ROLL HILL Apollo 8 Celling Light Instruction Manual

: June 13, 2024
: Roll Hill

Table of Contents

ROLL HILL Apollo 8 Celling Light
Product Information
Product Usage Instructions
APOLLO PENDANT-STEM | INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ROLL HILL Apollo 8 Celling Light

ROLL -HILL -Apollo -8 -Celling -Light -PRODUCT IMAGE

Product Information

Product Name: Apollo Pendant-Stem
Manufacturer: Roll & Hill
Contact Number: +1 718 387 6132
Website: www.rollandhill.com

Contents:

1 Apolo glass
1 Canopy with Crossbar assembly
1 T-driver
7 Wago Connectors
2 8-32 Screws (Metal)
2 Long 8-32 Screws (Metal)
2 Wood Screws
2 Toggle Anchors

$ROLL -HILL -Apollo -8 -Celling -Light -FIG $2$$

Safety Information:

Updated: 10JAN2023
Safety precautions and instructions are not provided in the manual.

Please contact a licensed electrician for installation

Product Usage Instructions

Stem Length Adjustment:
- Note: Please contact a licensed electrician.
- Cut the cover tube to the desired length.
- Cut the inner threaded tube so that it remains 1/2 longer than the cover tube.
- Recommended to clean the tube after cutting to remove any metal chippings.
- Refer to the manual illustrations for guidance.
Installation:
- Note: Please contact a licensed electrician for installation. Ensure power is off during installation.
- Unscrew the hang-straight nut (A) from the canopy (B) with crossbar assembly (C).
- Raise the crossbar assembly (C) to the junction box (D), and secure it with #8-32 screws (E). Make sure to pull out the wires from the junction box through the hole in the crossbar.
- Slide the hang-straight nut (A) and canopy (B) down the stem (F).
- Feed the black and red wires from the fixture through the hang-straight (G) and screw in the threaded stem into hang-straight.
- Fit the driver (H) into the space in the crossbar assembly (C). – Make the electrical connections between the lead AC wires and the driver using the provided Wago connectors (I).
- Connect the secondary wires to the fixture using the provided Wago connectors (J). Optionally, connect the 0-10V dimming wires (K) as needed.
- Connect the ground wire (L) with the provided Wago connector.
- Tuck all wires into the crossbar assembly.
- Refer to the manual illustrations for guidance.

Note: The above instructions are based on the information provided in the user manual. For detailed installation and usage instructions, please refer to the original user manual or contact Roll & Hill customer support.

APOLLO PENDANT-STEM | INSTALLATION

Stem and cover tube length adjustment
Note: Please contact a licensed electrician.

Example fixture only:
To measure length of stem, first determine overall length (OAL), subtract 3” for the canopy with hang-straight height and subtract the fixture height from the OAL. Fixture height is measured from bottom of the fixture to stem connection point. The resulting measurement is the final stem length.
Ex. The fixture below has an OAL of 40” and a fixture height of 6.5”. 40” OAL – 2” canopy – 6.5” fixture height = 31.5” stem

$ROLL -HILL -Apollo -8 -Celling -Light -FIG $3$$

Stem and cover tube length adjustment
Note: Please contact a licensed electrician.

Example fixture only:

To customize the length of the provided stem, cut cover tube to desired length. Then cut the inner threaded tube so that it remains 1/2” longer than the cover tube. $ROLL -HILL -Apollo -8 -Celling -Light -FIG $4$$
Mark the length of the tube required, using a marker or tape. Then hold down the tube with a hand or a clamp, use a hacksaw or electrical tool to cut the tube. Recommended to clean tube after cutting to remove any metal chippings.
Now that the cover tube is cut to 31.5”, measure the all thread tube to be 31.5 and 1/2” long. And place a mark, with a marker or tape. $ROLL -HILL -Apollo -8 -Celling -Light -FIG $6$$
Hold down the all thread with a hand or a clamp, use a hacksaw or electrical tool to cut the all thread tube. Recommended to clean all thread tube after cutting to remove any metal chippings.

Note: Please contact a licensed electrician for installation. Ensure power is off during installation.

To customize the length of the provided 36-inch stem, cut cover tube to desired length. Then cut the inner threaded tube so that it remains 3/4” longer than the cover tube. $ROLL -HILL -Apollo -8 -Celling -Light -FIG $8$$
Unscrew the hang-straight nut (A) from the canopy (B) with crossbar assembly (C).
Raise the crossbar assembly (C) to junction box (D), and secure with #8-32 screws (E). Be sure to pull out the wires from the junction box, through the hole in the cross bar. $ROLL -HILL -Apollo -8 -Celling -Light -FIG $10$$
Slide the hang-straight nut (A) and canopy (B) down the stem (F).
Then feed the black and red wires from the fixture, through the hang-straight (G), and screw in the threaded stem into hang-straight.
Fit the driver (H) into the space in the crossbar assembly (C).
Make the electrical connections between the lead AC wires and the driver using the provided wago connectors (I).
Connect the secondary wires to the fixture using the provided wago connectors (J)
(Optional: Connect the 0-10V dimming wires (K) as needed)
Connect the ground wire (L) with the provided wago connector.
Tuck all wires into the crossbar assembly. $ROLL -HILL -Apollo -8 -Celling -Light -FIG $12$$
Once all the wires are connected and tucked in, raise the canopy (B) over the crossbar assembly, and secure it with the hang-straight nut (A). $ROLL -HILL -Apollo -8 -Celling -Light -FIG $13$$
Then carefully thread the glass diffuser (M) onto the stem with LED.