CLAS OP 0046BL Inflating Gun User Manual
- June 13, 2024
- CLAS
Table of Contents
CLAS OP 0046BL Inflating Gun
Product Information
| Designation | Description |
|---|---|
| Tuyau de raccordement pneu | Tire connector hose |
| Valve de purge d’air | Air release valve |
| Gachette | Trigger |
Maintenance:
- If you need components or parts, please contact the reseller. In case of problems, please contact your authorized technician.
- For further assistance, please contact us at sav@clas.com or call +33(0)4 79 72 69 18. You can also visit our website www.clas.com.
WARNING
Before returning this product for any reason (installation problem, instructions for use, breakdown, manufacturing problem…), please contact us.
Contact :
- You can reach us by mail at sav@clas.com or by phone at +33(0)4 79 72 69 18 or go directly to our website clas.com.
- If you have changed your mind regarding your purchase, please return this product before you attempt to install it.
INTRODUCTION
Thank you for selecting our tire infl ating gun (OP 0046BL), please read this manual before carrying out any operation. This manual is an integral and essential part of the product, please keep it away from damp, heat, dust, oils, do not remove, tear or amend any parts of the manual for any reason. It must be made available to the operator and to maintenance personnel, also to ensure staff training. If case of loose or damage, ask the manufacturer for a copy, quoting the manual code. The manual must always remain with the machine, in the event of the machine being sold, it must be given to the new user. The manufacturer reserves the right to change product features at any time.
DESCRIPTION
| N° | Designation |
|---|---|
| 1 | Air gun |
| 2 | Tire connector Hose |
| 3 | Pressure Gauge |
| 4 | Air Release valve |
| 5 | trigger |
OPERATION
Note: To operate this tool, an air compressor or clean pressurized air is
required.
WARNING:
- Ensure the air supply pressure does not exceed the maximum operating pressure stated in ‘Specification’.
- Be aware that air tools may hold residual pressure after use. Always bleed air pressure from the tool after shutting off the air supply.
Inflating tires
IMPORTANT: Always refer to the tire manufacturer’s recommended inflation
pressures, and do not overinflate.
-
Fit the air chuck to the tire valve
-
With the air chuck attached securely, press the Inflating gun (5) to inflate the tire.
Note: Inflate the tire in frequent shorter bursts of air, which will allow more control of the tire inflation, minimising the risk of over- inflating the tire. Releasing the Inflating will display the tire’s current air pressure on the Pressure Gauge (3). -
If the tire is inflated too much, release the pressure and deflate the tire by pressing the Air Release Valve (4)
-
Once the desired tire pressure is achieved, disconnect the air chuck from the tire
Notes:
- This product is not suitable for use a spray gun or any other application for which it is not designed
- After inflating tires, remember to replace the tire’s valve covers, which protect the valve from dust and dirt
SPECIFICATIONS
- Pressure range: 0-12bar/0-174psi
- Air inlet: 1/4″ NPT
- Hose length(approximately): 400mm
- Dial display: 0-12bar/0-174psi
MAINTENANCE
WARNING: Always disconnect from the air supply and depressurise before
cleaning or carrying out any maintenance.
Note: There is very little that can go wrong with your air tool and it
should be noted that when an air tool fails to work
it is generally because the internal workings have corroded due to dirty, wet
air and failure to follow the operating
instructions.
Cleaning
- Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the tool’s service life. Clean the body of your tool with a soft brush, or dry cloth.
Lubrication
- Even though the air passages of the air tool must remain free of oil and other contaminants, some components require frequent lubrication.
- Slightly lubricate all sealing surfaces, packings, bearings and dynamic O-rings with a specialised air tool lube, and apply a small amount of petroleum jelly to springs and pins, such as the Inflating gun (5).
contact
- @clas-equipments.com.
- www.clas-equirements.com.
- CLAS Equipements
- ZA de la CROUZA
- 73800 CHIGNIN
- FRANCE
- Tél. +33 (0)4 79 72 62 22
- Fax. +33 (0)4 79 72 52 86
If you need components or parts, please contact the reseller. In case of problems, please contact your authorized technician.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>