FLYSKY FS-R11P-BS Receiver with Gyro Stabilization Instruction Manual

: June 13, 2024
: Flysky

Table of Contents

Introduction
Overview
Specification
Binding
Failsafe
Certifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FS-R11P-BS Receiver with Gyro Stabilization
Instruction Manual

Introduction

FS-R11P-BS based on 2A-BS protocol is a receiver which provides 11-channel and bidirectional transmission, featuring external single antenna and PWM signal output. It can adapted to a variety of model cars or boats.

Overview

FLYSKY FS-R11P-BS Receiver with Gyro Stabilization -
overview

[1] CH1 Interface
[2] CH2 Interface
[3] CH3 Interface
[4] CH4 Interface
[5] CH5 Interface
[6] CH6 Interface
[7] CH7 Interface
[8] CH10 Interface| [9] CH11 Interface
[10] LED
[11] Antenna
[12] CH9 Interface
[13] CH8 Interface
[14] S(CH Interface Signal Pin)
[15] “+”(CH Interface Anode)
[16] “-“(CH Interface Cathode)
---|---

Specification

Product Name: FS-R11P-BS
Adaptive Transmittes: FS-MG11-BS
Adaptive Models: Cars or boats
PWM Channels: 11
RF: 2.4GHz ISM
Maximum Power: <20dBm (e.i.r.p.) （EU）
Antenna: Single External Antenna
Distance: >150m (Ground Distance without Interference)
2.4G Protocol: 2A-BS
Resolution: 4096
Data Output: PWM
Input Power: 3.5 ~ 8.4V/DC
Working Current:20mA/5V
Online Update: None
Temperature Range: -10℃ ~ +60℃
Humidity Range: 20% ~ 95%
Water Proof: PPX4
Dimensions: 35.0mm23.3mm13.3mm
Weight: 8g
Certifications: CE, FCC ID: 2A2UNR11P01

Binding

The receiver will automatically enter bind mode matching state upon power-on. The operation steps are as follows:

Put the transmitter in bind mode(The transmitter may enter bind mode in different ways, please follow the transmitter’s instruction manual).
The receiver is powered on and wait 1 second. If there is no connection, the receiver will automatically enter bind mode.
The receiver LED will be solid on after the binding process is successful.
Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems arise.

Notes:

During the bind mode, put the transmitter in bind mode first, then put the receiver in bind mode, If the binding process is not completed within 10 seconds, the receiver LED goes into a slow flashing state.
The FS-R11P-BS receiver complies with the 2A-BS protocol and is only compatible with transmitters conforming to this protocol.

Failsafe

The failsafe function is used to protect the model and personnel when the receiver loses its signal and is out of control .
By default, the receiver will keep the final output after losing control. If it has been set at the transmitter end, it will output according to the set value.
Note: Whether the receiver is set at the transmitting end or not, the CH2 channel throttle has no output signal when the failsafe function is triggered.

Attentions:

Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
Make sure the receiver’s battery is disconnected before turning off the transmitter, failure to do so can result out of control.
Unreasonable setting of the Failsafe may cause accidents.
Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise.
Keep the receiver’s antenna at least 1cm away from conductive materials such as carbon or metal.
Do not power on the receiver during the setup process to prevent loss of control.

Certifications

FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

EU DoC Declaration
Hereby, [Flysch Technology Co., Ltd.] declares that the Radio Equipment [FS- R11P-BS] is in compliance with RED 2014/53/EU.
The full text of the EU DoC is available at the following internet address: www.flyskytech.com/info_detail/10.html
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 centimeters between the radiator and your body.
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

FCC ID: 2A2UNR11P01

|
---|---
http://weixin.qq.com/r/8UiKkvbEAKt-rbLx9x3j| https://space.bilibili.com/439932670
|
http://www.flysky-cn.com/| https://www.facebook.com/flyskyrc/

Manufacturer: ShenZhen FLYSKY Technology Co., Ltd.
Address: 16F, Huffing Building, No. 6006 Shenna Road, Fustian District, Shenzhen, Guangdong, China
Figures and illustrations in this manual are provided for reference only and may differ from actual product appearance. Product design and specifications may be changed without notice.

http://www.flysky-cn.com
Copyright ©2023 Flysky Technology Co., Ltd.