CLAS OM 3060 Pair of 6T Jack Stands with Security Pins User Manual
- June 13, 2024
- CLAS
Table of Contents
OM 3060
PAIRE CHANDELLES CREMAILLERES 6T
AVEC GOUPILLES SECURITE
PAIR OF 6T JACK STANDS WITH SECURITY PINS
OM 3060 Pair of 6T Jack Stands with Security Pins
clas.com
OM 3060
WARNING
Before returning this product for any reason (installation problem,
instructions for use, breakdown, manufacturing problem…), please contact us.
Contact : You can reach us by mail [email protected] or by
phone +33(0)4 79 72 69 18 or go directly to our website
clas.com
If you have changed your mind regarding your purchase, please return this
product before you attempt to install it.
PAIR OF 6T JACK STANDS WITH SECURITY PINS
CHARCTERISTICS
- Min. H.: 388mm
- Max. H.: 580mm
- Weight: 13,6kg
- Standards: AfPS GS 2014:01 PAK, EK5/AK6 09-12:2009
SAFETY INFORMATION
Please read these safety warnings before operation.
- Failure to heed these warnings may result in a loss of load, damage to the axle stands, and/or personal injury or property damage.
- Do not overload jack stands beyond their rated capacity.
- Overloading can cause damage or failure of the axle stands.
- Position the load on the centre saddle only, on each axle stand that you use.
- Always use axle stands in pairs, and place on a hard, level surface capable of sustaining the load.
- Use of stands on anything other than a hard level surfacecan result in axle stand instability and possible loss of load.
OPERATING INSTRUCTIONS
- Refer to your vehicle owner’s manual for proper jacking instructions. Lift only on areas of the vehicle as specified by the vehicle manufacturer.
- Position stands under the vehicle at points specified by the vehicle manufacturer as proper load support points.
- To adjust the stands hold the control lever up while lifting the saddle shaft to the desired height. Push the control lever down to lock pawl into the teeth loaded in the centre column. Ensure the pawl is fully engaged into the teeth.
- Carefully lower the load onto the stands.
- Visual inspection should be made before each use of the stands – checking for cracks, cracked welds and missing and/or damaged parts. An axle stand that appears to be damaged in any way must be removed from service immediately.
- Because of the potential hazards associated with the misuse of this equipment, no modifications should be made to the product.
DECLARATION OF CONFIRMITY
We,CLAS EQUIPEMENTS
Z. A. de la Crouza
73800 Chignin – France
DECLARE THAT,
Under our responsibility, the following products:
Model : PAIRE CHANDELLES CREMAILLERES 6T AVEC GOUPILLES SECURITE / PAIR OF 6T
JACK
STANDS WITH SECURITY PINS
Type : OM 3060
Is manufactured in conformity with the European Directive:
- AfPS GS 2014:01 PAK
- EK5/AK6 09-12:2009
Philippe Barrault, 17.06.2020
……………………..
CLAS Equipements
83 Chemin de de la CROUZA
73800 CHIGNIN
FRANCE
Tél. +33 (0)4 79 72 62 22
Fax. +33 (0)4 79 72 52 86
OM 3060
PAIRE CHANDELLES CREMAILLERES 6T
AVEC GOUPILLES SECURITE
PAIR OF 6T JACK STANDS WITH SECURITY PINS
If you need components or parts, please contact the reseller.
In case of problems, please contact your authorized technician.
CLAS EQUIPEMENTS – SAS au capital de 130 000€, R.C.S Chambéry : 409 786
944, N° TVA Intracommunautaire FR 13 409 786 944
Siège social, Z.A de la Crouza – 73800 CHIGNIN – FRANCE
+33 (0)4 79 72 62 22 –
+33 (0)4 79 72 52 86
[email protected]
– www.clas.com