty.

IRONING TIPS

• Before ironing, check the garment label and follow the manufacturer’s instructions. If no instructions, start with a low-heat setting and test by ironing a small area, and gradually increasing the heat.
• Sort garments by fabric type. Iron articles require a low-temperature setting and gradually work up the temperature range.
• When changing from a high-temperature setting to a lower one, allow 5 minutes for change.
• When steam ironing, use long, slow passes over the fabric to allow the steam to penetrate the fabric and the heat of the soleplate to dry the moisture.
• Iron linen garments inside out to prevent shine. An ironing cloth or cotton fabric can be used to reduce shine.
• If the garment is lined, use a low heat setting.
• Ensure zippers are closed and the flap is flat. Iron over the flap, holding the garment taut.
• pray starch makes the job easier.

IRONING SHIRTS

• Begin with the collar and work toward the middle from the outer edges. Iron lengthwise, not in circles.
• Lay your shoulder over the narrow edge of the board and iron one side of the front. Then iron the shoulder, across the back

IRONING PANTS

• Begin with the waistband and inseam area, then pockets and cuffs.
• Pull the waistband on the pointy end of the board, as if you’re “dressing” the ironing board. Iron the upper front part of the pants, including the waistband.
• Place pants parallel to the ironing board lengthwise so both legs are facing the same direction. Iron each leg by moving the iron back and forth along the pant leg.
• Take the cuff of the leg and bring it over towards the waistband to iron the inner part of the leg. Repeat these 2 steps for the second leg.
• Press the Fabric Select Button to select the desired fabric setting. Allow the iron to heat until the light under the selected fabric setting turns solid blue. While iron is heating, make sure it is sitting on a stable, protected surface.

IMPORTANT : When not ironing, always set the Steam Lever to * (Dry) and the Fabric Select Dial to OFF,

TROUBLESHOOTING

The red light blinks and beeps 6 times to indicate that the ironauto­ function has been activated.

• To stop blinking and reset, move the iron back and forth and allow it to re- heat until the indicator light turns solid blue.

Iron is not heating| • Ensure the iron is on and the light below the fabric setting is illuminated.

• Verifyunit is plugged in.

• Adjust fabric selection to the correct setting for your garments.

Iron will not steam| • Ensure the  wate r ta n k level is a t least ¼ full .

• Ensure the steam lever is switched on.

• Press the Shot of Steam®button several times to prime.

Iron is leaking| • Only fill with water to the MAX level.

• Allow to heat for at least 2 minutes before use, and wait until the indicator light “Ready” has turned solid blue to indicate that it is ready.

• Shot of Steam®has been pressed too frequently. Only use Shot of Steam®in 3 second intervals or less.

• Steam Setting and/or Shot of Steam®used with incorrect fabricsetting.

Only use w i th Wool , Cotton, or Linen fabric sett i ngs .

• Empty the water tank after each use and turn the steam lever off.

Iron leaves spots/flakes on clothing| • Empty the  wat e r tank complete l y afte r each use .

• Clean the soleplate when cool with a wet, damp cloth.

• Useself-cleaning feature once a month.

• Refer to the Anti-CalciumSystem section.

• Ensure the water cup used to fill the iron is clean.

Wrinkles are not sufficiently removed| • Check that the iron is set to the correct fabric setting.

• Use Shot of Steam: or Spray Mist features to help remove stubborn wrinkles.

Fabrics are getting an unwanted “shine·| • Iron cloth or a 100% white cotton fabric and place it between the garment being ironed and the iron to prevent “shine”.

WARRANTY

YEAR LIMITED WARRAN1Y AND LIFETIME LIMITED SOLBPLATB WARRANTY

This device has a limited warranty of 3 years from the original date of purchase against workmanship and defects in material. If under normal use, your product fails to operate, please contact our customer service department at info@sunbeamhome.com. A refund or replacement will be provided to you with proof of purchase. Star Elite Inc. may deny claims of damage caused by misuse or modifications of this product.

FAQs

Is the Sunbeam 32610015 Digital Steam Iron easy to use?

Yes, the Sunbeam 32610015 is designed for ease of use with intuitive digital controls.

What is the power rating of this steam iron?

The Sunbeam 32610015 Digital Steam Iron has a power rating of 1700 watts, providing quick and efficient ironing.

Can I adjust the steam settings for different fabrics?

Yes, you can adjust the steam settings to suit different fabrics, from delicate to heavy fabrics, for optimal results.

Does it have an anti-drip feature to prevent water leakage?

Yes, the iron is equipped with an anti-drip feature to prevent water leakage, keeping your clothes dry during ironing.

What is the water tank capacity of this steam iron?

The Sunbeam 32610015 has a generous water tank capacity of 12 ounces (approximately 355 milliliters).

Is there a vertical steam feature for steaming hanging garments?

Yes, you can use the vertical steam feature to easily steam hanging garments, curtains, and drapes.

Can I use tap water with this iron?

While you can use tap water, it's recommended to use distilled or demineralized water to prevent mineral buildup and maintain the iron's performance.

Does it have an auto-shutoff safety feature?

Yes, the Sunbeam 32610015 Digital Steam Iron features an auto-shutoff function for safety. It will automatically turn off after a period of inactivity.

What type of soleplate does it have?

This steam iron has a durable stainless steel soleplate, which glides smoothly over fabrics.

How do I clean the steam vents and the soleplate?

You can clean the steam vents and soleplate by following the cleaning instructions provided in the user manual.

Is there a warranty for this product?

Yes, the Sunbeam 32610015 Digital Steam Iron typically comes with a manufacturer's warranty. Be sure to check the warranty details provided with your purchase.

Can I use this iron on delicate fabrics like silk?

Yes, you can safely use this iron on delicate fabrics like silk by selecting the appropriate steam setting and using the lowest temperature setting.

What should I do if the iron doesn't produce steam?

If the iron doesn't produce steam, ensure that the water tank is filled, and the steam settings are adjusted properly. If the issue persists, refer to the troubleshooting section in the user manual.

Download This PDF Link:Sunbeam 32610015 1700W Digital Steam Iron

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>